HanLin V3 locks up

roytravis · 02-04-2009, 07:50 PM

I have been using the HanLin for about a month now and I am really enjoying it.
However, on two occasion now I have had the device lock up. The first time I fixed it by removing the battery. The book booted after the battery was reinstalled.
The second time this did not provide a solution and I recharged the battery overnight despite the indicator showing half charge. I was able to reboot normally in the morning.
It might be worth mentioning that I leave the HanLin on at the last page I am reading, at all times. I do this in the belief that there is no power usage during this time. I intend now to put in into locked keyboard mode to see if that fixes the problem

Any thoughts welcome.

JoeD · 02-05-2009, 07:51 AM

I use the "locked" option, but I don't think it makes a difference whether you lock it or leave it on the last page in terms of power usage.

Rather than remove the battery, if it locks up again, there's a small hole on the back of the device you can stick a small paper clip into to reset the device.

Have a look on the about screen to see which version of the firmware you have installed. It might be worth updating to one of the more recent ones. I remember getting the occasional lock/reboot on one of the older firmware, but the more recent ones have been a lot more stable.

I'm currently testing out the open inkpot firmware, which considering it's a development snapshot and not a real release, has been very stable so far. Installed it on the 29th/30th Jan and so far had no issues.

slayda · 02-05-2009, 11:09 AM

I think I've found my ideal reader - the Hanlin V3 (actually mine is the EZ Reader) with OpenInkPot fimrware. All of my books are DRM free.

phenomshel · 02-05-2009, 01:10 PM

I'm loving my EZ Reader - and I've had no problems, but I've only had it a day, too, *laugh*.

roytravis · 02-05-2009, 05:27 PM

Thank you all for your input. I do have the latest version of the firmware.
I had three lock ups in a short period, on the first two occasions the reset did not fix the problem, it did however on the last.
I have now reloaded the latest firmware file and so far it seems to be stable.
Incidentally the lock ups all occurred within one book which I have now finished so it may have been the source of the problem

IgnareAcademy · 05-27-2009, 04:35 AM

According to some, the lockups may be due to Hanlin shipping their product with a crappy Chinese battery instead of the original Nokia battery. Apparently some users end up with a good battery, while others get a battery which cannot deliver electricity reliably all the time.
Some say they got rid of the lockups by replacing the Hanlin battery with an original Nokia battery.
I have to try because I experience crashes (my Hanlin clone exits from the book I read) when the battery is not fully charged.

leandroide · 05-27-2009, 06:23 AM

Hi all

Since I installed last lbook's firmware, I found the reader is much more stable than before.

With other firmwares (grammata, bebook, hanlin...) the reader locked up often with two bars of battery remaining. With lbook firmware installed, I saw the low battery warning for the first time in my reader!

L.

IgnareAcademy · 05-27-2009, 07:08 AM

My reader is less unstable with the latest (and great) LBook firmware too, especially when the battery is fully charged.
But it is not perfectly stable.

keng2000 · 05-27-2009, 11:03 AM

I haven't founded the problem right now,
My firmware is mixed from LBOOK and HANLIN. FW.
Beta bookshelf and viewer from JINKEand Coolreader from LBOOK (mix newest libraries)

02-04-2009, 07:50 PM	#1
roytravis Enthusiast Posts: 42 Karma: 54 Join Date: Jan 2009 Location: Melbourne, Australia Device: hanlin	HanLin V3 locks up I have been using the HanLin for about a month now and I am really enjoying it. However, on two occasion now I have had the device lock up. The first time I fixed it by removing the battery. The book booted after the battery was reinstalled. The second time this did not provide a solution and I recharged the battery overnight despite the indicator showing half charge. I was able to reboot normally in the morning. It might be worth mentioning that I leave the HanLin on at the last page I am reading, at all times. I do this in the belief that there is no power usage during this time. I intend now to put in into locked keyboard mode to see if that fixes the problem Any thoughts welcome.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Settings option locks up device when SD card is in.	nimblem	Astak EZReader	12	05-28-2010 02:30 PM
Classic Wifilocker also locks 3G signal..great!	bthoven	Barnes & Noble NOOK	0	02-28-2010 01:47 PM
Library Software Locks Up	sakura-panda	Sony Reader	8	01-02-2010 02:40 AM
Document locks up Kindle 2	Rhett	Amazon Kindle	0	10-25-2009 08:45 PM
Info on DRM and Digital Locks...	Red Alert	Lounge	1	12-11-2007 12:31 PM

