1)At first I had to download the correct Firmware for my device (In my case it was "factory_KT3_5.8.0_initial.bin" )
2)Then I renamed it to update.bin (necessary in a later step) and put it to the root directory of my kindle
4) I startet the device and interrupted the booting sequence by pressing the "enter" button to get into uboot
6)After the diagnostics mode was fully loaded I pressed enter to get into kindle Login
9)Now in the boot sequence there was an entry to get into recovery mode. It was shown up just for about 1 second. When this entry was shown I had to press "enter" to get into this mode.
10) Now I got into recovery mode.
11) Here I had 10 seconds time to choose one of the operations.
Code:
U-Boot 2014.04 (Jan 24 2018 - 12:41:30)
CPU: Freescale i.MX6SL rev1.3 at 792 MHz
CPU: Temperature 39 C, calibration data: 0x58d50a5f
Reset cause: POR
FRED::: EXTCSD177=0, 179=48FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Board: Heisenberg
Board Id: P00118077373003J
S/N: G000K905738108UK
I2C: ready
DRAM: MR5=0x1,MR6=0x4 512 MiB
WARNING: Caches not enabled
MMC:
FRED::: EXTCSD177=0, 179=48FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
REBOOTMODE: 0
using default bootcmdNormal Boot
Hit any key to stop autoboot: 0
uboot >
uboot >
uboot > run diags_boot
run diags_boot
BOOTing diags from mmc ...
mmc1(part 0) is current device
MMC read: dev # 1, block # 29392, count 28672 ... 28672 blocks read in 319 msec: OK
MMC read: dev # 1, block # 29192, count 256 ... 256 blocks read in 6 msec: OK
## Booting kernel from Legacy Image at 80800000 ...
Image Name: Linux-3.10.53-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4788336 Bytes = 4.6 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
## Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Loading Kernel Image ...
OK
Loading Device Tree to 9fcae000, end 9fcb85ef ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting
Linux on physical CPU 0x0
[ 0.000000] Linux version 3.10.53-lab126 (jenkins-official@sjc10-jbuild07) (collect2: error: ld returned 1 exit status) #1 PREEMPT Fri Jul 22 00:45:40 PDT 2016
[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Freescale i.MX6 SoloLite (Device Tree), model: Heisenberg P0
[ 0.000000] printk_reserve_buf:863 log_goal_location:0x8fff0000 log_worst_location:0x8fef0000 new_log_buf_len:32768
[ 0.000000] printk_reserve_buf:883 printk log placed at 8fff0000
[ 0.000000] cma: CMA: reserved 32 MiB at 9c000000
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw
[ 0.000000] Prink buffer will be relocated to physical address: 8fff0000 va: 00000000 new_log_buf_len:32768
[ 0.000000] Prink buffer will be relocated to physical address: 8fff0000 va: 8fff0000 new_log_buf_len:32768
[ 0.000000] log_buf_len: 32768
[ 0.000000] early log buf free: 30776(93%)
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 512MB = 512MB total
[ 0.000000] Memory: 477600k/477600k available, 46688k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xa0800000 - 0xff000000 (1512 MB)
lowmem : 0x80000000 - 0xa0000000 ( 512 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
.text : 0x80008000 - 0x807187c4 (7234 kB)
.init : 0x80719000 - 0x80882b7c (1447 kB)
.data : 0x80884000 - 0x808c9e80 ( 280 kB)
.bss : 0x808c9e80 - 0x808f29c8 ( 163 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x32030000, Cache size: 262144 B
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000465] Calibrating delay loop... 789.70 BogoMIPS (lpj=3948544)
[ 0.040130] pid_max: default: 32768 minimum: 301
[ 0.040271] Mount-cache hash table entries: 512
[ 0.044669] CPU: Testing write buffer coherency: ok
[ 0.044893] Setting up static identity map for 0x80524338 - 0x80524390
[ 0.045673] devtmpfs: initialized
[ 0.047389] pinctrl core: initialized pinctrl subsystem
[ 0.047639] regulator-dummy: no parameters
[ 0.049758] NET: Registered protocol family 16
[ 0.057114] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.057697] LAB126 Board id - P00118077373003J
[ 0.057777] Use WDOG1 as reset source
[ 0.063223] syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered
[ 0.063475] vdd1p1: 800 <--> 1375 mV at 1100 mV
[ 0.063761] vdd3p0: 2625 <--> 3400 mV at 3000 mV
[ 0.064056] vdd2p5: 2100 <--> 2850 mV at 2500 mV
[ 0.064414] cpu: 725 <--> 1450 mV at 1100 mV
[ 0.064688] vddpu: 725 <--> 1450 mV
[ 0.065047] vddsoc: 725 <--> 1450 mV at 1175 mV
[ 0.066912] syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered
[ 0.068957] syscon 21bc000.ocotp-ctrl: regmap [mem 0x021bc000-0x021bffff] registered
[ 0.070830] amp_boost_enable:iMX:MAX98090:BOARD
[ 0.070861
] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.070871] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.074153] imx6sl-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[ 0.079182] bio: create slab <bio-0> at 0
[ 0.080362] SCSI subsystem initialized
[ 0.080584] usbcore: registered new interface driver usbfs
[ 0.080650] usbcore: registered new interface driver hub
[ 0.080766] usbcore: registered new device driver usb
[ 0.082107] bd7181x 0-004b: IRQ 276 GPIO 116
[ 0.087661] buck1: 800 <--> 2000 mV at 1300 mV
[ 0.088852] buck2: 800 <--> 2000 mV at 1300 mV
[ 0.089686] buck3: 1200 <--> 2700 mV at 1800 mV
[ 0.090498] buck4: 1100 <--> 1850 mV at 1200 mV
[ 0.091298] buck5: 1800 <--> 3300 mV at 3200 mV
[ 0.092123] ldo1: 800 <--> 3300 mV at 3200 mV
[ 0.092917] ldo2: 800 <--> 3300 mV at 3200 mV
[ 0.094149] ldo3: 3000 mV
[ 0.094767] ldo4: 800 <--> 3300 mV at 3200 mV
[ 0.095351] ldo5: 800 <--> 3300 mV at 1800 mV
[ 0.095923] dvref: 3000 mV
[ 0.096061] lpsr: 1800 mV
[ 0.096648] wled: at 0 mV 0 <--> 25 mA at 0 mA
[ 0.097529] i2c i2c-0: IMX I2C adapter registered
[ 0.098144] i2c i2c-1: IMX I2C adapter registered
[ 0.098418] i2c i2c-2: IMX I2C adapter registered
[ 0.098529] pps_core: LinuxPPS API ver. 1 registered
[ 0.098540] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.098565] PTP clock support registered
[ 0.098911] MIPI CSI2 driver module loaded
[ 0.098996] Advanced Linux Sound Architecture Driver Initialized.
[ 0.099619] cfg80211: Calling CRDA to update world regulatory domain
[ 0.099653] cfg80211: World regulatory domain updated:
[ 0.099663] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 0.099674] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 0.099684] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 0.099693] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 0.099702] cfg80211: (5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 0.099711] cfg80211: (5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 0.100890] pureg-dummy: no parameters
[ 0.101518] Switching to clocksource mxc_timer1
[ 0.109429] NET: Registered protocol family 2
[ 0.110106] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.110191] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.110316] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.110372] TCP: reno registered
[ 0.110388] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.110407] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.110613] NET: Registered protocol family 1
[ 0.110874] RPC: Registered named UNIX socket transport module.
[ 0.110886] RPC: Registered udp transport module.
[ 0.110895] RPC: Registered tcp transport module.
[ 0.110903] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.117398] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.118023] ldo2p5-dummy: no parameters
[ 0.118756] Bus freq driver module loaded
[ 0.119199] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.124565] VFS: Disk quotas dquot_6.5.2
[ 0.124710] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.127007] NFS: Registering the id_resolver key type
[ 0.127047] Key type id_resolver registered
[ 0.127057] Key type id_legacy registered
[ 0.127098] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.127609] msgmni has been set to 996
[ 0.130577] io scheduler noop registered
[ 0.130591] io scheduler deadline registered
[ 0.130634] io scheduler cfq registered (default)
[ 0.137456] Serial: IMX
driver
[ 0.137778] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
[ 0.840918] console [ttymxc0] enabled
[ 0.845077] 2034000.serial: ttymxc2 at MMIO 0x2034000 (irq = 60) is a IMX
[ 0.852302] imx6sl-pinctrl 20e0000.iomuxc: pin MX6SL_PAD_SD1_DAT4 already requested by 20e0000.iomuxc; cannot claim for 2038000.serial
[ 0.864454] imx6sl-pinctrl 20e0000.iomuxc: pin-145 (2038000.serial) status -22
[ 0.871724] imx6sl-pinctrl 20e0000.iomuxc: could not request pin 145 on device 20e0000.iomuxc
[ 0.880277] imx-uart 2038000.serial: Error applying setting, reverse things back
[ 0.887778] 2038000.serial: ttymxc3 at MMIO 0x2038000 (irq = 61) is a IMX
[ 0.895120] serial: Freescale lpuart driver
[ 0.900211] Registering Heisenberg hall sensor platform device
[ 0.907305] imx sema4 driver is registered.
