Obuntu M92 preview images - Page 2

crazydog · 07-10-2013, 05:09 AM

as pkbo pointed out correctly boox was not seeing the second ext3 partition.
But when the first partition is fat32 it auto mounts it and recognizes the ext3 partition. I don't know more - I'm just a noob. So I'm not saying it must be FAT32 but it works for me.
- maybe it works because this time I did it with fdisk instead of grub..

fdisk is not available on boox. Preparing SD card is much easier and faster on pc.

pkbo · 07-10-2013, 05:57 AM

@crazydog great, you did it! Can you post here output of fdisk -l [whatever device corresponds to your sd card]?

crazydog · 07-10-2013, 06:17 AM

seaniko7 opened a new world to ebook reader. fantastic

@pkbo: output of fdisk (SD Card)

Disk /dev/sdc: 7948 MB, 7948206080 bytes
245 heads, 62 sectors/track, 1021 cylinders, total 15523840 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x0004f64f

Device Boot Start End Blocks Id System
/dev/sdc1 2048 4194303 2096128 b W95 FAT32
/dev/sdc2 4194304 15523839 5664768 83 Linux

por · 07-10-2013, 06:51 AM

Quote:

Originally Posted by crazydog

waaa I got it

SEANIKO7 is the KING

I formatted the first partition on sd card as fat32 - the second as ext3. I did it with fdisk instead of grub.

Obuntu is working really fast.

Great

Did you do the partitioning and unpacking under windows or linux?

If you have some spare time, could you post here the steps you did in some more detail?

crazydog · 07-10-2013, 07:20 AM

@por
fdisk /dev/sdx --where x is the sd card
m prints the help commant (really helpful)
n creates new partition
then you have to set the size, I set it with +xxxx where x is the number of sectors
then you have to format it... and repeat that to create a second partition

tar -pxjvf is the command i used to extract the rootfs (where p is needed to preserve permissions)

I hope I could help you a bit.

gamba66 · 07-10-2013, 11:57 AM

Can anyone film this and put this on youtube?

Not only to gain attention but also because I would like to see this

And is there any practical use or will there be? Must be cool to run linux but in the end it runs on an e-ink display

rogerpiano · 07-10-2013, 01:41 PM

hello to all. I am following with great attention the developments of the discussion. I'm a non-expert user of linux and I know that seaniko7 said that for now ported to ubuntu is recommended for expert users. I though I would try, as I think many, and I tried to merge the instructions of seaniko7 with the advice of CrazyDdog to get a more detailed procedure possible. I hope seaniko7 or CrazyDog can control this procedure and give the ok. for me to point 4 is still unclear. thank you very much, I look forward ...

1 - Download uImage-initramfs from:
https://github.com/intromatyk/public_kernel/tree/iMX508

1.1??? - Copy the file uimage-initramfs in internal memory of boox (is my personal interpretation)

2 - Flash uImage-initramfs using dd command

with betty boox terminal emulator : dd if=/media/flash/update/uImage-initramfs of=/dev/mmcblk0 bs=512 seek=12288

3 - Download current rootfs from:
https://www.dropbox.com/s/n50udy9rki...060713.tar.bz2

4 - Format SD and create two ext3 partitions

I formatted the first partition on sd card as fat32 - the second as ext3. I did it with fdisk instead of grub.

fdisk /dev/sdx --where x is the sd card
m prints the help commant (really helpful)
n creates new partition
then you have to set the size, I set it with +xxxx where x is the number of sectors
then you have to format it... and repeat that to create a second partition

is this operation in boox with betty boox or in windows??

5 - Unpack rootfs on second partition preserving permissions and symbolic links

tar -pxjvf (with betty boox, is my personal interpretation)

6 - Boot OS using update procedure (i.e. reboot holding Back button)

Feher · 07-10-2013, 02:26 PM

Awesome Work seaniko. I am a noob, so i cannot try this.

I want to know one thing - How is the refresh rate in Obuntu. Is something like No-Refresh possible?

por · 07-10-2013, 04:57 PM

Quote:

Originally Posted by rogerpiano

2 - Flash uImage-initramfs using dd command

with betty boox terminal emulator : dd if=/media/flash/update/uImage-initramfs of=/dev/mmcblk0 bs=512 seek=12288

I simply took the flash.oar file from the utility provided for removing the password protection and changed it with a text editor to:
dd if=/media/flash/update/uImage-initramfs of=/dev/mmcblk0 bs=512 seek=12288
, is that ok?

Quote:

Originally Posted by rogerpiano

is this operation in boox with betty boox or in windows??

I think this operation has to be done on a linux machine...

underscore · 07-11-2013, 01:18 AM

i made a quick tour on my m92 using

https://www.mobileread.com/forums/sho...89&postcount=5

i can see that the main disk is called /dev/mmcblk0 and it's splitted on tre linux partition (id=83) mounted a /, /root and /media/flash

The other disk being the external sd card.
So basically overwriting with dd the provided uImage-initramfs to /dev/mmcblk0 must be done as root and is a potential brick of the device.

