07-02-2018, 03:40 PM | #391 | |
Member
Posts: 10
Karma: 46734
Join Date: Jun 2018
Location: Austria
Device: Kindle 8 (G000 K905) KT3
|
Quote:
I‘ll try to find something that helps me in this forums! |
|
07-09-2018, 02:54 AM | #392 |
Member
Posts: 10
Karma: 46734
Join Date: Jun 2018
Location: Austria
Device: Kindle 8 (G000 K905) KT3
|
Hey guys! I successfully managed to jailbreak my kindle
Here's how it worked: 1)At first I had to download the correct Firmware for my device (In my case it was "factory_KT3_5.8.0_initial.bin" ) 2)Then I renamed it to update.bin (necessary in a later step) and put it to the root directory of my kindle 3) I connected the Serial-USB-Converter to my kindle 4) I startet the device and interrupted the booting sequence by pressing the "enter" button to get into uboot 5)Here I entered the command "run diags_boot" to get into diagnostics mode 6)After the diagnostics mode was fully loaded I pressed enter to get into kindle Login 7)I logged in with "root" and password "mario" 8)When I got logged in I entered "reboot" 9)Now in the boot sequence there was an entry to get into recovery mode. It was shown up just for about 1 second. When this entry was shown I had to press "enter" to get into this mode. 10) Now I got into recovery mode. 11) Here I had 10 seconds time to choose one of the operations. 12) I entered "u" for "Update using update*.bin file on FAT Partition" 13) When the update was finished I was on Firmware 5.8.0 So I just had to follow the Software jailbreak tutorial! Here's the log from PuTTY: Code:
U-Boot 2014.04 (Jan 24 2018 - 12:41:30) CPU: Freescale i.MX6SL rev1.3 at 792 MHz CPU: Temperature 39 C, calibration data: 0x58d50a5f Reset cause: POR FRED::: EXTCSD177=0, 179=48FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Board: Heisenberg Board Id: P00118077373003J S/N: G000K905738108UK I2C: ready DRAM: MR5=0x1,MR6=0x4 512 MiB WARNING: Caches not enabled MMC: FRED::: EXTCSD177=0, 179=48FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial REBOOTMODE: 0 using default bootcmdNormal Boot Hit any key to stop autoboot: 0 uboot > uboot > uboot > run diags_boot run diags_boot BOOTing diags from mmc ... mmc1(part 0) is current device MMC read: dev # 1, block # 29392, count 28672 ... 28672 blocks read in 319 msec: OK MMC read: dev # 1, block # 29192, count 256 ... 256 blocks read in 6 msec: OK ## Booting kernel from Legacy Image at 80800000 ... Image Name: Linux-3.10.53-lab126 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4788336 Bytes = 4.6 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Kernel Image ... OK Loading Device Tree to 9fcae000, end 9fcb85ef ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.10.53-lab126 (jenkins-official@sjc10-jbuild07) (collect2: error: ld returned 1 exit status) #1 PREEMPT Fri Jul 22 00:45:40 PDT 2016 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Freescale i.MX6 SoloLite (Device Tree), model: Heisenberg P0 [ 0.000000] printk_reserve_buf:863 log_goal_location:0x8fff0000 log_worst_location:0x8fef0000 new_log_buf_len:32768 [ 0.000000] printk_reserve_buf:883 printk log placed at 8fff0000 [ 0.000000] cma: CMA: reserved 32 MiB at 9c000000 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p2 rootwait rw [ 0.000000] Prink buffer will be relocated to physical address: 8fff0000 va: 00000000 new_log_buf_len:32768 [ 0.000000] Prink buffer will be relocated to physical address: 8fff0000 va: 8fff0000 new_log_buf_len:32768 [ 0.000000] log_buf_len: 32768 [ 0.000000] early log buf free: 30776(93%) [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 512MB = 512MB total [ 0.000000] Memory: 477600k/477600k available, 46688k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xa0800000 - 0xff000000 (1512 MB) lowmem : 0x80000000 - 0xa0000000 ( 512 MB) pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) modules : 0x7f000000 - 0x7fe00000 ( 14 MB) .text : 0x80008000 - 0x807187c4 (7234 kB) .init : 0x80719000 - 0x80882b7c (1447 kB) .data : 0x80884000 - 0x808c9e80 ( 280 kB) .bss : 0x808c9e80 - 0x808f29c8 ( 163 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L310 cache controller enabled [ 0.000000] l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x32030000, Cache size: 262144 B [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000465] Calibrating delay loop... 789.70 BogoMIPS (lpj=3948544) [ 0.040130] pid_max: default: 32768 minimum: 301 [ 0.040271] Mount-cache hash table entries: 512 [ 0.044669] CPU: Testing write buffer coherency: ok [ 0.044893] Setting up static identity map for 0x80524338 - 0x80524390 [ 0.045673] devtmpfs: initialized [ 0.047389] pinctrl core: initialized pinctrl subsystem [ 0.047639] regulator-dummy: no parameters [ 0.049758] NET: Registered protocol family 16 [ 0.057114] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.057697] LAB126 Board id - P00118077373003J [ 0.057777] Use WDOG1 as reset source [ 0.063223] syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered [ 0.063475] vdd1p1: 800 <--> 1375 mV at 1100 mV [ 0.063761] vdd3p0: 2625 <--> 3400 mV at 3000 mV [ 0.064056] vdd2p5: 2100 <--> 2850 mV at 2500 mV [ 0.064414] cpu: 725 <--> 1450 mV at 1100 mV [ 0.064688] vddpu: 725 <--> 1450 mV [ 0.065047] vddsoc: 725 <--> 1450 mV at 1175 mV [ 0.066912] syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered [ 0.068957] syscon 21bc000.ocotp-ctrl: regmap [mem 0x021bc000-0x021bffff] registered [ 0.070830] amp_boost_enable:iMX:MAX98090:BOARD [ 0.070861 ] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.070871] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.074153] imx6sl-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.079182] bio: create slab <bio-0> at 0 [ 0.080362] SCSI subsystem initialized [ 0.080584] usbcore: registered new interface driver usbfs [ 0.080650] usbcore: registered new interface driver hub [ 0.080766] usbcore: registered new device driver usb [ 0.082107] bd7181x 0-004b: IRQ 276 GPIO 116 [ 0.087661] buck1: 800 <--> 2000 mV at 1300 mV [ 0.088852] buck2: 800 <--> 2000 mV at 1300 mV [ 0.089686] buck3: 1200 <--> 2700 mV at 1800 mV [ 0.090498] buck4: 1100 <--> 1850 mV at 1200 mV [ 0.091298] buck5: 1800 <--> 3300 mV at 3200 mV [ 0.092123] ldo1: 800 <--> 3300 mV at 3200 mV [ 0.092917] ldo2: 800 <--> 3300 mV at 3200 mV [ 0.094149] ldo3: 3000 mV [ 0.094767] ldo4: 800 <--> 3300 mV at 3200 mV [ 0.095351] ldo5: 800 <--> 3300 mV at 1800 mV [ 0.095923] dvref: 3000 mV [ 0.096061] lpsr: 1800 mV [ 0.096648] wled: at 0 mV 0 <--> 25 mA at 0 mA [ 0.097529] i2c i2c-0: IMX I2C adapter registered [ 0.098144] i2c i2c-1: IMX I2C adapter registered [ 0.098418] i2c i2c-2: IMX I2C adapter registered [ 0.098529] pps_core: LinuxPPS API ver. 1 registered [ 0.098540] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.098565] PTP clock support registered [ 0.098911] MIPI CSI2 driver module loaded [ 0.098996] Advanced Linux Sound Architecture Driver Initialized. [ 0.099619] cfg80211: Calling CRDA to update world regulatory domain [ 0.099653] cfg80211: World regulatory domain updated: [ 0.099663] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 0.099674] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 0.099684] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 0.099693] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 0.099702] cfg80211: (5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A, 3000 mBm) [ 0.099711] cfg80211: (5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm) [ 0.100890] pureg-dummy: no parameters [ 0.101518] Switching to clocksource mxc_timer1 [ 0.109429] NET: Registered protocol family 2 [ 0.110106] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.110191] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.110316] TCP: Hash tables configured (established 4096 bind 4096) [ 0.110372] TCP: reno registered [ 0.110388] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.110407] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.110613] NET: Registered protocol family 1 [ 0.110874] RPC: Registered named UNIX socket transport module. [ 0.110886] RPC: Registered udp transport module. [ 0.110895] RPC: Registered tcp transport module. [ 0.110903] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.117398] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available [ 0.118023] ldo2p5-dummy: no parameters [ 0.118756] Bus freq driver module loaded [ 0.119199] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.124565] VFS: Disk quotas dquot_6.5.2 [ 0.124710] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.127007] NFS: Registering the id_resolver key type [ 0.127047] Key type id_resolver registered [ 0.127057] Key type id_legacy registered [ 0.127098] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.127609] msgmni has been set to 996 [ 0.130577] io scheduler noop registered [ 0.130591] io scheduler deadline registered [ 0.130634] io scheduler cfq registered (default) [ 0.137456] Serial: IMX driver [ 0.137778] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX [ 0.840918] console [ttymxc0] enabled [ 0.845077] 2034000.serial: ttymxc2 at MMIO 0x2034000 (irq = 60) is a IMX [ 0.852302] imx6sl-pinctrl 20e0000.iomuxc: pin MX6SL_PAD_SD1_DAT4 already requested by 20e0000.iomuxc; cannot claim for 2038000.serial [ 0.864454] imx6sl-pinctrl 20e0000.iomuxc: pin-145 (2038000.serial) status -22 [ 0.871724] imx6sl-pinctrl 20e0000.iomuxc: could not request pin 145 on device 20e0000.iomuxc [ 0.880277] imx-uart 2038000.serial: Error applying setting, reverse things back [ 0.887778] 2038000.serial: ttymxc3 at MMIO 0x2038000 (irq = 61) is a IMX [ 0.895120] serial: Freescale lpuart driver [ 0.900211] Registering Heisenberg hall sensor platform device [ 0.907305] imx sema4 driver is registered. [ 0.916484] brd: module loaded [ 0.922285] loop: module loaded bt_pwrctrl_init called.. [ 0.927847] bt_reset pin obtained is 51 [ 0.932134] bt_dev_wake pin obtained is 138 [ 0.936520] bt_host_wake pin obtained is 93 [ 0.940912] IRQ# for BT HOST WAKE: 253 bt_pwrctrl_probe probe successful [ 0.949852] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.956731] usbcore: registered new interface driver usb-storage [ 0.963767] imx6sl-pinctrl 20e0000.iomuxc: pin MX6SL_PAD_EPDC_PWRCOM already requested by 20e0000.iomuxc; cannot claim for 2184000.usb [ 0.975926] imx6sl-pinctrl 20e0000.iomuxc: pin-56 (2184000.usb) status -22 [ 0.982849] imx6sl-pinctrl 20e0000.iomuxc: could not request pin 56 on device 20e0000.iomuxc [ 0.991316] imx_usb 2184000.usb: Error applying setting, reverse things back [ 1.002623] usb_gadget_state_work: gadget state: not attached [ 1.451574] imx_usb 2184000.usb: vbus is error [ 1.456035] imx_usb 2184000.usb: Error occurs during detection: -22 [ 1.462814] mousedev: PS/2 mouse device common for all mice [ 1.474390] bd7181x-rtc bd7181x-rtc: rtc