[ 0.916484] brd: module loaded
[ 0.922285] loop: module loaded
bt_pwrctrl_init called..
[ 0.927847]
bt_reset pin obtained is 51
[ 0.932134]
bt_dev_wake pin obtained is 138
[ 0.936520]
bt_host_wake pin obtained is 93
[ 0.940912] IRQ# for BT HOST WAKE: 253
bt_pwrctrl_probe probe successful
[ 0.949852] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.956731] usbcore: registered new interface driver usb-storage
[ 0.963767] imx6sl-pinctrl 20e0000.iomuxc: pin MX6SL_PAD_EPDC_PWRCOM already requested by 20e0000.iomuxc; cannot claim for 2184000.usb
[ 0.975926] imx6sl-pinctrl 20e0000.iomuxc: pin-56 (2184000.usb) status -22
[ 0.982849] imx6sl-pinctrl 20e0000.iomuxc: could not request pin 56 on device 20e0000.iomuxc
[ 0.991316] imx_usb 2184000.usb: Error applying setting, reverse things back
[ 1.002623] usb_gadget_state_work: gadget state: not attached
[
1.451574] imx_usb 2184000.usb: vbus is error
[ 1.456035] imx_usb 2184000.usb: Error occurs during detection: -22
[ 1.462814] mousedev: PS/2 mouse device common for all mice
[ 1.474390] bd7181x-rtc bd7181x-rtc: rtc core: registered bd7181x-rtc as rtc0
[ 1.482095] snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc1
[ 1.490485] i2c /dev entries driver
[ 1.494580] bd7181x-power bd7181x-power: battery_cycle = 0
[ 1.500703] Status Register 1 == 0x0
[ 1.504742] Status Register 2 == 0x0
[ 1.508741] Status Register 3 == 0x40
[ 1.512845] Status Register 4 == 0x0
[ 1.516844] Status Register 5 == 0x80
[ 1.520926] Status Register 6 == 0x0
[ 1.524943] Status Register 7 == 0x0
[ 1.528938] Status Register 8 == 0x2
[ 1.532951] Status Register 9 == 0x0
[ 1.536948] Status Register 10 == 0x0
[ 1.541032] Status Register 11 == 0x0
[ 1.545133] Status Register 12 == 0x0
[ 1.551723] errflags = 1
[ 1.554264] bit0 is set
[RESET REASONS]: SOFTWARE_RESTART: Software Initiated System Restart
[ 1.579455] imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0) imx2_wdt.base=0xa0920000 base pa:0x20bc000 imx2_wdt.clk=0x9a00c100
[ 1.594224] cpuidle: using governor ladder
[ 1.598350] cpuidle: using governor menu
[ 1.602447] sdhci: Secure Digital Host Controller Interface driver
[ 1.608650] sdhci: Copyright(c) Pierre Ossman
[ 1.613046] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.623700] mmc1: no vqmmc regulator found
[ 1.627811] mmc1: Not allowing HS200
[ 1.631397] mmc1: no vmmc regulator found
[ 1.681574] mmc1: SDHCI controller on 2190000.usdhc [2190000.usdhc] using DMA
[ 1.692212] mmc0: no vqmmc regulator found
[ 1.696322] mmc0: Not allowing HS200
[ 1.699908] mmc0: no vmmc regulator found
[ 1.741568] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using DMA
[ 1.750831] usbcore: registered new interface driver usbhid
[ 1.756458] usbhid: USB HID core driver
[ 1.761320] NET: Registered protocol family 26
[ 1.768033] TCP: cubic registered
[ 1.771362] IPv6: Loaded, but administratively disabled, reboot required to enable
[ 1.778986] sit: IPv6 over IPv4 tunneling driver
[ 1.784103] NET: Registered protocol family 17
[ 1.790668] 8021q: 802.1Q VLAN Support v1.8
[ 1.798989] Key type dns_resolver registered
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 1.835816] ldo5: disabling
[ 1.844605] ldo4: disabling
[ 1.847816] regulator-dummy: disabling
[ 1.851822] imx mcc test is registered.
[ 1.856492] bd7181x-rtc bd7181x-rtc: setting system clock to 2001-01-06 22:51:39 UTC (978821499)
[ 1.868952] ALSA device list:
[ 1.874027] No soundcards found.
[ 1.878647] Freeing unused kernel memory: 1444K (80719000 - 80882000)
3.10.53-lab126 #1 PREEMPT Fri Jul 22 00:45:40 PDT 2016 armv7l
[ 2.095862] mmc0: BKOPS_EN bit is not set
[ 2.118099] mmc0: new high speed DDR MMC card at address 0001
[ 2.124179] mmcblk0: mmc0:0001 NJ2ZMB 3.64 GiB
[ 2.128809] mmcblk0boot0: mmc0:0001 NJ2ZMB partition 1 4.00 MiB
[ 2.134851] mmcblk0boot1: mmc0:0001 NJ2ZMB partition 2 4.00 MiB
[ 2.140855] mmcblk0rpmb: mmc0:0001 NJ2ZMB partition 3 512 KiB
[ 2.147344] mmcblk0: p1 p2 p3 p4
[ 2.153286] mmcblk0boot1: unknown partition table
[ 2.159917] mmcblk0boot0: unknown partition table
[ 2.198230] INFO:child exited with status 00000000
[ 2.203576] INFO:find_file:118 Found V220_C283_BDB501_ED060SCSU1_TC.wrf.gz
ERROR:wfm_count=1
[ 2.212560] mxc_epdc_eink: module license 'proprietary' taints kernel.
[ 2.219276] Disabling lock debugging due to kernel taint
[ 2.224992] INFO:Loaded module /lib/modules/mxc_epdc_eink.ko (11172 bytes)
Panel VCOM string: 2690
[ 2.236191] imx_epdc_fb 20f4000.epdc: vcom_steps 125
[ 2.241350] imx_epdc_fb 20f4000.epdc: Memory override detected TotalMem:512M X:800 Y:600 FBMem:6M
[ 2.257336] imx_epdc_fb 20f4000.epdc: EPDC version = 2.1.0
[ 2.324232] wv_file->wdh.luts & 0xC =4
[ 4.164619] INFO:Loaded module /lib/modules/mxc_epdc_fb.ko (79696 bytes)
[ 4.448816] INFO:eink initialized... (486400 bytes)
Press [ENTER] for recovery menu... 0 /[ 4.472283] INFO:!!! Checking MBR /dev/mmcblk0 !!!!
[ 4.485638] INFO:partition 2, start sector is 987136
[ 4.490676] INFO:partition 3, start sector is 1118208
[ 4.495853] INFO:partition 4, start sector is 1249280
[ 4.500957] INFO:maximizing partition 6385664 sectors
[ 4.506057] INFO:*** Partition table verified for /dev/mmcblk0 ***
[ 4.513485] INFO:Loaded module /lib/modules/libcomposite.ko (45712 bytes)
[ 4.521733] g_mass_storage gadget: Mass Storage Function, version: 2009/09/11
[ 4.528879] g_mass_storage gadget: Number of LUNs=1
[ 4.533840] lun0: LUN: removable file: (no medium)
[ 4.538734] fsg_bind:3212
[ 4.541367] g_mass_storage gadget: Internal Storage, version: 2009/09/11
[ 4.548095] g_mass_storage gadget: userspace failed to provide iSerialNumber
[ 4.555158] g_mass_storage gadget: g_mass_storage ready
[ 4.560487] INFO:Loaded module /lib/modules/g_mass_storage.ko removable=1 idVendor=0x1949 idProduct=0x0004 recovery_mode=1 (41120 bytes)
[ 4.854544] usb_gadget_state_work: gadget state: addresssed
[ 4.900895] g_mass_storage gadget: high-speed config #1: Linux File-Backed Storage
[ 4.908516] usb_gadget_state_work: gadget state: configured
[ 4.914121]
send_online_uevent:432 fsg_ 0x0 recovery_mode:1
Charge: 98% [##########################################################]
