Noob's guide to debricking through ATK :D

[knc1]

Originally Posted by term1nat0r

Unfortunately, I did not find it there
Some people describe the same problem. Find another Kindle and recovered from it. But the dump from working Kindla not spread...
And I have no possibility to get another Kindle

First of all, what you ask for is mmcblk0 image - -
Which would be the entire flash device image, including device specific information and personal information.
Sorry - we don't do that.

What you will find is the images of the various partitions on the device all linked on off-site index pages.
(A requirement of this site when copyrighted material is concerned.)

First post, scroll down, section: References and Links, sub-section: Kindle Debricking Images -
There you will find links to the off site index pages of the images available.

They really are there.

[hawhill]

Yes, that worked fine for him already, I think. The only piece missing is the device specific information. And I don't see why anyone should light-heartedly present their own data for this - agreedly - noble cause.

term1nat0r: What you would need to do now is:
- dump the part of the flash that holds the device specific information
- restore sensible values with a hex editor
- write the changed data back to flash.

You need to dump 0x400 Bytes (1kByte), starting at position 0x00040c00.

The first 16 bytes are the serial number (ASCII encoded), 12 Bytes starting at offset 88 (decimal) represent the MAC address (ASCII-encoded again, here it's the Wifi-MAC, I don't have a 3G unit to test).

Note that serial number and MAC are stored in a special section of the Flash which is _not_ part of any partition. No need to dump the whole device, though. See the exact offset/length I cited above in this post.

[twobob]

Waboom. : D

you d man

[hawhill]

Short addendum: I could introduce a "serial and MAC changer" into k3flasher - but won't have time for that any time soon, unfortunately. But when I finally get to do it, I'd be glad if I could add WAN MAC address data, too - I need to dig into the scripts in the firmware to see what they store where in there.

A bit off-topic here, since this is about ATK, not k3flasher.

[Wibber]

Originally Posted by hawhill

Yes, that worked fine for him already, I think. The only piece missing is the device specific information. And I don't see why anyone should light-heartedly present their own data for this - agreedly - noble cause.

term1nat0r: What you would need to do now is:
- dump the part of the flash that holds the device specific information
- restore sensible values with a hex editor
- write the changed data back to flash.

You need to dump 0x400 Bytes (1kByte), starting at position 0x00040c00.

The first 16 bytes are the serial number (ASCII encoded), 12 Bytes starting at offset 88 (decimal) represent the MAC address (ASCII-encoded again, here it's the Wifi-MAC, I don't have a 3G unit to test).

Note that serial number and MAC are stored in a special section of the Flash which is _not_ part of any partition. No need to dump the whole device, though. See the exact offset/length I cited above in this post.

Awesome, thanks man I think this is what I needed!

Hopefully I didn't overwrite the original serial!

So I can do this with K3flasher?

Cheers

[hawhill]

You can do this with ATK or k3flasher. k3flasher might have a direct-edit mode in the future - though not yet, not soon. Plus there are valid reasons to not make it too easy to modify serial numbers and MAC addresses. They do have misuse potential, especially in the light of Amazon blacklisting devices based on serial number (not entirely sure if they do, though)...

[term1nat0r]

Finally I did it!
Thanks a lot to all who helped me in solving my problem! First is: hawhill, knc1, geekmaster, twobob and many others whose messages I have used.
Wi-fi works, the serial number on a place
Here are just a Kindle had to register offline. I suspect that the blame for the SSL certificate that is in the 411 is MISSED.

May suggest what can be done with this?
This certificate is not private information?

[twobob]

I am glad to hear it.

My apologes but I dont quite understand the final problem.

So it IS registered or it IS NOT registered?

Thanks

[term1nat0r]

Originally Posted by twobob

I am glad to hear it.

My apologes but I dont quite understand the final problem.

So it IS registered or it IS NOT registered?

Thanks

I used a hack to cheat Kindl and he thought that it was registered.
In reality, when you try to register, Kindle can not connect to the site and said that it is possible wi-fi does not work. But I have seen information that this certificate is responsible for establishing an SSL connection to be happening that registration.

[knc1]

Start over with a known good pair of factory images for both the systems (your Kindle is a 'dual boot' machine).

Until you do that, you are just wasting your time.

[twobob]

Originally Posted by term1nat0r

I used a hack to cheat Kindl and he thought that it was registered.
In reality, when you try to register, Kindle can not connect to the site and said that it is possible wi-fi does not work. But I have seen information that this certificate is responsible for establishing an SSL connection to be happening that registration.

Ah right yeah I vaguely remember this.

Hmm. some file or another is made by the amazon people as you say If I Recall Correctly.

You have fixed the troublesome required missing data areas.

I would simply overwrite the main partition and the MATCHING kernel at this point.

You should be good to then register it like everyone else assuming you got the details correct, at which point that file will be generated IIRC.

K3 SO still have 3g right? Yeah sure they do, for the adverts.. So just overwrite the current "mangled mess" with fresh.

I would do that. what you do is up to you. I would do that.

[CaelThunderwing]

sorry term1nat0r i havent been aroun din awhile. i can only say if you Still cant get your Kindle to Register. (if thats whats goin on) just press on amazon's Heals. its how they finally got to replacing my unit.

the orginal issue you referance din PM my K3 was an Wifi Only with SO unit. i made teh mistake of NOT backing up devid. (i still suggest so we dont have anyone else making this same mistake) that add in the guide to backup devid before doing anything.

and as well im not super sure but while i tried before i sent out the Dead K3, i tried adding in manually the missing certs.. still nada. the only thing missing at that point that wasnt letting the dead unit register, it still had a garbled "Manufacturing ID" (which in diags it listed as some garblygook..)

[chronosxiii]

My Kindle 3 WiFi keeps freezing, I reboot it 10x times and nothing changed.
I tried factory reset and nothing changed either.
It all started after I installed Sudokan, after a few days of that - it kept freezing and there was no way to make it work.
Now it randomly freezes and reboot itself, is anyone here an expert and has a few spare minute to guide me on a solution path, through PM, directly reply, IRC or anything else!

Much appreciated

[knc1]

The always #1 question:

Is the battery fully re-charged?
Make sure, leave on charger over-night at least.

Then see if that makes a difference.

If it doesn't - then install the KUAL launcher and I'll post a button to give you a battery status report - which should report its current capacity (which might be very low now).

[twobob]

Sudokan?

or Duokan?

I would grab a k3flasher copy.

install that. put it in WAITING FOR DEVICE MODE (like it says clearly in the README for k3flasher)

jump into the right mode via HOLD DOWN POWER + -Vol then release power, then -vol

And go from there.

Check the debricking threads.

basically I am suggesting you HOSE duokan out of existence.

if that is not a solution you wish to hear I am right out of them.

Hope that helps.


You could try the DUOKAN thread also for tips.