core: registered bd7181x-rtc as rtc0 [ 1.482095] snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc1 [ 1.490485] i2c /dev entries driver [ 1.494580] bd7181x-power bd7181x-power: battery_cycle = 0 [ 1.500703] Status Register 1 == 0x0 [ 1.504742] Status Register 2 == 0x0 [ 1.508741] Status Register 3 == 0x40 [ 1.512845] Status Register 4 == 0x0 [ 1.516844] Status Register 5 == 0x80 [ 1.520926] Status Register 6 == 0x0 [ 1.524943] Status Register 7 == 0x0 [ 1.528938] Status Register 8 == 0x2 [ 1.532951] Status Register 9 == 0x0 [ 1.536948] Status Register 10 == 0x0 [ 1.541032] Status Register 11 == 0x0 [ 1.545133] Status Register 12 == 0x0 [ 1.551723] errflags = 1 [ 1.554264] bit0 is set [RESET REASONS]: SOFTWARE_RESTART: Software Initiated System Restart [ 1.579455] imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0) imx2_wdt.base=0xa0920000 base pa:0x20bc000 imx2_wdt.clk=0x9a00c100 [ 1.594224] cpuidle: using governor ladder [ 1.598350] cpuidle: using governor menu [ 1.602447] sdhci: Secure Digital Host Controller Interface driver [ 1.608650] sdhci: Copyright(c) Pierre Ossman [ 1.613046] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.623700] mmc1: no vqmmc regulator found [ 1.627811] mmc1: Not allowing HS200 [ 1.631397] mmc1: no vmmc regulator found [ 1.681574] mmc1: SDHCI controller on 2190000.usdhc [2190000.usdhc] using DMA [ 1.692212] mmc0: no vqmmc regulator found [ 1.696322] mmc0: Not allowing HS200 [ 1.699908] mmc0: no vmmc regulator found [ 1.741568] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using DMA [ 1.750831] usbcore: registered new interface driver usbhid [ 1.756458] usbhid: USB HID core driver [ 1.761320] NET: Registered protocol family 26 [ 1.768033] TCP: cubic registered [ 1.771362] IPv6: Loaded, but administratively disabled, reboot required to enable [ 1.778986] sit: IPv6 over IPv4 tunneling driver [ 1.784103] NET: Registered protocol family 17 [ 1.790668] 8021q: 802.1Q VLAN Support v1.8 [ 1.798989] Key type dns_resolver registered VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 1.835816] ldo5: disabling [ 1.844605] ldo4: disabling [ 1.847816] regulator-dummy: disabling [ 1.851822] imx mcc test is registered. [ 1.856492] bd7181x-rtc bd7181x-rtc: setting system clock to 2001-01-06 22:51:39 UTC (978821499) [ 1.868952] ALSA device list: [ 1.874027] No soundcards found. [ 1.878647] Freeing unused kernel memory: 1444K (80719000 - 80882000) 3.10.53-lab126 #1 PREEMPT Fri Jul 22 00:45:40 PDT 2016 armv7l [ 2.095862] mmc0: BKOPS_EN bit is not set [ 2.118099] mmc0: new high speed DDR MMC card at address 0001 [ 2.124179] mmcblk0: mmc0:0001 NJ2ZMB 3.64 GiB [ 2.128809] mmcblk0boot0: mmc0:0001 NJ2ZMB partition 1 4.00 MiB [ 2.134851] mmcblk0boot1: mmc0:0001 NJ2ZMB partition 2 4.00 MiB [ 2.140855] mmcblk0rpmb: mmc0:0001 NJ2ZMB partition 3 512 KiB [ 2.147344] mmcblk0: p1 p2 p3 p4 [ 2.153286] mmcblk0boot1: unknown partition table [ 2.159917] mmcblk0boot0: unknown partition table [ 2.198230] INFO:child exited with status 00000000 [ 2.203576] INFO:find_file:118 Found V220_C283_BDB501_ED060SCSU1_TC.wrf.gz ERROR:wfm_count=1 [ 2.212560] mxc_epdc_eink: module license 'proprietary' taints kernel. [ 2.219276] Disabling lock debugging due to kernel taint [ 2.224992] INFO:Loaded module /lib/modules/mxc_epdc_eink.ko (11172 bytes) Panel VCOM string: 2690 [ 2.236191] imx_epdc_fb 20f4000.epdc: vcom_steps 125 [ 2.241350] imx_epdc_fb 20f4000.epdc: Memory override detected TotalMem:512M X:800 Y:600 FBMem:6M [ 2.257336] imx_epdc_fb 20f4000.epdc: EPDC version = 2.1.0 [ 2.324232] wv_file->wdh.luts & 0xC =4 [ 4.164619] INFO:Loaded module /lib/modules/mxc_epdc_fb.ko (79696 bytes) [ 4.448816] INFO:eink initialized... (486400 bytes) Press [ENTER] for recovery menu... 0 /[ 4.472283] INFO:!!! Checking MBR /dev/mmcblk0 !!!! [ 4.485638] INFO:partition 2, start sector is 987136 [ 4.490676] INFO:partition 3, start sector is 1118208 [ 4.495853] INFO:partition 4, start sector is 1249280 [ 4.500957] INFO:maximizing partition 6385664 sectors [ 4.506057] INFO:*** Partition table verified for /dev/mmcblk0 *** [ 4.513485] INFO:Loaded module /lib/modules/libcomposite.ko (45712 bytes) [ 4.521733] g_mass_storage gadget: Mass Storage Function, version: 2009/09/11 [ 4.528879] g_mass_storage gadget: Number of LUNs=1 [ 4.533840] lun0: LUN: removable file: (no medium) [ 4.538734] fsg_bind:3212 [ 4.541367] g_mass_storage gadget: Internal Storage, version: 2009/09/11 [ 4.548095] g_mass_storage gadget: userspace failed to provide iSerialNumber [ 4.555158] g_mass_storage gadget: g_mass_storage ready [ 4.560487] INFO:Loaded module /lib/modules/g_mass_storage.ko removable=1 idVendor=0x1949 idProduct=0x0004 recovery_mode=1 (41120 bytes) [ 4.854544] usb_gadget_state_work: gadget state: addresssed [ 4.900895] g_mass_storage gadget: high-speed config #1: Linux File-Backed Storage [ 4.908516] usb_gadget_state_work: gadget state: configured [ 4.914121] send_online_uevent:432 fsg_ 0x0 recovery_mode:1 Charge: 98% [##########################################################] Menu ==== 3. Load MMC0 over USB storage 4. Erase MMC0 I. Initialize Partition Table (fdisk) and format FAT O. Format and overwrite FAT partition E. Export FAT partition U. Update using update*.bin file on FAT partition M. Update using update*.bin file on FAT partition of second MMC port D. dmesg / kernel printk ring buffer. Q. quit Choose: 10 / Charge: 