Menu
====
3. Load MMC0 over USB storage
4. Erase MMC0
I. Initialize Partition Table (fdisk) and format FAT
O. Format and overwrite FAT partition
E. Export FAT partition
U. Update using update*.bin file on FAT partition
M. Update using update*.bin file on FAT partition of second MMC port
D. dmesg / kernel printk ring buffer.
Q. quit
Choose: 10 /
Charge: 98% [##########################################################]
Menu
====
3. Load MMC0 over USB storage
4. Erase MMC0
I. Initialize Partition Table (fdisk) and format FAT
O. Format and overwrite FAT partition
E. Export FAT partition
U. Update using update*.bin file on FAT partition
M. Update using update*.bin file on FAT partition of second MMC port
D. dmesg / kernel printk ring buffer.
Q. quit
Choose: 10 /
Charge: 98% [##########################################################]
Menu
====
3. Load MMC0 over USB storage
4. Erase MMC0
I. Initialize Partition Table (fdisk) and format FAT
O. Format and overwrite FAT partition
E. Export FAT partition
U. Update using update*.bin file on FAT partition
M. Update using update*.bin file on FAT partition of second MMC port
D. dmesg / kernel printk ring buffer.
Q. quit
Choose: 10 /
Charge: 98% [##########################################################]
Menu
====
3. Load MMC0 over USB storage
4. Erase MMC0
I. Initialize Partition Table (fdisk) and format FAT
O. Format and overwrite FAT partition
E. Export FAT partition
U. Update using update*.bin file on FAT partition
M. Update using update*.bin file on FAT partition of second MMC port
D. dmesg / kernel printk ring buffer.
Q. quit
Choose: 10 /
Charge: 98% [##########################################################]
Menu
====
3. Load MMC0 over USB storage
4. Erase MMC0
I. Initialize Partition Table (fdisk) and format FAT
O. Format and overwrite FAT partition
E. Export FAT partition
U. Update using update*.bin file on FAT partition
M. Update using update*.bin file on FAT partition of second MMC port
D. dmesg / kernel printk ring buffer.
Q. quit
Choose: 10 /
Charge: 98% [##########################################################]
Menu
====
3. Load MMC0 over USB storage
4. Erase MMC0
I. Initialize Partition Table (fdisk) and format FAT
O. Format and overwrite FAT partition
E. Export FAT partition
U. Update using update*.bin file on FAT partition
M. Update using update*.bin file on FAT partition of second MMC port
D. dmesg / kernel printk ring buffer.
Q. quit
Choose: 10 /
Charge: 98% [##########################################################]
Menu
====
3. Load MMC0 over USB storage
4. Erase MMC0
I. Initialize Partition Table (fdisk) and format FAT
O. Format and overwrite FAT partition
E. Export FAT partition
U. Update using update*.bin file on FAT partition
M. Update using update*.bin file on FAT partition of second MMC port
D. dmesg / kernel printk ring buffer.
Q. quit
Choose: 10 /
Charge: 98% [##########################################################]
Menu
====
3. Load MMC0 over USB storage
4. Erase MMC0
I. Initialize Partition Table (fdisk) and format FAT
O. Format and overwrite FAT partition
E. Export FAT partition
U. Update using update*.bin file on FAT partition
M. Update using update*.bin file on FAT partition of second MMC port
D. dmesg / kernel printk ring buffer.
Q. quit
Choose: 5 -
Charge: 98% [##########################################################]
Menu
====
3. Load MMC0 over USB storage
4. Erase MMC0
I. Initialize Partition Table (fdisk) and format FAT
O. Format and overwrite FAT partition
E. Export FAT partition
U. Update using update*.bin file on FAT partition
M. Update using update*.bin file on FAT partition of second MMC port
D. dmesg / kernel printk ring buffer.
Q. quit
Choose: 8 \
Charge: 98% [##########################################################]
Menu
====
3. Load MMC0 over USB storage
4. Erase MMC0
I. Initialize Partition Table (fdisk) and format FAT
O. Format and overwrite FAT partition
E. Export FAT partition
U. Update using update*.bin file on FAT partition
M. Update using update*.bin file on FAT partition of second MMC port
D. dmesg / kernel printk ring buffer.
Q. quit
Choose: 7 |
Charge: 98% [##########################################################]
Menu
====
3. Load MMC0 over USB storage
4. Erase MMC0
I. Initialize Partition Table (fdisk) and format FAT
O. Format and overwrite FAT partition
E. Export FAT partition
U. Update using update*.bin file on FAT partition
M. Update using update*.bin file on FAT partition of second MMC port
D. dmesg / kernel printk ring buffer.
Q. quit
Choose: 7 |u
uu
/dev/mmcblk0p4:
CHS=4/16/99776 size=3269459968[ 21.333659] INFO:Setup loop device /dev/loop0 for /dev/mmcblk0p4 + 8192
bytes
flag type first last lba first lba size
Pa[ 21.346160] FAT-fs (loop0): Volume was not safely ejected. Run fsck to correct.
rtition p1:
0x00 0x0b 16[ 21.356693] INFO:find_file:118 Found update.bin
<large> 16 6385648
CHS: 0/1/1 - <large>
Par[ 21.366385] INFO:Skipping battery charge check
tition p2:
Partition p3:
Partit[ 21.373361] INFO:Found bundle /mnt-us/update.bin
ion p4:
[ 21.380805] INFO:*** NORMAL MODE
[ 21.467619] *** CHECKING /mnt-us/update.bin ***
[ 22.288490] INFO:do_unbundle: filename=/mnt-us/update.bin, new_file=0x0001534c
[ 22.314716] INFO:Unsigned bundle.
[ 22.335159] IGNORING FILE: update-J8-heisenberg_eanab-044.dat
update-J8-heisenberg_eanab-044.dat:128 6d4333bf8eb2639a8d84e1eec0c39eb7 imx6sl_heisenberg/u-boot.bin 3 bootloader_bin
1 a862af7d56828c87721fb58e41621b3b imx6sl_heisenberg/uImage 38 main_kernel
128 4357d531d7e5396db90cfe752d7398d7 rootfs.img.gz 1669 update_image_rootfs
128 70783fa7689c34aead7d47a3826dcb9d data.stgz demo_data.stgz voice_data.stgz 4195 update_data_data
update-J8-heisenberg_eanab-044.dat:EOF
[ 22.376364] INFO:Total progress is 1%
imx6sl_heisenberg/u-boot.bin 26CHK: imx6sl_heisenberg/u-boot.bin 1957 [#######################hash for UBoot:
imx6sl_heisenberMD5: g/u-boot.bin 447684 [########6d##############################]
4333bf8eb2639a8d84e1eec0c39eb7
SHA256: 1972c18868b5e1965a4ab727bc0e6cb3ecf75547888cb951b03107ce8afe3276
[ 22.410703] SIGNATURE FILE: imx6sl_heisenberg/u-boot.bin.sig
[ 22.416564] INFO:Total progress is 1%
[ 22.420413] INFO:imx6sl_heisenberg/u-boot.bin.sig:sig_len=256
imx6sl_heisenberg/uImage 4980736 [###########################[ 22.866945] INFO:Total progress is 3%
###########]CHK: imx6sl_heisenberg/uImage
hash for UImage:
MD5: a862af7d56828c87721fb58e41621b3b
SHA256: 4276486b6781af591eff66eb10c2c2243de111c005af3bf4c8e397a1209a53e9
[ 22.889509] SIGNATURE FILE: imx6sl_heisenberg/uImage.sig
[ 22.895023] INFO:Total progress is 3%
[ 22.898870] INFO:imx6sl_heisenberg/uImage.sig:sig_len=256
rootfs.img.gz 218795861 [##############################[ 38.247960] INFO:Total progress is 13%
########]CHK: rootfs.img.gz
hash for RootFS:
MD5: 4357d531d7e5396db90cfe752d7398d7
SHA256: e9eeb676077e3899aec724d5b7e99bf16d6cb561b75f5aebfffb14dda09eb6e7
[ 38.268311] SIGNATURE FILE: rootfs.img.gz.sig
[ 38.272872] INFO:Total progress is 13%