02-05-2009, 07:51 AM	#2
JoeD Guru Posts: 895 Karma: 4383958 Join Date: Nov 2007 Device: na	I use the "locked" option, but I don't think it makes a difference whether you lock it or leave it on the last page in terms of power usage. Rather than remove the battery, if it locks up again, there's a small hole on the back of the device you can stick a small paper clip into to reset the device. Have a look on the about screen to see which version of the firmware you have installed. It might be worth updating to one of the more recent ones. I remember getting the occasional lock/reboot on one of the older firmware, but the more recent ones have been a lot more stable. I'm currently testing out the open inkpot firmware, which considering it's a development snapshot and not a real release, has been very stable so far. Installed it on the 29th/30th Jan and so far had no issues.

02-05-2009, 11:09 AM	#3
slayda Retired & reading more! Posts: 2,764 Karma: 1884247 Join Date: Sep 2006 Location: North Alabama, USA Device: Kindle 1, iPad Air 2, iPhone 6S+, Kobo Aura One	I think I've found my ideal reader - the Hanlin V3 (actually mine is the EZ Reader) with OpenInkPot fimrware. All of my books are DRM free.

02-05-2009, 01:10 PM	#4
phenomshel ZCD BombShel Posts: 4,793 Karma: 8293322 Join Date: Jan 2009 Location: The Frozen North (aka Illinois, USA) Device: iPad, STB Kindle Oasis	I'm loving my EZ Reader - and I've had no problems, but I've only had it a day, too, laugh.

02-05-2009, 05:27 PM	#5
roytravis Enthusiast Posts: 42 Karma: 54 Join Date: Jan 2009 Location: Melbourne, Australia Device: hanlin	Thank you all for your input. I do have the latest version of the firmware. I had three lock ups in a short period, on the first two occasions the reset did not fix the problem, it did however on the last. I have now reloaded the latest firmware file and so far it seems to be stable. Incidentally the lock ups all occurred within one book which I have now finished so it may have been the source of the problem

05-27-2009, 04:35 AM	#6
IgnareAcademy Banned Posts: 49 Karma: 50 Join Date: May 2009 Device: Hanlin clone	According to some, the lockups may be due to Hanlin shipping their product with a crappy Chinese battery instead of the original Nokia battery. Apparently some users end up with a good battery, while others get a battery which cannot deliver electricity reliably all the time. Some say they got rid of the lockups by replacing the Hanlin battery with an original Nokia battery. I have to try because I experience crashes (my Hanlin clone exits from the book I read) when the battery is not fully charged.

05-27-2009, 06:23 AM	#7
leandroide Zealot Posts: 144 Karma: 92 Join Date: May 2006 Location: Vigo, Spain Device: Papyre 6.1 (Hanlin V3)	Hi all Since I installed last lbook's firmware, I found the reader is much more stable than before. With other firmwares (grammata, bebook, hanlin...) the reader locked up often with two bars of battery remaining. With lbook firmware installed, I saw the low battery warning for the first time in my reader! L.

05-27-2009, 07:08 AM	#8
IgnareAcademy Banned Posts: 49 Karma: 50 Join Date: May 2009 Device: Hanlin clone	My reader is less unstable with the latest (and great) LBook firmware too, especially when the battery is fully charged. But it is not perfectly stable.

05-27-2009, 11:03 AM	#9
keng2000 Researcher and Consultant Posts: 210 Karma: 364 Join Date: Nov 2008 Location: Bangkok, THAILAND Device: MACBOOKPRO17" HP2400TX SONYUX27	I haven't founded the problem right now, My firmware is mixed from LBOOK and HANLIN. FW. Beta bookshelf and viewer from JINKEand Coolreader from LBOOK (mix newest libraries)

Advert

Advert