98% [##########################################################] Menu ==== 3. Load MMC0 over USB storage 4. Erase MMC0 I. Initialize Partition Table (fdisk) and format FAT O. Format and overwrite FAT partition E. Export FAT partition U. Update using update*.bin file on FAT partition M. Update using update*.bin file on FAT partition of second MMC port D. dmesg / kernel printk ring buffer. Q. quit Choose: 10 / Charge: 98% [##########################################################] Menu ==== 3. Load MMC0 over USB storage 4. Erase MMC0 I. Initialize Partition Table (fdisk) and format FAT O. Format and overwrite FAT partition E. Export FAT partition U. Update using update*.bin file on FAT partition M. Update using update*.bin file on FAT partition of second MMC port D. dmesg / kernel printk ring buffer. Q. quit Choose: 10 / Charge: 98% [##########################################################] Menu ==== 3. Load MMC0 over USB storage 4. Erase MMC0 I. Initialize Partition Table (fdisk) and format FAT O. Format and overwrite FAT partition E. Export FAT partition U. Update using update*.bin file on FAT partition M. Update using update*.bin file on FAT partition of second MMC port D. dmesg / kernel printk ring buffer. Q. quit Choose: 10 / Charge: 98% [##########################################################] Menu ==== 3. Load MMC0 over USB storage 4. Erase MMC0 I. Initialize Partition Table (fdisk) and format FAT O. Format and overwrite FAT partition E. Export FAT partition U. Update using update*.bin file on FAT partition M. Update using update*.bin file on FAT partition of second MMC port D. dmesg / kernel printk ring buffer. Q. quit Choose: 10 / Charge: 98% [##########################################################] Menu ==== 3. Load MMC0 over USB storage 4. Erase MMC0 I. Initialize Partition Table (fdisk) and format FAT O. Format and overwrite FAT partition E. Export FAT partition U. Update using update*.bin file on FAT partition M. Update using update*.bin file on FAT partition of second MMC port D. dmesg / kernel printk ring buffer. Q. quit Choose: 10 / Charge: 98% [##########################################################] Menu ==== 3. Load MMC0 over USB storage 4. Erase MMC0 I. Initialize Partition Table (fdisk) and format FAT O. Format and overwrite FAT partition E. Export FAT partition U. Update using update*.bin file on FAT partition M. Update using update*.bin file on FAT partition of second MMC port D. dmesg / kernel printk ring buffer. Q. quit Choose: 10 / Charge: 98% [##########################################################] Menu ==== 3. Load MMC0 over USB storage 4. Erase MMC0 I. Initialize Partition Table (fdisk) and format FAT O. Format and overwrite FAT partition E. Export FAT partition U. Update using update*.bin file on FAT partition M. Update using update*.bin file on FAT partition of second MMC port D. dmesg / kernel printk ring buffer. Q. quit Choose: 5 - Charge: 98% [##########################################################] Menu ==== 3. Load MMC0 over USB storage 4. Erase MMC0 I. Initialize Partition Table (fdisk) and format FAT O. Format and overwrite FAT partition E. Export FAT partition U. Update using update*.bin file on FAT partition M. Update using update*.bin file on FAT partition of second MMC port D. dmesg / kernel printk ring buffer. Q. quit Choose: 8 \ Charge: 98% [##########################################################] Menu ==== 3. Load MMC0 over USB storage 4. Erase MMC0 I. Initialize Partition Table (fdisk) and format FAT O. Format and overwrite FAT partition E. Export FAT partition U. Update using update*.bin file on FAT partition M. Update using update*.bin file on FAT partition of second MMC port D. dmesg / kernel printk ring buffer. Q. quit Choose: 7 | Charge: 98% [##########################################################] Menu ==== 3. Load MMC0 over USB storage 4. Erase MMC0 I. Initialize Partition Table (fdisk) and format FAT O. Format and overwrite FAT partition E. Export FAT partition U. Update using update*.bin file on FAT partition M. Update using update*.bin file on FAT partition of second MMC port D. dmesg / kernel printk ring buffer. Q. quit Choose: 7 |u uu /dev/mmcblk0p4: CHS=4/16/99776 size=3269459968[ 21.333659] INFO:Setup loop device /dev/loop0 for /dev/mmcblk0p4 + 8192 bytes flag type first last lba first lba size Pa[ 21.346160] FAT-fs (loop0): Volume was not safely ejected. Run fsck to correct. rtition p1: 0x00 0x0b 16[ 21.356693] INFO:find_file:118 Found update.bin <large> 16 6385648 CHS: 0/1/1 - <large> Par[ 21.366385] INFO:Skipping battery charge check tition p2: Partition p3: Partit[ 21.373361] INFO:Found bundle /mnt-us/update.bin ion p4: [ 21.380805] INFO:*** NORMAL MODE [ 21.467619] *** CHECKING /mnt-us/update.bin *** [ 22.288490] INFO:do_unbundle: filename=/mnt-us/update.bin, new_file=0x0001534c [ 22.314716] INFO:Unsigned bundle. [ 22.335159] IGNORING FILE: update-J8-heisenberg_eanab-044.dat update-J8-heisenberg_eanab-044.dat:128 6d4333bf8eb2639a8d84e1eec0c39eb7 imx6sl_heisenberg/u-boot.bin 3 bootloader_bin 1 a862af7d56828c87721fb58e41621b3b imx6sl_heisenberg/uImage 38 main_kernel 128 4357d531d7e5396db90cfe752d7398d7 rootfs.img.gz 1669 update_image_rootfs 128 70783fa7689c34aead7d47a3826dcb9d data.stgz demo_data.stgz voice_data.stgz 4195 update_data_data update-J8-heisenberg_eanab-044.dat:EOF [ 22.376364] INFO:Total