[ 38.276801] INFO:rootfs.img.gz.sig:sig_len=256
data.stgz 549898743 [###############################[ 76.214805] INFO:Total progress is 18%
#######]CHK: data.stgz
hash for Userdata:
MD5: 18dc2c052d78e15edecc7cf283eb9d3f
SHA256: 0b6d55d7efea941f943f9f95e371f1be1b941878b300830af4aabfe32cd791f7
[ 76.234642] SIGNATURE FILE: data.stgz.sig
[ 76.238837] INFO:Total progress is 18%
[ 76.242826] INFO:data.stgz.sig:sig_len=256
[ 76.246953] SIGNATURE FILE: update-J8-heisenberg_eanab-044.dat.sig
[ 76.253313] IGNORING SIGNATURE FILE: update-J8-heisenberg_eanab-044.dat.sig
[ 76.260984] INFO:*** bundle sizes: UImage[4980736 / 14680064], RootFS[460800000 / 471859200], UBoot[447684 / 458752], DiagsFS[0 / 67108864], Diags Kernel[0 / 14680064], Userdata[549898743 / 2212356096], fbios[0 / 0], sbios[0 / 0]
[ 76.282302] ERROR: signature is not the correct length (128 bytes versus 256 bytes)
[ 76.292517] INFO:UImage:Present siglen=256 sigpassed=Yes
[ 76.297881] ERROR: signature is not the correct length (128 bytes versus 256 bytes)
[ 76.308063] INFO:RootFS:Present siglen=256 sigpassed=Yes
[ 76.313457] ERROR: signature is not the correct length (128 bytes versus 256 bytes)
[ 76.323625] INFO:UBoot:Present siglen=256 sigpassed=Yes
[ 76.328856] INFO:DiagsFS:missing
[ 76.332103] INFO:Diags Kernel:missing
[ 76.335813] ERROR: signature is not the correct length (128 bytes versus 256 bytes)
[ 76.345971] INFO:Userdata:Present siglen=256 sigpassed=Yes
[ 76.351462] INFO:fbios:missing
[ 76.354534] INFO:sbios:missing
[ 76.357601] *** UPDATING /mnt-us/update.bin (Attempt #1) ***
[ 76.363321] INFO:do_unbundle: filename=/mnt-us/update.bin, new_file=0x000163fc
[ 76.392269] INFO:Updating imx6sl_heisenberg/u-boot.bin
imx6sl_heisenberg/u-boot.bin 447684 [#######################[ 76.436691] INFO:Total progress is 21%
###############]
[ 76.442688] INFO:imx6sl_heisenberg/u-boot.bin update successful
[ 76.450105] INFO:Updating imx6sl_heisenberg/uImage
imx6sl_heisenberg/uImage 4980736 [###########################[ 76.912438] INFO:Total progress is 23%
###########]
[ 76.918314] INFO:imx6sl_heisenberg/uImage update successful
rootfs.img.gz 218795861 [###############################[ 133.527382] INFO:Total progress is 90%
#######]
[ 133.691268] INFO:rootfs.img.gz update successful
[ 133.696485] INFO:Updating data.stgz
data.stgz 549898743 [######################################][ 241.049088] INFO:Total progress is 100%
[ 241.054174] INFO:data.stgz update successful
[ 241.059096] INFO:Installation had uImage. Installing it.
[ 241.064821] INFO:Copying /uImage to /dev/mmcblk0 ...
4980736 [######################################]
[ 246.049907] INFO:Copying /uboot to /dev/mmcblk0boot0 ...
447684 [ 246.088019] FAT-fs (loop0): Volume was not safely ejected. Run fsck to correct.
[################################[ 246.095624] INFO:removing /mnt-us/update.bin
######]
[ 246.275696] INFO:bundle /mnt-us/update.bin was successful
Charge: 98% [##########################################################]
Menu
====
3. Load MMC0 over USB storage
4. Erase MMC0
I. Initialize Partition Table (fdisk) and format FAT
O. Format and overwrite FAT partition
E. Export FAT partition
U. Update using update*.bin file on FAT partition
M. Update using update*.bin file on FAT partition of second MMC port
D. dmesg / kernel printk ring buffer.
Q. quit
Choose: 1 -
[ 257.474610] fsg_disable:2563
Menu timeout
[ 257.477652]
send_offline_uevent:407 fsg_ 0x2 unsafe 1 recovery_mode:1
[ 257.485469] fsg_unbind:3175
[ 257.488290]
send_offline_uevent:407 fsg_ 0x2 unsafe 1 recovery_mode:1
[ 257.503474] usb_gadget_state_work: gadget state: not attached
[ 257.509414] INFO:storage_shutdown: done with g_mass_storage
[ 257.515193] INFO:storage_shutdown: done with libcomposite
BOOTING DEFAULT.
IP-Config: no devices to configure
[ 258.360567] kjournald starting. Commit interval 5 seconds
[ 258.366265] EXT3-fs (mmcblk0p2): using internal journal
[ 258.372071] EXT3-fs (mmcblk0p2): recovery complete
[ 258.376869] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode
kinit: Mounted root (ext3 filesystem).
init started: BusyBox v1.17.1 (2016-07-22 00:36:46 PDT)
starting pid 89, tty '': '/etc/init.d/rcS'
/etc/init.d/rcS: line 89: boot_milestone: not found
system: I rcS:def:starting /etc/rcS.d/S50diags
USER=root
prevlevel=N
HOME=/
runlevel=S
TERM=vt102
PATH=/sbin:/bin:/usr/sbin:/usr/bin:/usr/local/bin
SHELL=/bin/sh
PWD=/
VERBOSE=no
READ_AHEAD=4
USER=root
prevlevel=N
HOME=/
runlevel=S
TERM=vt102
PATH=/sbin:/bin:/usr/sbin:/usr/bin:/usr/local/bin
SHELL=/bin/sh
PWD=/
VERBOSE=no
IO_SCHED=anticipatory
USER=root
prevlevel=N
HOME=/
runlevel=S
TERM=vt102
PATH=/sbin:/bin:/usr/sbin:/usr/bin:/usr/local/bin
SHELL=/bin/sh
PWD=/
VERBOSE=no
TMP_SIZE=32M
info firsttime:mount_rw:time=258690:Mounting root RW for first boot
info firsttime:cursor:Linking Xorg cursor:
ln: /usr/share/fonts/X11/misc/cursor.pcf: No such file or directory
info firsttime:mount_ro:time=258730:Mounting root RO
[ 258.791986] elevator: type not found
[ 258.795660] elevator: switch to
failed
[ 258.805088] elevator: type not found
[ 258.808762] elevator: switch to
failed
[ 258.818109] elevator: type not found
[ 258.821846] elevator: switch to
failed
[ 258.831136] elevator: type not found
[ 258.834991] elevator: switch to
failed
info system:start:time=258839:
/etc/rcS.d/S50diags: line 572: f_proto: not found
info hardware:no_wan::WiFi only device. No WAN found
info system:config:platform=heisenberg,board=eanab,rev=17,proto=N,wifi=Y,wan=N:
[ 258.893023] udevd (194): /proc/194/oom_adj is deprecated, please use /proc/194/oom_score_adj instead.
info system:done:time=259279:
[ 259.309781] fuse init (API version 7.22)
FATAL: Module ppp_async not found.
TI
[ 259.356964] Zforce2 regulator is not enabled! Enabling Zforce2 touch regulator...
[ 259.366186] Zforce2 touch regulator is enabled!
[ 259.433032] input: zforce2 as /devices/platform/zforce2.0/input/input0
/etc/rcS.d/S50diags: line 572: iptables-restore: not found
/etc/rcS.d/S50diags: line 572: /opt/ar6k/host/recEvent: not found
[ 259.672315] kjournald starting. Commit interval 5 seconds
[ 259.677903] EXT3-fs (mmcblk0p3): using internal journal
[ 259.692230] EXT3-fs (mmcblk0p3): recovery complete
[ 259.697033] EXT3-fs (mmcblk0p3): mounted filesystem with ordered data mode
info userstore:run:time=259779,action=start:
info userstore:start:found_bootup_flag:Found BOOTUP flag file
dosfsck 2.11 (12 Mar 2005)
dosfsck 2.11, 12 Mar 2005, FAT32, LFN
Checking we can access the last sector of the filesystem
Clearing dirty flag
Boot sector contents:
System ID "mkdosfs"
Media byte 0xf8 (hard disk)
512 bytes per logical sector
8192 bytes per cluster
2134 reserved sectors
First FAT starts at byte 1092608 (sector 2134)
2 FATs, 32 bit entries
1594880 bytes per FAT (= 3115 sectors)
Root directory start at cluster 2 (arbitrary size)
Data area starts at byte 4282368 (sector 8364)
398580 data clusters (3265167360 bytes)
32 sectors/track, 64 heads
0 hidden sectors
6385648 sectors total
Checking for unused clusters.