I would like to mount -o loop the provided dd image on a linux machine on a mount point but i was not able.
Maybe my command is not correct.

mount -o loop,offset=32256 uImage-initramfs /tmp/
i have back
mount: unknown filesystem type '(null)'

i will feel more reassured if i can see the difference between the image and my current artatech system.
Maybe with a different tar archive for each of the 3 file systems to overwrite.

seaniko7 · 07-11-2013, 02:58 AM

@underscore, you can not mount uImage-initramfs, as it's compressed kernel with initramfs.

Also, you cannot brick device without overwriting two kernels (basic one, and second used for updates). Even then, you can reflash your Boox using MFG tool.

@Feher, as I mentioned in other thread, Obuntu is designed to work in two modes :

Quote:

I'm writing directly to epdc framebuffer, also I used imx xorg display driver instead of fbdev.

Scren updates are handled by screen_updater daemon, which constatnly refreshes screen at 1bpp (~300ms) or 4bpp (~900ms). Moreover, it can be configured to check which parts of screen changed and perform partial update.
I need to write gui control panel which will use domain sockets or dbus to change screen_updater preferences...

Default username and password can be found in first post.

Personally I use parted for partitioning SD card, and extract rootfs contents on Linux machine, NOT on Boox directly.

crazydog · 07-11-2013, 08:54 AM

M92 Obuntu using Synaptic to install Software
https://www.dropbox.com/s/6z0egtjzcr...u_Synaptic.mp4

M92 Obuntu Midori Browser
https://www.dropbox.com/s/h86kwple40...ntu_Midori.mp4

M92 playing video
https://www.dropbox.com/s/l3wdlcc7kh...Bunny_480p.mp4

underscore · 07-12-2013, 04:07 AM

Thx for the videos!
Impressive the movie on e-ink.
Obuntu looks pretty fast.

Is the joystick usable as well?
The plan is to browse documents in a folder and double click them to read, exactly how we are used to use the reader :-)

seaniko7 · 07-12-2013, 04:21 AM

@underscore, all keys are usable, but I haven't mapped them yet. For now only "Enter" works out-of-the-box.

Now I'm writing initramfs based bootloader, then I'll focus on further development of system image.

lunohod · 07-12-2013, 09:26 AM

@seaniko7

Will you publish the screen_updater source code?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
M92 Screen Update problem with images	Killy	Onyx Boox	1	11-19-2012 12:51 PM
Android [WIP] Overclocking the PE	plasticarmyman	enTourage eDGe	16	06-11-2012 07:08 PM
small preview page images	goodnerd	Kindle Formats	5	09-22-2011 11:39 AM
Seriously thoughtful I always knew Windows was a WIP	GeoffC	Lounge	4	02-06-2010 02:20 AM
Opinions needed on a WIP ebook	Nate the great	Workshop	5	07-15-2009 11:38 AM

07-10-2013, 05:09 AM	#16
crazydog error Posts: 54 Karma: 5810 Join Date: Jan 2012 Device: Kindle Keyboard, M92	as pkbo pointed out correctly boox was not seeing the second ext3 partition. But when the first partition is fat32 it auto mounts it and recognizes the ext3 partition. I don't know more - I'm just a noob. So I'm not saying it must be FAT32 but it works for me. - maybe it works because this time I did it with fdisk instead of grub.. fdisk is not available on boox. Preparing SD card is much easier and faster on pc.

07-10-2013, 05:57 AM	#17
pkbo Addict Posts: 251 Karma: 214890 Join Date: Sep 2006 Device: none	@crazydog great, you did it! Can you post here output of fdisk -l [whatever device corresponds to your sd card]?

07-10-2013, 06:17 AM	#18
crazydog error Posts: 54 Karma: 5810 Join Date: Jan 2012 Device: Kindle Keyboard, M92	seaniko7 opened a new world to ebook reader. fantastic @pkbo: output of fdisk (SD Card) Disk /dev/sdc: 7948 MB, 7948206080 bytes 245 heads, 62 sectors/track, 1021 cylinders, total 15523840 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004f64f Device Boot Start End Blocks Id System /dev/sdc1 2048 4194303 2096128 b W95 FAT32 /dev/sdc2 4194304 15523839 5664768 83 Linux

07-10-2013, 07:20 AM	#20
crazydog error Posts: 54 Karma: 5810 Join Date: Jan 2012 Device: Kindle Keyboard, M92	@por fdisk /dev/sdx --where x is the sd card m prints the help commant (really helpful) n creates new partition then you have to set the size, I set it with +xxxx where x is the number of sectors then you have to format it... and repeat that to create a second partition tar -pxjvf is the command i used to extract the rootfs (where p is needed to preserve permissions) I hope I could help you a bit.