progress is 1% imx6sl_heisenberg/u-boot.bin 26CHK: imx6sl_heisenberg/u-boot.bin 1957 [#######################hash for UBoot: imx6sl_heisenberMD5: g/u-boot.bin 447684 [########6d##############################] 4333bf8eb2639a8d84e1eec0c39eb7 SHA256: 1972c18868b5e1965a4ab727bc0e6cb3ecf75547888cb951b03107ce8afe3276 [ 22.410703] SIGNATURE FILE: imx6sl_heisenberg/u-boot.bin.sig [ 22.416564] INFO:Total progress is 1% [ 22.420413] INFO:imx6sl_heisenberg/u-boot.bin.sig:sig_len=256 imx6sl_heisenberg/uImage 4980736 [###########################[ 22.866945] INFO:Total progress is 3% ###########]CHK: imx6sl_heisenberg/uImage hash for UImage: MD5: a862af7d56828c87721fb58e41621b3b SHA256: 4276486b6781af591eff66eb10c2c2243de111c005af3bf4c8e397a1209a53e9 [ 22.889509] SIGNATURE FILE: imx6sl_heisenberg/uImage.sig [ 22.895023] INFO:Total progress is 3% [ 22.898870] INFO:imx6sl_heisenberg/uImage.sig:sig_len=256 rootfs.img.gz 218795861 [##############################[ 38.247960] INFO:Total progress is 13% ########]CHK: rootfs.img.gz hash for RootFS: MD5: 4357d531d7e5396db90cfe752d7398d7 SHA256: e9eeb676077e3899aec724d5b7e99bf16d6cb561b75f5aebfffb14dda09eb6e7 [ 38.268311] SIGNATURE FILE: rootfs.img.gz.sig [ 38.272872] INFO:Total progress is 13% [ 38.276801] INFO:rootfs.img.gz.sig:sig_len=256 data.stgz 549898743 [###############################[ 76.214805] INFO:Total progress is 18% #######]CHK: data.stgz hash for Userdata: MD5: 18dc2c052d78e15edecc7cf283eb9d3f SHA256: 0b6d55d7efea941f943f9f95e371f1be1b941878b300830af4aabfe32cd791f7 [ 76.234642] SIGNATURE FILE: data.stgz.sig [ 76.238837] INFO:Total progress is 18% [ 76.242826] INFO:data.stgz.sig:sig_len=256 [ 76.246953] SIGNATURE FILE: update-J8-heisenberg_eanab-044.dat.sig [ 76.253313] IGNORING SIGNATURE FILE: update-J8-heisenberg_eanab-044.dat.sig [ 76.260984] INFO:*** bundle sizes: UImage[4980736 / 14680064], RootFS[460800000 / 471859200], UBoot[447684 / 458752], DiagsFS[0 / 67108864], Diags Kernel[0 / 14680064], Userdata[549898743 / 2212356096], fbios[0 / 0], sbios[0 / 0] [ 76.282302] ERROR: signature is not the correct length (128 bytes versus 256 bytes) [ 76.292517] INFO:UImage:Present siglen=256 sigpassed=Yes [ 76.297881] ERROR: signature is not the correct length (128 bytes versus 256 bytes) [ 76.308063] INFO:RootFS:Present siglen=256 sigpassed=Yes [ 76.313457] ERROR: signature is not the correct length (128 bytes versus 256 bytes) [ 76.323625] INFO:UBoot:Present siglen=256 sigpassed=Yes [ 76.328856] INFO:DiagsFS:missing [ 76.332103] INFO:Diags Kernel:missing [ 76.335813] ERROR: signature is not the correct length (128 bytes versus 256 bytes) [ 76.345971] INFO:Userdata:Present siglen=256 sigpassed=Yes [ 76.351462] INFO:fbios:missing [ 76.354534] INFO:sbios:missing [ 76.357601] *** UPDATING /mnt-us/update.bin (Attempt #1) *** [ 76.363321] INFO:do_unbundle: filename=/mnt-us/update.bin, new_file=0x000163fc [ 76.392269] INFO:Updating imx6sl_heisenberg/u-boot.bin imx6sl_heisenberg/u-boot.bin 447684 [#######################[ 76.436691] INFO:Total progress is 21% ###############] [ 76.442688] INFO:imx6sl_heisenberg/u-boot.bin update successful [ 76.450105] INFO:Updating imx6sl_heisenberg/uImage imx6sl_heisenberg/uImage 4980736 [###########################[ 76.912438] INFO:Total progress is 23% ###########] [ 76.918314] INFO:imx6sl_heisenberg/uImage update successful rootfs.img.gz 218795861 [###############################[ 133.527382] INFO:Total progress is 90% #######] [ 133.691268] INFO:rootfs.img.gz update successful [ 133.696485] INFO:Updating data.stgz data.stgz 549898743 [######################################][ 241.049088] INFO:Total progress is 100% [ 241.054174] INFO:data.stgz update successful [ 241.059096] INFO:Installation had uImage. Installing it. [ 241.064821] INFO:Copying /uImage to /dev/mmcblk0 ... 4980736 [######################################] [ 246.049907] INFO:Copying /uboot to /dev/mmcblk0boot0 ... 447684 [ 246.088019] FAT-fs (loop0): Volume was not safely ejected. Run fsck to correct. [################################[ 246.095624] INFO:removing /mnt-us/update.bin ######] [ 246.275696] INFO:bundle /mnt-us/update.bin was successful Charge: 98% [##########################################################] Menu ==== 3. Load MMC0 over USB storage 4. Erase MMC0 I. Initialize Partition Table (fdisk) and format FAT O. Format and overwrite FAT partition E. Export FAT partition U. Update using update*.bin file on FAT partition M. Update using update*.bin file on FAT partition of second MMC port D. dmesg / kernel printk ring buffer. Q. quit Choose: 1 - [ 257.474610] fsg_disable:2563 Menu timeout [ 257.477652] send_offline_uevent:407 fsg_ 0x2 unsafe 1 recovery_mode:1 [ 257.485469] fsg_unbind:3175 [ 257.488290] send_offline_uevent:407 fsg_ 0x2 unsafe 1 recovery_mode:1 [ 257.503474] usb_gadget_state_work: gadget state: not attached [ 257.509414] INFO:storage_shutdown: done with g_mass_storage [ 257.515193] INFO:storage_shutdown: done with libcomposite BOOTING DEFAULT. IP-Config: no devices to configure [ 258.360567] kjournald starting. Commit interval 5 seconds [ 258.366265] EXT3-fs (mmcblk0p2): using internal journal [ 258.372071] EXT3-fs (mmcblk0p2): recovery complete [ 258.376869] EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode kinit: Mounted root (ext3 filesystem). init started: BusyBox v1.17.1 (2016-07-22 00:36:46 PDT) starting pid 89, tty '': '/etc/init.d/rcS' /etc/init.d/rcS: line 89: boot_milestone: not found system: I rcS:def:starting /etc/rcS.d/S50diags USER=root prevlevel=N HOME=/ runlevel=S TERM=vt102 PATH=/sbin:/bin:/usr/sbin:/usr/bin:/usr/local/bin SHELL=/bin/sh PWD=/ VERBOSE=no READ_AHEAD=4 USER=root prevlevel=N HOME=/ runlevel=S TERM=vt102 PATH=/sbin:/bin:/usr/sbin:/usr/bin:/usr/local/bin SHELL=/bin/sh PWD=/ VERBOSE=no IO_SCHED=anticipatory USER=root prevlevel=N HOME=/ runlevel=S TERM=vt102 PATH=/sbin:/bin:/usr/sbin:/usr/bin:/usr/local/bin SHELL=/bin/sh PWD=/ VERBOSE=no TMP_SIZE=32M info firsttime:mount_rw:time=258690:Mounting root RW for first boot info firsttime:cursor:Linking Xorg cursor: ln: /usr/share/fonts/X11/misc/cursor.pcf: No such file or directory info firsttime:mount_ro:time=258730:Mounting root RO [ 258.791986] elevator: type not found [ 258.795660] elevator: switch to failed [ 258.805088] elevator: type not found [ 258.808762] elevator: switch to failed [ 258.818109] elevator: type not found [ 258.821846] elevator: switch to failed [ 258.831136] elevator: type not found [ 258.834991] elevator: switch to failed info system:start:time=258839: /etc/rcS.d/S50diags: line 572: f_proto: not found info hardware:no_wan::WiFi only device. No WAN found info system:config:platform=heisenberg,board=eanab,rev=17,proto=N,wifi=Y,wan=N: [ 258.893023] udevd (194): /proc/194/oom_adj is deprecated, please use /proc/194/oom_score_adj instead. info system:done:time=259279: [ 259.309781] fuse init (API version 7.22) FATAL: Module ppp_async not found. TI [ 259.356964] Zforce2 regulator is not enabled! Enabling Zforce2 touch regulator... [ 259.366186] Zforce2 touch regulator is enabled! [ 259.433032] input: zforce2 as /devices/platform/zforce2.0/input/input0 /etc/rcS.d/S50diags: line 572: iptables-restore: not found /etc/rcS.d/S50diags: line 572: /opt/ar6k/host/recEvent: not found [ 259.672315] kjournald starting. Commit interval 5 seconds [ 259.677903] EXT3-fs (mmcblk0p3): using internal journal [ 259.692230] EXT3-fs (mmcblk0p3): recovery complete [ 259.697033] EXT3-fs (mmcblk0p3): mounted filesystem with ordered data mode info userstore:run:time=259779,action=start: info userstore:start:found_bootup_flag:Found BOOTUP flag file dosfsck 2.11 (12 Mar 2005) dosfsck 2.11, 12 Mar 2005, FAT32, LFN Checking we can access the last sector of the filesystem Clearing dirty flag Boot sector contents: System ID "mkdosfs" Media byte 0xf8 (hard disk) 512 bytes per logical sector 8192 bytes per cluster 2134 reserved sectors First FAT starts at byte 1092608 (sector 2134) 2 FATs, 32 bit entries 1594880 bytes per FAT (= 3115 sectors) Root directory start at cluster 2 (arbitrary size) Data area starts at byte 4282368 (sector 8364) 398580 data clusters (3265167360 bytes) 32 sectors/track, 64 heads 0 hidden sectors 6385648 sectors total Checking for unused clusters. Checking free cluster summary. Performing changes. /dev/loop/0: 526 files, 101345/398580 clusters info mntus:fs_error_recover::File system errors recovered info userstore:found_data::found data.stgz info bundlefuncs:parse_bundle:BundleType=SP01: err bundlefuncs:verify_bundle:invalid bundle signature: info userstore:extract_data::verify_bundle failed RET=127 err userstore:extract_data_failed::extracting data.stgz failed. Ret=127 info filesystems:createWifiSymLink:Cannot find the script to create the Wifi symbolic link: system: I mntroot:def:Making root filesystem writeable [ 261.055289] EXT3-fs (mmcblk0p2): using internal journal ln: /usr/local/sbin/dropbear: File exists ln: /usr/local/sbin/dropbearkey: File exists /etc/rcS.d/S50diags: line 13: /usr/local/sbin/dropbearkey: not found system: I mntroot:def:Making root filesystem read-only /etc/rcS.d/S50diags: line 13: /usr/local/sbin/dropbear: not found system: I mntroot:def:Making root filesystem writeable [ 261.161827] EXT3-fs (mmcblk0p2): using internal journal system: I mntroot:def:Making root filesystem writeable mounting waveform filesystem [ 261.240200] FAT-fs (loop1): Volume was not safely ejected. Run fsck to correct. rm: can't remove '/lib/firmware/imx/epdc_EANAB.fw': No such file or directory system: I mntroot:def:Making root filesystem read-only info display:started:time=261320: USER=root prevlevel=N OLDPWD=/ HOME=/ runlevel=S TERM=vt102 PATH=/sbin:/bin:/usr/sbin:/usr/bin:/usr/local/bin SHELL=/bin/sh PWD=/dev VERBOSE=no LD_LIBRARY_PATH=/usr/lib/tts/speech/components/common/:/usr/lib/tts /etc/rcS.d/S50diags: line 13: kb: not found system: I mntroot:def:Making root filesystem writeable [ 261.412134] EXT3-fs (mmcblk0p2): using internal journal Reduce the voltage I2C write 0x4B: cmd:0x09 value:0x92 I2C write 0x4B: cmd:0x07 value:0xD0 Do md5sum test 1 2 3 4 5 md5sum test pass, voltage test pass.... restore the voltage setting I2C write 0x4B: cmd:0x07 value:0xD1 I2C write 0x4B: cmd:0x09 value:0x93 Test done Config USB adb mode [ 265.288455] file system registered [ 265.299142] android_usb gadget: Mass Storage Function, version: 2009/09/11 [ 265.306444] android_usb gadget: Number of LUNs=1 [ 265.311074] lun0: LUN: removable file: (no medium) [ 265.318395] android_usb gadget: android_usb ready [ 265.528897] android_work: sent uevent USB_STATE=CONNECTED [ 265.535744] android_work: sent uevent USB_STATE=DISCONNECTED [ 265.617801] usb_gadget_state_work: gadget state: addresssed [ 265.638209] android_work: sent uevent USB_STATE=CONNECTED [ 265.765896] android_work: sent uevent USB_STATE=DISCONNECTED [ 265.849445] android_work: sent uevent USB_STATE=CONNECTED [ 265.855692] android_work: sent uevent USB_STATE=DISCONNECTED [ 265.937757] usb_gadget_state_work: gadget state: addresssed [ 265.958265] android_work: sent uevent USB_STATE=CONNECTED [ 266.085746] android_work: sent uevent USB_STATE=DISCONNECTED [ 266.169383] android_work: sent uevent USB_STATE=CONNECTED [ 266.175635] android_work: sent uevent USB_STATE=DISCONNECTED [ 266.257767] usb_gadget_state_work: gadget state: addresssed [ 266.278157] android_work: sent uevent USB_STATE=CONNECTED [ 266.401104] usb_gadget_state_work: gadget state: suspended [ 267.335693] android_usb: already disabled using port=5555[ 267.345883] read descriptors [ 267.349807] read strings [ 272.348863] usb_gadget_state_work: gadget state: suspended diags : /opt/factory/rootfs_md5_list not found. ln: /usr/sbin/dtest: File exists ln: /usr/sbin/inventory: File exists /etc/init.d/rcS: line 125: boot_milestone: not found starting pid 622, tty '': '/bin/sh /etc/getty-diags' starting battery regulation min: 71 max: 73 Value:0, /sys/class/power_supply/bd7181x_bat/charging [ 272.459532] android_work: sent uevent USB_STATE=DISCONNECTED [ 272.548763] android_work: sent uevent USB_STATE=CONNECTED [ 272.555034] android_work: sent uevent USB_STATE=DISCONNECTED [ 272.637250] usb_gadget_state_work: gadget state: addresssed [ 272.657790] android_work: sent uevent USB_STATE=CONNECTED [ 272.690022] android_usb gadget: high-speed config #1: android [ 272.696147] usb_gadget_state_work: gadget state: configured [ 272.702492] android_work: sent uevent USB_STATE=CONFIGURED Welcome to Kindle! kindle login: root root Password: mario ################################################# # N O T I C E * N O T I C E * N O T I C E # ################################################# Rootfs is mounted read-only. Invoke mntroot rw to switch back to a writable rootfs. ################################################# [root@kindle root]# reboot reboot The system is going down NOW! Sent SIGTERM to all processes Terminated Requesting system rebootesses [ 290.521904] brcm_wlan_free_mem: static buffers freed [ 290.527673] imx2-wdt 20bc000.wdog: Device shutdown: Expect reboot! [ 290.533942] Restarting system. [ 290.537193] arch_reset_special_mode: cmd: (null) [ 290.541855] set_boot_mode: mode: d [ 290.545279] to write to register [ 290.548512] read out: 13 U-Boot 2014.04 (Jun 04 2016 - 11:52:07) CPU: Freescale i.MX6SL rev1.3 at 792 MHz CPU: Temperature 39 C, calibration data: 0x58d50a5f Reset cause: POR FRED::: EXTCSD177=0, 179=48FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Board: Heisenberg Board Id: P00118077373003J S/N: G000K905738108UK I2C: ready DRAM: MR5=0x1,MR6=0x4 512 MiB WARNING: Caches not enabled MMC: FRED::: EXTCSD177=0, 179=48FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial REBOOTMODE: 0 using default bootcmdNormal Boot Hit any key to stop autoboot: 0 mmc1(part 0) is current device FRED::: EXTCSD177=0, 179=48BOOTing from mmc ... mmc1(part 0) is current device MMC read: dev # 1, block # 720, count 28672 ... 28672 blocks read in 319 msec: OK MMC read: dev # 1, block # 520, count 256 ... 256 blocks read in 7 msec: OK ## Booting kernel from Legacy Image at 80800000 ... Image Name: Linux-3.10.53-lab126 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4786328 Bytes = 4.6 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Loading Kernel Image ... OK Loading Device Tree to 9fcae000, end 9fcb85ef ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 3.10.53-lab126 (jenkins-official@sjc10-jbuild09.sjc10.amazon.com) (collect2: error: ld returned 1 exit status) #1 PREEMPT Sat Jun 4 12:16:28 PDT 2016 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Freescale i.MX6 SoloLite (Device Tree), model: Heisenberg P0 [ 0.000000] printk_reserve_buf:863 log_goal_location:0x8fff0000 log_worst_location:0x8fef0000 new_log_buf_len:32768 [ 0.000000] printk_reserve_buf:883 printk log placed at 8fff0000 [ 0.000000] cma: CMA: reserved 32 MiB at 9c000000 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttymxc0,115200 root=/dev/mmcblk0p1 rootwait rw uart_at_4M [ 0.000000] Prink buffer will be relocated to physical address: 8fff0000 va: 00000000 new_log_buf_len:32768 [ 0.000000] Prink buffer will be relocated to physical address: 8fff0000 va: 8fff0000 new_log_buf_len:32768 [ 0.000000] log_buf_len: 32768 [ 0.000000] early log buf free: 30752(93%) [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 512MB = 512MB total [ 0.000000] Memory: 477608k/477608k available, 46680k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xa0800000 - 0xff000000 (1512 MB) lowmem : 0x80000000 - 0xa0000000 ( 512 MB) pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) modules : 0x7f000000 - 0x7fe00000 ( 14 MB) .text : 0x80008000 - 0x80717760 (7230 kB) .init : 0x80718000 - 0x808811fc (1445 kB) .data : 0x80882000 - 0x808c7e80 ( 280 kB) .bss : 0x808c7e80 - 0x808f0988 ( 163 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L310 cache controller enabled [ 0.000000] l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x32030000, Cache size: 262144 B [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000469] Calibrating delay loop... 789.70 BogoMIPS (lpj=3948544) [ 0.040132] pid_max: default: 32768 minimum: 301 [ 0.040272] Mount-cache hash table