Checking free cluster summary.
Performing changes.
/dev/loop/0: 526 files, 101345/398580 clusters
info mntus:fs_error_recover::File system errors recovered
info userstore:found_data::found data.stgz
info bundlefuncs:parse_bundle:BundleType=SP01:
err bundlefuncs:verify_bundle:invalid bundle signature:
info userstore:extract_data::verify_bundle failed RET=127
err userstore:extract_data_failed::extracting data.stgz failed. Ret=127
info filesystems:createWifiSymLink:Cannot find the script to create the Wifi symbolic link:
system: I mntroot:def:Making root filesystem writeable
[ 261.055289] EXT3-fs (mmcblk0p2): using internal journal
ln: /usr/local/sbin/dropbear: File exists
ln: /usr/local/sbin/dropbearkey: File exists
/etc/rcS.d/S50diags: line 13: /usr/local/sbin/dropbearkey: not found
system: I mntroot:def:Making root filesystem read-only
/etc/rcS.d/S50diags: line 13: /usr/local/sbin/dropbear: not found
system: I mntroot:def:Making root filesystem writeable
[ 261.161827] EXT3-fs (mmcblk0p2): using internal journal
system: I mntroot:def:Making root filesystem writeable
mounting waveform filesystem
[ 261.240200] FAT-fs (loop1): Volume was not safely ejected. Run fsck to correct.
rm: can't remove '/lib/firmware/imx/epdc_EANAB.fw': No such file or directory
system: I mntroot:def:Making root filesystem read-only
info display:started:time=261320:
USER=root
prevlevel=N
OLDPWD=/
HOME=/
runlevel=S
TERM=vt102
PATH=/sbin:/bin:/usr/sbin:/usr/bin:/usr/local/bin
SHELL=/bin/sh
PWD=/dev
VERBOSE=no
LD_LIBRARY_PATH=/usr/lib/tts/speech/components/common/:/usr/lib/tts
/etc/rcS.d/S50diags: line 13: kb: not found
system: I mntroot:def:Making root filesystem writeable
[ 261.412134] EXT3-fs (mmcblk0p2): using internal journal
Reduce the voltage
I2C write 0x4B: cmd:0x09 value:0x92
I2C write 0x4B: cmd:0x07 value:0xD0
Do md5sum test
1
2
3
4
5
md5sum test pass, voltage test pass....
restore the voltage setting
I2C write 0x4B: cmd:0x07 value:0xD1
I2C write 0x4B: cmd:0x09 value:0x93
Test done
Config USB adb mode
[ 265.288455] file system registered
[ 265.299142] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 265.306444] android_usb gadget: Number of LUNs=1
[ 265.311074] lun0: LUN: removable file: (no medium)
[ 265.318395] android_usb gadget: android_usb ready
[ 265.528897] android_work: sent uevent USB_STATE=CONNECTED
[ 265.535744] android_work: sent uevent USB_STATE=DISCONNECTED
[ 265.617801] usb_gadget_state_work: gadget state: addresssed
[ 265.638209] android_work: sent uevent USB_STATE=CONNECTED
[ 265.765896] android_work: sent uevent USB_STATE=DISCONNECTED
[ 265.849445] android_work: sent uevent USB_STATE=CONNECTED
[ 265.855692] android_work: sent uevent USB_STATE=DISCONNECTED
[ 265.937757] usb_gadget_state_work: gadget state: addresssed
[ 265.958265] android_work: sent uevent USB_STATE=CONNECTED
[ 266.085746] android_work: sent uevent USB_STATE=DISCONNECTED
[ 266.169383] android_work: sent uevent USB_STATE=CONNECTED
[ 266.175635] android_work: sent uevent USB_STATE=DISCONNECTED
[ 266.257767] usb_gadget_state_work: gadget state: addresssed
[ 266.278157] android_work: sent uevent USB_STATE=CONNECTED
[ 266.401104] usb_gadget_state_work: gadget state: suspended
[ 267.335693] android_usb: already disabled
using port=5555[ 267.345883] read descriptors
[ 267.349807] read strings
[ 272.348863] usb_gadget_state_work: gadget state: suspended
diags : /opt/factory/rootfs_md5_list not found.
ln: /usr/sbin/dtest: File exists
ln: /usr/sbin/inventory: File exists
/etc/init.d/rcS: line 125: boot_milestone: not found
starting pid 622, tty '': '/bin/sh /etc/getty-diags'
starting battery regulation
min: 71
max: 73
Value:0, /sys/class/power_supply/bd7181x_bat/charging
[ 272.459532] android_work: sent uevent USB_STATE=DISCONNECTED
[ 272.548763] android_work: sent uevent USB_STATE=CONNECTED
[ 272.555034] android_work: sent uevent USB_STATE=DISCONNECTED
[ 272.637250] usb_gadget_state_work: gadget state: addresssed
[ 272.657790] android_work: sent uevent USB_STATE=CONNECTED
[ 272.690022] android_usb gadget: high-speed config #1: android
[ 272.696147] usb_gadget_state_work: gadget state: configured
[ 272.702492] android_work: sent uevent USB_STATE=CONFIGURED
Welcome to Kindle!
kindle login: root
root
Password: mario
#################################################
# N O T I C E * N O T I C E * N O T I C E #
#################################################
Rootfs is mounted read-only. Invoke mntroot rw to
switch back to a writable rootfs.
#################################################
[root@kindle root]# reboot
reboot
The system is going down NOW!
Sent SIGTERM to all processes
Terminated
Requesting system rebootesses
[ 290.521904] brcm_wlan_free_mem: static buffers freed
[ 290.527673] imx2-wdt 20bc000.wdog: Device shutdown: Expect reboot!
[ 290.533942] Restarting system.
[ 290.537193] arch_reset_special_mode: cmd: (null)
[ 290.541855] set_boot_mode: mode: d
[ 290.545279] to write to register
[ 290.548512] read out: 13
U-Boot 2014.04 (Jun 04 2016 - 11:52:07)
CPU: Freescale i.MX6SL rev1.3 at 792 MHz
CPU: Temperature 39 C, calibration data: 0x58d50a5f
Reset cause: POR
FRED::: EXTCSD177=0, 179=48FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Board: Heisenberg
Board Id: P00118077373003J
S/N: G000K905738108UK
I2C: ready
DRAM: MR5=0x1,MR6=0x4 512 MiB
WARNING: Caches not enabled
MMC: FRED::: EXTCSD177=0, 179=48FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
REBOOTMODE: 0
using default bootcmdNormal Boot
Hit any key to stop autoboot: 0
mmc1(part 0) is current device
FRED::: EXTCSD177=0, 179=48BOOTing from mmc ...
mmc1(part 0) is current device
MMC read: dev # 1, block # 720, count 28672 ... 28672 blocks read in 319 msec: OK
