PW Cant access fastboot mode

[Asdika]

Hi!

I have a bootlooping kinlde PW and I'm trying to unbrick it using Santactic's methode https://www.mobileread.com/forums/sh...d.php?t=359315 , but when i try to get into fastboot mode it is only shows the voltage of the battery over and over, and i am not able to run any command.

uboot > bist fastboot


U-Boot 2009.08-lab126 (Sep 28 2012 - 14:28:00)

CPU:   Freescale i.MX50 family 1.1V at 800 MHz
mx50 pll1: 800MHz
mx50 pll2: 400MHz
mx50 pll3: 216MHz
ipg clock     : 66666666Hz
ipg per clock : 66666666Hz
uart clock    : 24000000Hz
cspi clock    : 54000000Hz
ahb clock     : 133333333Hz
axi_a clock   : 400000000Hz
axi_b clock   : 200000000Hz
weim_clock    : 100000000Hz
ddr clock     : 266666666Hz
esdhc1 clock  : 80000000Hz
esdhc2 clock  : 80000000Hz
esdhc3 clock  : 80000000Hz
esdhc4 clock  : 80000000Hz
MMC:  FSL_ESDHC: 0, FSL_ESDHC: 1
Board: Celeste (256 MB)
Boot Reason: [POR]
Boot Device: MMC
Board Id: 015138206XS
S/N: B01
I2C:   ready
DRAM:  256 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
POST done in 2 ms
Battery voltage: 4021 mV

running cmd: fastboot
Entering fastboot mode...
Battery voltage: 4026 mV
USB speed: HIGH
Connected to USB host!
USB configured.
Battery voltage: 4129 mV
Battery voltage: 4138 mV

I have already Erased MMC!
Do you have any ideas what could be the problem?

This what I see when I normally let the system to run:

In:    serial
Out:   logbuff
Err:   logbuff
Quick Memory Test 0x70000000, 0xfffe000
POST done in 17 ms
Hit any key to stop autoboot:  0
## Booting kernel from Legacy Image at 70800000 ...
   Image Name:   Linux-2.6.31-rt11-lab126
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4608576 Bytes =  4.4 MB
   Load Address: 70008000
   Entry Point:  70008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
Starting kernel ...
2.6.31-rt11-lab126 #1 Fri Sep 28 14:59:26 PDT 2012 armv7l
INFO:Loaded module /lib/modules/eink_fb_waveform.ko  (38984 bytes)
INFO:Loaded module /lib/modules/mxc_epdc_fb.ko default_panel_hw_init=1 default_update_mode=1 (51140 bytes)
INFO:eink initialized... (786432 bytes)
Press [ENTER] for recovery menu...       0 /INFO:!!! Checking MBR /dev/mmcblk0 !!!!
INFO:partition 2, start sector is 782336
INFO:partition 3, start sector is 913408
INFO:partition 4, start sector is 1044480
INFO:maximizing partition 2863104 sectors
INFO:*** Partition table verified for /dev/mmcblk0 ***
INFO:Checking for updates... (auto-pilot mode)
/dev/mmcblk0p4:
CHS=4/16/44736 size=1465909248 bytes
flag type      first       last  lba first   lba size
Partition p1:
0x00 0x0b         16 <large>            16    2863088
    CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
INFO:Setup loop device /dev/loop0 for /dev/mmcblk0p4 + 8192
INFO:No update*.bin found; no update needed.
INFO:no updates found.
BOOTING DEFAULT.
  argc == 11
  argv[0]: "kinit"
  argv[1]: "consoleblank=0"
  argv[2]: "rootwait"
  argv[3]: "ro"
  argv[4]: "ip=off"
  argv[5]: "root=/dev/mmcblk0p1"
  argv[6]: "quiet"
  argv[7]: "eink=fslepdc"
  argv[8]: "video=mxcepdcfb:E60,bpp=8,x_mem=4M"
  argv[9]: "mem=256M"
  argv[10]: "console=ttymxc0,115200"
  argc == 4
  argv[0]: "IP-Config"
  argv[1]: "-i"
  argv[2]: "Linux kinit"
  argv[3]: "ip=off"
IP-Config: no devices to configure
kinit: do_mounts
kinit: name_to_dev_t(/dev/mmcblk0p1) = dev(179,1)
kinit: root_dev = dev(179,1)
kinit: /dev/root appears to be a ext3 filesystem
kinit: trying to mount /dev/root on /root with type ext3
kinit: Mounted root (ext3 filesystem) readonly.
info system:emiting_event:mounted_proc:
info system:emiting_event:mounted_sys:
info system:emiting_event:mounted_dev:
info system:emiting_event:mounted_tmpfs:
info milestone:5.39:sy50:
init.exe: recevent pre-start process (496) terminated with status 1
info system:start:time=5410:
info system:config:platform=yoshime3,board=celeste,rev=21,proto=N,wifi=Y,wan=Y:
info milestone:5.62:sy51:
info milestone:6.26:sy99:
info system:done:time=6290:
info system_cramfs_loopbacks:mountingcramfs:Mounting compressed directories filesystem images:
info system_cramfs_loopbacks:mounted:Image /lib/firmware/cyttsp.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/share/X11/xkb.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/java/lib/fonts.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /etc/kdb.src.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/lib/locale.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/share/keyboard.cramfs.img mounted:
info system:emiting_event:mounted_cramfs_loopbacks:
info milestone:6.92:fs75:
info system:emiting_event:loaded_modules_dependencies:
info modules:modprobe:loading module g_file_storage:
info system:emiting_event:loaded_g_file_storage:
info modules:modprobe:loading module fuse:
info system:emiting_event:loaded_fuse:
info modules:modprobe:loading module mwan:
info milestone:7.29:fs00:
info system:emiting_event:loaded_mwan:



Welcome to Kindle!

kindle login: info modules:modprobe:loading module ppp_async:
info system:emiting_event:loaded_ppp_async:
info system:emiting_event:loaded_fakekey:
info system:emiting_event:mounted_varLocal:
info milestone:7.56:fs25:
info milestone:7.60:vi00:
info display:update:Displaying splash screen:
info milestone:7.95:vi99:
info display:started:time=7960:
info system:emiting_event:display_ready:
info userstore:run:time=8200,action=start:
info battery:charged:cap=89,mV=4086,mAH=647:
info system:emiting_event:battery_ready:
info cyttsp:update:vendor=CANDO:
info system:emiting_event:loaded_touch:
info system:emiting_event:mounted_userstore:
info milestone:10.53:fs50:
info milestone:10.55:fs90:
info milestone:10.58:fs99:
info milestone:10.61:sys99:
info system:emiting_event:dbus_ready:
info dbus:check-update:status=2:dbus_ready sent
info wan:info:type=4,version=ELMO_04_04_00:
info wand.conf:::wan start script complete
info milestone:11.96:xx00:
info X:load:time=12050:
info X:xorg.conf:Generating xorg.conf:
info X:makexconfig:Celeste Input device detection status:
info X:makexconfig:Touch device: OK:
info X:makexconfig:Accelerometer device: N/A !!:
info X:xorg.conf:xorg.conf generated:
info milestone:12.81:xx50:
info X:starting:time=12840:
info x_monitor:x_monitor starts::
info wifim:enablediv:enabling antenna diversity for wifi...:
info x_monitor:read_counters::REBOOTS=0, RESTART=0, REBOOT_LIMIT=1, RESTART_LIMIT=5

I tried to EXPORT FAT and I could copy an update.bin to it then press U "Update usin update*.bin file on FAT partition" , but it did nothing.