07-10-2013, 11:57 AM	#21
gamba66 Zealot Posts: 114 Karma: 1200000 Join Date: May 2013 Device: Hanvon E920	Can anyone film this and put this on youtube? Not only to gain attention but also because I would like to see this And is there any practical use or will there be? Must be cool to run linux but in the end it runs on an e-ink display

07-10-2013, 01:41 PM	#22
rogerpiano Connoisseur Posts: 59 Karma: 12 Join Date: Nov 2012 Location: Italy Device: Sony PRS 650, Onyx Boox M92, Onyx Boox Max2	hello to all. I am following with great attention the developments of the discussion. I'm a non-expert user of linux and I know that seaniko7 said that for now ported to ubuntu is recommended for expert users. I though I would try, as I think many, and I tried to merge the instructions of seaniko7 with the advice of CrazyDdog to get a more detailed procedure possible. I hope seaniko7 or CrazyDog can control this procedure and give the ok. for me to point 4 is still unclear. thank you very much, I look forward ... 1 - Download uImage-initramfs from: https://github.com/intromatyk/public_kernel/tree/iMX508 1.1??? - Copy the file uimage-initramfs in internal memory of boox (is my personal interpretation) 2 - Flash uImage-initramfs using dd command with betty boox terminal emulator : dd if=/media/flash/update/uImage-initramfs of=/dev/mmcblk0 bs=512 seek=12288 3 - Download current rootfs from: https://www.dropbox.com/s/n50udy9rki...060713.tar.bz2 4 - Format SD and create two ext3 partitions I formatted the first partition on sd card as fat32 - the second as ext3. I did it with fdisk instead of grub. fdisk /dev/sdx --where x is the sd card m prints the help commant (really helpful) n creates new partition then you have to set the size, I set it with +xxxx where x is the number of sectors then you have to format it... and repeat that to create a second partition is this operation in boox with betty boox or in windows?? 5 - Unpack rootfs on second partition preserving permissions and symbolic links tar -pxjvf (with betty boox, is my personal interpretation) 6 - Boot OS using update procedure (i.e. reboot holding Back button)

07-10-2013, 02:26 PM	#23
Feher Addict Posts: 248 Karma: 1502286 Join Date: Jan 2013 Device: Onyx Boox M92; Onyx Boox i86ML; Kobo Aura H2O; Dasung Paperlike	Awesome Work seaniko. I am a noob, so i cannot try this. I want to know one thing - How is the refresh rate in Obuntu. Is something like No-Refresh possible?

07-11-2013, 01:18 AM	#25
underscore Addict Posts: 314 Karma: 1093858 Join Date: Mar 2013 Location: Romania (but i'm italian) Device: Onyx Boox Nova 2, Kingrow K1 (former N96 ML/i86ML Plus/M92)	i made a quick tour on my m92 using https://www.mobileread.com/forums/sho...89&postcount=5 i can see that the main disk is called /dev/mmcblk0 and it's splitted on tre linux partition (id=83) mounted a /, /root and /media/flash The other disk being the external sd card. So basically overwriting with dd the provided uImage-initramfs to /dev/mmcblk0 must be done as root and is a potential brick of the device. I would like to mount -o loop the provided dd image on a linux machine on a mount point but i was not able. Maybe my command is not correct. mount -o loop,offset=32256 uImage-initramfs /tmp/ i have back mount: unknown filesystem type '(null)' i will feel more reassured if i can see the difference between the image and my current artatech system. Maybe with a different tar archive for each of the 3 file systems to overwrite.

07-11-2013, 08:54 AM	#27
crazydog error Posts: 54 Karma: 5810 Join Date: Jan 2012 Device: Kindle Keyboard, M92	M92 Obuntu using Synaptic to install Software https://www.dropbox.com/s/6z0egtjzcr...u_Synaptic.mp4 M92 Obuntu Midori Browser https://www.dropbox.com/s/h86kwple40...ntu_Midori.mp4 M92 playing video https://www.dropbox.com/s/l3wdlcc7kh...Bunny_480p.mp4

07-12-2013, 04:07 AM	#28
underscore Addict Posts: 314 Karma: 1093858 Join Date: Mar 2013 Location: Romania (but i'm italian) Device: Onyx Boox Nova 2, Kingrow K1 (former N96 ML/i86ML Plus/M92)	Thx for the videos! Impressive the movie on e-ink. Obuntu looks pretty fast. Is the joystick usable as well? The plan is to browse documents in a folder and double click them to read, exactly how we are used to use the reader :-)

07-12-2013, 04:21 AM	#29
seaniko7 wannabe developer Posts: 192 Karma: 156548 Join Date: Mar 2011 Device: Kindle: 2xKeyboard, Classic, 2xTouch, 2xPW, PW2; Onyx: Boox M92	@underscore, all keys are usable, but I haven't mapped them yet. For now only "Enter" works out-of-the-box. Now I'm writing initramfs based bootloader, then I'll focus on further development of system image.

07-12-2013, 09:26 AM	#30
lunohod OpenInkpot developer Posts: 211 Karma: 5627 Join Date: Mar 2008 Location: Stuttgart, Germany Device: N516,V3,PRS505,iLiad,eSlick,E60,K3,K4NT,M90,PB912,KoboMini	@seaniko7 Will you publish the screen_updater source code?