MMC read: dev # 1, block # 520, count 256 ... 256 blocks read in 7 msec: OK
## Booting kernel from Legacy Image at 80800000 ...
Image Name: Linux-3.10.53-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4786328 Bytes = 4.6 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
## Flattened Device Tree blob at 83000000
Booting using the fdt blob at 0x83000000
Loading Kernel Image ... OK
Loading Device Tree to 9fcae000, end 9fcb85ef ... OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.10.53-lab126 (jenkins-official@sjc10-jbuild09.sjc10.amazon.com) (collect2: error: ld returned 1 exit status) #1 PREEMPT Sat Jun 4 12:16:28 PDT 2016
[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Freescale i.MX6 SoloLite (Device Tree), model: Heisenberg P0
[ 0.000000] printk_reserve_buf:863 log_goal_location:0x8fff0000 log_worst_location:0x8fef0000 new_log_buf_len:32768
[ 0.000000] printk_reserve_buf:883 printk log placed at 8fff0000
[ 0.000000] cma: CMA: reserved 32 MiB at 9c000000
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p1 rootwait rw uart_at_4M
[ 0.000000] Prink buffer will be relocated to physical address: 8fff0000 va: 00000000 new_log_buf_len:32768
[ 0.000000] Prink buffer will be relocated to physical address: 8fff0000 va: 8fff0000 new_log_buf_len:32768
[ 0.000000] log_buf_len: 32768
[ 0.000000] early log buf free: 30752(93%)
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 512MB = 512MB total
[ 0.000000] Memory: 477608k/477608k available, 46680k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xa0800000 - 0xff000000 (1512 MB)
lowmem : 0x80000000 - 0xa0000000 ( 512 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
.text : 0x80008000 - 0x80717760 (7230 kB)
.init : 0x80718000 - 0x808811fc (1445 kB)
.data : 0x80882000 - 0x808c7e80 ( 280 kB)
.bss : 0x808c7e80 - 0x808f0988 ( 163 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x32030000, Cache size: 262144 B
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000469] Calibrating delay loop... 789.70 BogoMIPS (lpj=3948544)
[ 0.040132] pid_max: default: 32768 minimum: 301
[ 0.040272] Mount-cache hash table entries: 512
[ 0.044692] CPU: Testing write buffer coherency: ok
[ 0.044918] Setting up static identity map for 0x80524150 - 0x805241a8
[ 0.045691] devtmpfs: initialized
[ 0.047430] pinctrl core: initialized pinctrl subsystem
[ 0.047680] regulator-dummy: no parameters
[ 0.049794] NET: Registered protocol family 16
[ 0.057062] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.057660] LAB126 Board id - P00118077373003J
[ 0.057741] Use WDOG1 as reset source
[ 0.063154] syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered
[ 0.063407] vdd1p1: 800 <--> 1375 mV at 1100 mV
[ 0.063693] vdd3p0: 2625 <--> 3400 mV at 3000 mV
[ 0.063982] vdd2p5: 2100 <--> 2850 mV at 2500 mV
[ 0.064343] cpu: 725 <--> 1450 mV at 1100 mV
[ 0.064612] vddpu: 725 <--> 1450 mV
[ 0.064974] vddsoc: 725 <--> 1450 mV at 1175 mV
[ 0.066832] syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered
[ 0.068877] syscon 21bc000.ocotp-ctrl: regmap [mem 0x021bc000-0x021bffff] registered
[ 0.070733] amp_boost_enable:iMX:MAX98090:BOARD
[ 0.070766] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.070776] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.074195] imx6sl-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[ 0.079240] bio: create slab <bio-0> at 0
[ 0.080427] SCSI subsystem initialized
[ 0.080649] usbcore: registered new interface driver usbfs
[ 0.080707] usbcore: registered new interface driver hub
[ 0.080835] usbcore: registered new device driver usb
[ 0.082179] bd7181x 0-004b: IRQ 276 GPIO 116
[ 0.087668] buck1: 800 <--> 2000 mV at 1300 mV
[ 0.088852] buck2: 800 <--> 2000 mV at 1300 mV
[ 0.089674] buck3: 1200 <--> 2700 mV at 1800 mV
[ 0.090497] buck4: 1100 <--> 1850 mV at 1200 mV
[ 0.091290] buck5: 1800 <--> 3300 mV at 3200 mV
[ 0.092106] ldo1: 800 <--> 3300 mV at 3200 mV
[ 0.092896] ldo2: 800 <--> 3300 mV at 3200 mV
[ 0.094113] ldo3: 3000 mV
[ 0.094724] ldo4: 800 <--> 3300 mV at 3200 mV
[ 0.095302] ldo5: 800 <--> 3300 mV at 1800 mV
[ 0.095870] dvref: 3000 mV
[ 0.096006] lpsr: 1800 mV
[ 0.096583] wled: at 0 mV 0 <--> 25 mA at 0 mA
[ 0.097469] i2c i2c-0: IMX I2C adapter registered
[ 0.098087] i2c i2c-1: IMX I2C adapter registered
[ 0.098365] i2c i2c-2: IMX I2C adapter registered
[ 0.098477] pps_core: LinuxPPS API ver. 1 registered
[ 0.098487] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.098511] PTP clock support registered
[ 0.098863] MIPI CSI2 driver module loaded
[ 0.098941] Advanced Linux Sound Architecture Driver Initialized.
[ 0.099574] cfg80211: Calling CRDA to update world regulatory domain
[ 0.099610] cfg80211: World regulatory domain updated:
[ 0.099619] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 0.099630] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 0.099640] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 0.099649] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 0.099658] cfg80211: (5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 0.099666] cfg80211: (5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 0.100865] pureg-dummy: no parameters
[ 0.101494] Switching to clocksource mxc_timer1
[ 0.109381] NET: Registered protocol family 2
[ 0.110065] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.110145] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.110196] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.110320] TCP: reno registered
[ 0.110339] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.110359] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.110563] NET: Registered protocol family 1
[ 0.110818] RPC: Registered named UNIX socket transport module.
[ 0.110830] RPC: Registered udp transport module.
[ 0.110838] RPC: Registered tcp transport module.
[ 0.110845] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.117378] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.118006] ldo2p5-dummy: no parameters
[ 0.118757] Bus freq driver module loaded
[ 0.119209] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.124598] VFS: Disk quotas dquot_6.5.2
[ 0.124751] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.127060] NFS: Registering the id_resolver key type
[ 0.127103] Key type id_resolver registered
[ 0.127114] Key type id_legacy registered
[ 0.127154] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.127669] msgmni has been set to 996
[ 0.130598] io scheduler noop registered
[ 0.130613] io scheduler deadline registered
[ 0.130655] io scheduler cfq registered (default)
[ 0.137456] Serial: IMX driver
[ 0.137776] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
[ 0.841402] console [ttymxc0] enabled
[ 0.845552] 2034000.serial: ttymxc2 at MMIO 0x2034000 (irq = 60) is a IMX
[ 0.852755] imx6sl-pinctrl 20e0000.iomuxc: pin MX6SL_PAD_SD1_DAT4 already requested by 20e0000.iomuxc; cannot claim for 2038000.serial
[ 0.864890] imx6sl-pinctrl 20e0000.iomuxc: pin-145 (2038000.serial) status -22
[ 0.872143] imx6sl-pinctrl 20e0000.iomuxc: could not request pin 145 on device 20e0000.iomuxc
[ 0.880680] imx-uart 2038000.serial: Error applying setting, reverse things back
[ 0.888167] 2038000.serial: ttymxc3 at MMIO 0x2038000 (irq = 61) is a IMX
[ 0.895487] serial: Freescale lpuart driver
[ 0.900580] Registering Heisenberg hall sensor platform device
[ 0.907665] imx sema4 driver is registered.
[ 0.916839] brd: module loaded
[ 0.922617] loop: module loaded
bt_pwrctrl_init called..
[ 0.928145]
bt_reset pin obtained is 51
[ 0.932386]
bt_dev_wake pin obtained is 138
[ 0.936756]
bt_host_wake pin obtained is 93
[ 0.941134] IRQ# for BT HOST WAKE: 253
bt_pwrctrl_probe probe successful
[ 0.950086] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.956913] usbcore: registered new interface driver usb-storage
[ 0.963929] imx6sl-pinctrl 20e0000.iomuxc: pin MX6SL_PAD_EPDC_PWRCOM already requested by 20e0000.iomuxc; cannot claim for 2184000.usb
[ 0.976073] imx6sl-pinctrl 20e0000.iomuxc: pin-56 (2184000.usb) status -22
[ 0.982981] imx6sl-pinctrl 20e0000.iomuxc: could not request pin 56 on device 20e0000.iomuxc
[ 0.991432] imx_usb 2184000.usb: Error applying setting, reverse things back
[ 1.002724] usb_gadget_state_work: gadget state: not attached
[ 1.451552] imx_usb 2184000.usb: vbus is error
[ 1.456013] imx_usb 2184000.usb: Error occurs during detection: -22
[ 1.462789] mousedev: PS/2 mouse device common for all mice
[ 1.474304] bd7181x-rtc bd7181x-rtc: rtc core: registered bd7181x-rtc as rtc0
[ 1.482029] snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc1
[ 1.490420] i2c /dev entries driver
[ 1.494514] bd7181x-power bd7181x-power: battery_cycle = 0
[ 1.500633] Status Register 1 == 0x0
[ 1.504673] Status Register 2 == 0x0
[ 1.508673] Status Register 3 == 0x40
[ 1.512776] Status Register 4 == 0x0
[ 1.516774] Status Register 5 == 0x80
[ 1.520855] Status Register 6 == 0x0
[ 1.524869] Status Register 7 == 0x0
[ 1.528866] Status Register 8 == 0x2
[ 1.532877] Status Register 9 == 0x0
[ 1.536876] Status Register 10 == 0x0
[ 1.540959] Status Register 11 == 0x0
[ 1.545057] Status Register 12 == 0x0
[ 1.551611] errflags = 1
[ 1.554153] bit0 is set
[RESET REASONS]: SOFTWARE_RESTART: Software Initiated System Restart
[ 1.579037] imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0) imx2_wdt.base=0xa0920000 base pa:0x20bc000 imx2_wdt.clk=0x9a00c100
[ 1.593803] cpuidle: using governor ladder
[ 1.597931] cpuidle: using governor menu
[ 1.602029] sdhci: Secure Digital Host Controller Interface driver
[ 1.608234] sdhci: Copyright(c) Pierre Ossman
[ 1.612631] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.623097] mmc1: no vqmmc regulator found
[ 1.627357] mmc1: Not allowing HS200
[ 1.630971] mmc1: no vmmc regulator found
[ 1.681549] mmc1: SDHCI controller on 2190000.usdhc [2190000.usdhc] using DMA
[ 1.692190] mmc0: no vqmmc regulator found
[ 1.696302] mmc0: Not allowing HS200
[ 1.699889] mmc0: no vmmc regulator found
[ 1.741545] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using DMA
[ 1.750826] usbcore: registered new interface driver usbhid
[ 1.756455] usbhid: USB HID core driver
[ 1.761327] NET: Registered protocol family 26
[ 1.768044] TCP: cubic registered
[ 1.771374] IPv6: Loaded, but administratively disabled, reboot required to enable
[ 1.778999] sit: IPv6 over IPv4 tunneling driver
[ 1.784131] NET: Registered protocol family 17
[ 1.790696] 8021q: 802.1Q VLAN Support v1.8
[ 1.799020] Key type dns_resolver registered
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 1.835858] ldo5: disabling
[ 1.844634] ldo4: disabling
[ 1.847847] regulator-dummy: disabling
[ 1.851860] imx mcc test is registered.
[ 1.856522] bd7181x-rtc bd7181x-rtc: setting system clock to 2001-01-06 22:56:39 UTC (978821799)
[ 1.868902] ALSA device list:
[ 1.873976] No soundcards found.
[ 1.878598] Freeing unused kernel memory: 1444K (80718000 - 80881000)
3.10.53-lab126 #1 PREEMPT Sat Jun 4 12:16:28 PDT 2016 armv7l
[ 2.095838] mmc0: BKOPS_EN bit is not set
[ 2.118067] mmc0: new high speed DDR MMC card at address 0001
[ 2.124146] mmcblk0: mmc0:0001 NJ2ZMB 3.64 GiB
[ 2.128775] mmcblk0boot0: mmc0:0001 NJ2ZMB partition 1 4.00 MiB
[ 2.134818] mmcblk0boot1: mmc0:0001 NJ2ZMB partition 2 4.00 MiB
[ 2.140822] mmcblk0rpmb: mmc0:0001 NJ2ZMB partition 3 512 KiB
[ 2.147499] mmcblk0: p1 p2 p3 p4
[ 2.153624] mmcblk0boot1: unknown partition table
[ 2.160443] mmcblk0boot0: unknown partition table
[ 2.198419] INFO:child exited with status 00000000
[ 2.203876] INFO:find_file:118 Found V220_C283_BDB501_ED060SCSU1_TC.wrf.gz
ERROR:wfm_count=1
[ 2.212861] mxc_epdc_eink: module license 'proprietary' taints kernel.
[ 2.219567] Disabling lock debugging due to kernel taint
[ 2.225282] INFO:Loaded module /lib/modules/mxc_epdc_eink.ko (11172 bytes)
Panel VCOM string: 2690
[ 2.236440] imx_epdc_fb 20f4000.epdc: vcom_steps 125
[ 2.241652] imx_epdc_fb 20f4000.epdc: Memory override detected TotalMem:512M X:800 Y:600 FBMem:6M
[ 2.257580] imx_epdc_fb 20f4000.epdc: EPDC version = 2.1.0
[ 2.324285] wv_file->wdh.luts & 0xC =4
[ 4.164649] INFO:Loaded module /lib/modules/mxc_epdc_fb.ko (79696 bytes)
[ 4.448811] INFO:eink initialized... (486400 bytes)
Press [ENTER] for recovery menu... 0 /[ 5.472702] INFO:!!! Checking MBR /dev/mmcblk0 !!!!
[ 5.486678] INFO:partition 2, start sector is 987136
[ 5.491955] INFO:partition 3, start sector is 1118208
[ 5.497183] INFO:partition 4, start sector is 1249280
[ 5.502424] INFO:maximizing partition 6385664 sectors
[ 5.507541] INFO:*** Partition table verified for /dev/mmcblk0 ***
/dev/mmcblk0p4:[ 5.518422] INFO:Setup loop device /dev/loop0 for /dev/mmcblk0p4 + 8192
CHS=4/16/99776 size=3269459968 [ 5.528015] FAT-fs (loop0): Volume was not safely ejected. Run fsck to correct.
bytes
flag type first [ 5.536249] INFO:Checking for updates... (auto-pilot mode)
last lba first lba size
Part[ 5.544474] INFO:No update*.bin found; no update needed.
ition p1:
0x00 0x0b 16 <[ 5.552925] INFO:no updates found.
large> 16 6385648
CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
BOOTING DEFAULT.
IP-Config: no devices to configure
[ 6.383781] kjournald starting. Commit interval 5 seconds
[ 6.389450] EXT3-fs (mmcblk0p1): using internal journal
[ 6.394811] EXT3-fs (mmcblk0p1): mounted filesystem with ordered data mode
kinit: Mounted root (ext3 filesystem).
info sytem:mounted_proc::
info system:mounted_sys::
info system:sy00::
info firsttime:mount_rw:time=6880:Mounting root RW for first boot
info firsttime:lostfound:Removing lost+found:
info firsttime:usrlocal:Changing ownership for usr local:
info firsttime:mtab:Linking /var/tmp:
info firsttime:mtab:Linking Kindle Registry:
info firsttime:xorgconf:Linking xorg.conf:
info firsttime:cursor:Linking Xorg cursor:
info firsttime:ssh:Generating rsa keys:
info firsttime:mount_ro:time=8260:Mounting root RO
info system:mounted_dev::
info milestone:8.32:49.1:
info milestone:8.36:49.2:
info milestone:8.38:49.3:
info milestone:8.42:49.4:
info milestone:8.45:49.5:
info sytem:mounted_tmpfs::
info milestone:8.60:sy50:
info system:start:time=8620:
info hardware:no_wan::WiFi only device. No WAN found
info system:config:platform=heisenberg,board=eanab,rev=17,proto=Y,wifi=Y,wan=N:
[ 8.759781] udevd (298): /proc/298/oom_adj is deprecated, please use /proc/298/oom_score_adj instead.
info milestone:8.78:sy51:
lipc-send-event[407]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[407]: C def:dbusi::Failed to init dbus
lipc-send-event[407]: E def:open::Failed to open LIPC
lipc-send-event[407]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
lipc-send-event[412]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[412]: C def:dbusi::Failed to init dbus
lipc-send-event[412]: E def:open::Failed to open LIPC
lipc-send-event[412]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
info milestone:9.91:sy99:
info system:done:time=9950:
crond[427]: crond: crond (busybox 1.17.1) started, log level 8
init.exe: recevent pre-start process (430) terminated with st▒info system_cramfs_loopbacks:mountingcramfs:Mounting compressed directories filesystem images:
warn system_cramfs_loopbacks:mountpointmissing:Image /lib/firmware/cyttsp.cramfs.img not mounted, non existing mounting point:
info system_cramfs_loopbacks:mounted:Image /usr/share/X11/xkb.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/java/lib/fonts.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /etc/kdb.src.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/lib/locale.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/share/keyboard.cramfs.img mounted:
info system:emiting_event:mounted_cramfs_loopbacks:
debug sytem:event_emitted:mounted_cramfs_loopbacks:
info milestone:10.72:fs75:
info system:emiting_event:loaded_modules_dependencies:
debug sytem:event_emitted:loaded_modules_dependencies:
info modules:modprobe:loading module fsl_otg_arc:
crit modules:modprobe_failed:failed to load module fsl_otg_arc:
info modules:modprobe:loading module ehci_hcd:
crit modules:modprobe_failed:failed to load module ehci_hcd:
info modules:modprobe:loading module fuse:
[ 10.824945] fuse init (API version 7.22)
info system:emiting_event:loaded_fuse:
debug sytem:event_emitted:loaded_fuse:
info hardware:no_wan::WiFi only device. No WAN found
info milestone:10.86:fs00:
info system:emiting_event:loaded_ppp_async:
debug sytem:event_emitted:loaded_ppp_async:
info system:emiting_event:loaded_fakekey:
debug sytem:event_emitted:loaded_fakekey:
[ 10.958831] kjournald starting. Commit interval 5 seconds
[ 10.964943] EXT3-fs (mmcblk0p3): using internal journal
[ 10.970764] EXT3-fs (mmcblk0p3): recovery complete
[ 10.976339] EXT3-fs (mmcblk0p3): mounted filesystem with ordered data mode
[ 10.991644] EXT3-fs (mmcblk0p1): using internal journal
info filesystems_var_local:guid:Fetching existing guid:
info milestone:11.06:fs23:
info system:emiting_event:mounted_varLocal:
debug sytem:event_emitted:mounted_varLocal:
info milestone:11.12:fs25:
info milestone:11.15:vi00:
Welcome to Kindle!
kindle login: [ 11.282955] Zforce2 regulator is not enabled! Enabling Zforce2 touch regulator...
[ 11.329858] Zforce2 touch regulator is enabled!
[ 11.395478] EXT3-fs (mmcblk0p1): using internal journal
[ 11.537512] FAT-fs (loop1): Volume was not safely ejected. Run fsck to correct.
[ 11.645942] input: zforce2 as /devices/platform/zforce2.0/input/input0
info milestone:11.84:vi99:
info display:started:time=11890:
info system:emiting_event:display_ready:
debug sytem:event_emitted:display_ready:
info system:emiting_event:loaded_touch:
debug sytem:event_emitted:loaded_touch:
info userstore:run:time=12270,action=start:
info userstore:start:found_bootup_flag:Found BOOTUP flag file
info prereg:PRAGMA_QUICK_CHECK_PASSED::sts=0
info mntus:fs_error_recover::File system errors recovered
[ 14.222494] g_mass_storage gadget: Mass Storage Function, version: 2009/09/11
[ 14.229644] g_mass_storage gadget: Number of LUNs=1
[ 14.247921] lun0: LUN: removable file: (no medium)
[ 14.254909] fsg_bind:3212
[ 14.257557] g_mass_storage gadget: Internal Storage, version: 2009/09/11
[ 14.276514] g_mass_storage gadget: userspace failed to provide iSerialNumber
[ 14.289602] g_mass_storage gadget: g_mass_storage ready
info system:emiting_event:mounted_userstore:
debug sytem:event_emitted:mounted_userstore:
info milestone:14.40:fs50:
info milestone:14.46:fs90:
info milestone:14.53:fs99:
info battery:charged:cap=,mV=,mAH=:
[ 14.598626] usb_gadget_state_work: gadget state: addresssed
info system:emiting_event:battery_ready:
[ 14.643647] g_mass_storage gadget: high-speed config #1: Linux File-Backed Storage
[ 14.651262] usb_gadget_state_work: gadget state: configured
[ 14.657414]
send_online_uevent:432 fsg_ 0x0 recovery_mode:0
debug sytem:event_emitted:battery_ready:
info milestone:14.69:sys99:
info system:emiting_event:devcap_ready:
debug sytem:event_emitted:devcap_ready:
info system:emiting_event:dbus_ready:
debug sytem:event_emitted:dbus_ready:
info dbus:check-update:status=2:dbus_ready sent
info hardware:no_wan::WiFi only device. No WAN found
info milestone:16.08:xx00:
info X:load:time=16200:
info X:xorg.conf:Generating xorg.conf:
info X:xorg.conf:xorg.conf generated:
info milestone:17.77:xx50:
info X:starting:time=17830:
info milestone:21.60:xx99:
info X:started:time=21640:
info system:emiting_event:x_setup_ready:
debug sytem:event_emitted:x_setup_ready:
info asr_setup:winmgr_running=true. winmgr is ready::
info locale:read:lang=de_DE.utf8,lc_all=de_DE.utf8:Retrieved Language
info system:emiting_event:langpicker_ready:
debug sytem:event_emitted:langpicker_ready:
info blanket_f:module already loaded:splash:
info milestone:23.73:pi00:
info milestone:24.02:pi99:
info system:emiting_event:contentpack_font_ready:
debug sytem:event_emitted:contentpack_font_ready:
info milestone:25.61:fr00:
info milestone:25.73:fr50:
info milestone:25.74:fr51:
info framework:starting:time=26900:
info hardware:no_wan::WiFi only device. No WAN found
[ 30.359974] dhd_module_init in
[ 30.363673] dhd_module_init fw_image_unaligned=9a500000 fw_image=9a500000
[ 30.374682] brcm_wlan_power: setting gpio #[47] on
[ 30.541632] found wifi platform device bcmdhd_wlan
[ 30.553191] dhd_module_init out
[ 30.881706] mmc1: new high speed SDIO card at address 0001
[ 30.906311] alloc static buf at 9a440000!
[ 30.925345] DHD: dongle ram size is set to 524288(orig 524288) at 0x0
[ 30.934026] wifi_platform_get_mac_addr
CFG80211-ERROR) wl_event_handler : [ 30.949888] dhd_deferred_work_init: work queue initialized
tsk Enter, tsk = 0x9a23f5dc
[ 30.966130] dhdsdio_download_code_file: download firmware '/opt/brcm_4343w/wifi/firmware/fw_bcmdhd_sr.bin' and save a copy to 9a500000
[ 31.052963] dhdsdio_download_code_file finished f/w download fw_image_size=351012
[ 31.068294] dhdsdio_download_nvram: MAX=4096 len=906 read
[ 31.076305] dhdsdio_download_nvram: MAX=4096 len=906 saved
[ 31.146009] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
[ 31.161595] wifi_platform_get_mac_addr
[ 31.172778] dhd_wlfc_init(): successfully enabled bdcv2 tlv signaling, 79
[ 31.180464] dhd_wlfc_init: query wlfc_mode succeed, fw_caps=0x1c
[ 31.189827] dhd_wlfc_init(): wlfc_mode=0x1c, ret=0
[ 31.196191]
Dongle Host Driver, version 1.201.59 (r506368)
Compiled from
[ 31.210833] Register interface [wlan0] MAC: 00:be:6e
info milestone:61.53:fr99:
info framework:started:time=61560,delta=35830:
info blanket_f:loading blanket module:usb:
info blanket_f:unloading blanket module:splash:
info system:emiting_event:framework_ready:
debug sytem:event_emitted:framework_ready:
info stored:started::
info stored:read_in_counters:REBOOTS=0, REBOOT_LIMIT=1, RESTARTS=0, RESTART_LIMIT=5:
[ 63.161576] EXT3-fs (mmcblk0p1): using internal journal
info monitor:writing_file:file=/var/run/upstart/stored.restarts:
Retrieved 344 keys for system/daemon/pmond/
[ 71.039917] fsg_suspend:3275
[ 71.042887] usb_gadget_state_work: gadget state: suspended
[ 71.348453] fsg_disable:2563
[ 71.351413]
send_offline_uevent:407 fsg_ 0xa unsafe 1 recovery_mode:0
[ 71.380822]
send_offline_uevent:407 fsg_ 0x0 unsafe 0 recovery_mode:0
info asr_setup:winmgr_running=true. winmgr is ready::
[ 73.874506] usb_gadget_state_work: gadget state: not attached
[ 814.901735] usb_gadget_state_work: gadget state: powered
[ 815.197328] usb_gadget_state_work: gadget state: addresssed
[ 815.242808] g_mass_storage gadget: high-speed config #1: Linux File-Backed Storage
[ 815.250488]
send_online_uevent:432 fsg_ 0x0 recovery_mode:0
[ 815.258059] usb_gadget_state_work: gadget state: configured
info stored:post-stop script - Time Interval = 752::
info stored:post-stop script - cleared counters::
info stored:post-stop script - sending event to appmgrd::
info stored:started::
info stored:read_in_counters:REBOOTS=0, REBOOT_LIMIT=1, RESTARTS=0, RESTART_LIMIT=5:
info monitor:writing_file:file=/var/run/upstart/stored.restarts:
[ 835.345080] fsg_disable:2563
[ 835.348014] g_mass_storage gadget: high-speed config #0: unconfigured
[ 835.354594]
send_offline_uevent:407 fsg_ 0x2 unsafe 0 recovery_mode:0
[ 835.379353] usb_gadget_state_work: gadget state: suspended
info asr_setup:winmgr_running=true. winmgr is ready::
[ 935.144690] usb_gadget_state_work: gadget state: not attached
03-19-2021, 09:40 AM
Similar Threads