entries: 512 [ 0.044692] CPU: Testing write buffer coherency: ok [ 0.044918] Setting up static identity map for 0x80524150 - 0x805241a8 [ 0.045691] devtmpfs: initialized [ 0.047430] pinctrl core: initialized pinctrl subsystem [ 0.047680] regulator-dummy: no parameters [ 0.049794] NET: Registered protocol family 16 [ 0.057062] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.057660] LAB126 Board id - P00118077373003J [ 0.057741] Use WDOG1 as reset source [ 0.063154] syscon 20c8000.anatop: regmap [mem 0x020c8000-0x020c8fff] registered [ 0.063407] vdd1p1: 800 <--> 1375 mV at 1100 mV [ 0.063693] vdd3p0: 2625 <--> 3400 mV at 3000 mV [ 0.063982] vdd2p5: 2100 <--> 2850 mV at 2500 mV [ 0.064343] cpu: 725 <--> 1450 mV at 1100 mV [ 0.064612] vddpu: 725 <--> 1450 mV [ 0.064974] vddsoc: 725 <--> 1450 mV at 1175 mV [ 0.066832] syscon 20e0000.iomuxc-gpr: regmap [mem 0x020e0000-0x020e0037] registered [ 0.068877] syscon 21bc000.ocotp-ctrl: regmap [mem 0x021bc000-0x021bffff] registered [ 0.070733] amp_boost_enable:iMX:MAX98090:BOARD [ 0.070766] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.070776] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.074195] imx6sl-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.079240] bio: create slab <bio-0> at 0 [ 0.080427] SCSI subsystem initialized [ 0.080649] usbcore: registered new interface driver usbfs [ 0.080707] usbcore: registered new interface driver hub [ 0.080835] usbcore: registered new device driver usb [ 0.082179] bd7181x 0-004b: IRQ 276 GPIO 116 [ 0.087668] buck1: 800 <--> 2000 mV at 1300 mV [ 0.088852] buck2: 800 <--> 2000 mV at 1300 mV [ 0.089674] buck3: 1200 <--> 2700 mV at 1800 mV [ 0.090497] buck4: 1100 <--> 1850 mV at 1200 mV [ 0.091290] buck5: 1800 <--> 3300 mV at 3200 mV [ 0.092106] ldo1: 800 <--> 3300 mV at 3200 mV [ 0.092896] ldo2: 800 <--> 3300 mV at 3200 mV [ 0.094113] ldo3: 3000 mV [ 0.094724] ldo4: 800 <--> 3300 mV at 3200 mV [ 0.095302] ldo5: 800 <--> 3300 mV at 1800 mV [ 0.095870] dvref: 3000 mV [ 0.096006] lpsr: 1800 mV [ 0.096583] wled: at 0 mV 0 <--> 25 mA at 0 mA [ 0.097469] i2c i2c-0: IMX I2C adapter registered [ 0.098087] i2c i2c-1: IMX I2C adapter registered [ 0.098365] i2c i2c-2: IMX I2C adapter registered [ 0.098477] pps_core: LinuxPPS API ver. 1 registered [ 0.098487] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.098511] PTP clock support registered [ 0.098863] MIPI CSI2 driver module loaded [ 0.098941] Advanced Linux Sound Architecture Driver Initialized. [ 0.099574] cfg80211: Calling CRDA to update world regulatory domain [ 0.099610] cfg80211: World regulatory domain updated: [ 0.099619] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 0.099630] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 0.099640] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 0.099649] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 0.099658] cfg80211: (5140000 KHz - 5360000 KHz @ 40000 KHz), (N/A, 3000 mBm) [ 0.099666] cfg80211: (5460000 KHz - 5860000 KHz @ 40000 KHz), (N/A, 3000 mBm) [ 0.100865] pureg-dummy: no parameters [ 0.101494] Switching to clocksource mxc_timer1 [ 0.109381] NET: Registered protocol family 2 [ 0.110065] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.110145] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.110196] TCP: Hash tables configured (established 4096 bind 4096) [ 0.110320] TCP: reno registered [ 0.110339] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.110359] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.110563] NET: Registered protocol family 1 [ 0.110818] RPC: Registered named UNIX socket transport module. [ 0.110830] RPC: Registered udp transport module. [ 0.110838] RPC: Registered tcp transport module. [ 0.110845] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.117378] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available [ 0.118006] ldo2p5-dummy: no parameters [ 0.118757] Bus freq driver module loaded [ 0.119209] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.124598] VFS: Disk quotas dquot_6.5.2 [ 0.124751] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.127060] NFS: Registering the id_resolver key type [ 0.127103] Key type id_resolver registered [ 0.127114] Key type id_legacy registered [ 0.127154] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.127669] msgmni has been set to 996 [ 0.130598] io scheduler noop registered [ 0.130613] io scheduler deadline registered [ 0.130655] io scheduler cfq registered (default) [ 0.137456] Serial: IMX driver [ 0.137776] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX [ 0.841402] console [ttymxc0] enabled [ 0.845552] 2034000.serial: ttymxc2 at MMIO 0x2034000 (irq = 60) is a IMX [ 0.852755] imx6sl-pinctrl 20e0000.iomuxc: pin MX6SL_PAD_SD1_DAT4 already requested by 20e0000.iomuxc; cannot claim for 2038000.serial [ 0.864890] imx6sl-pinctrl 20e0000.iomuxc: pin-145 (2038000.serial) status -22 [ 0.872143] imx6sl-pinctrl 20e0000.iomuxc: could not request pin 145 on device 20e0000.iomuxc [ 0.880680] imx-uart 2038000.serial: Error applying setting, reverse things back [ 0.888167] 2038000.serial: ttymxc3 at MMIO 0x2038000 (irq = 61) is a IMX [ 0.895487] serial: Freescale lpuart driver [ 0.900580] Registering Heisenberg hall sensor platform device [ 0.907665] imx sema4 driver is registered. [ 0.916839] brd: module loaded [ 0.922617] loop: module loaded bt_pwrctrl_init called.. [ 0.928145] bt_reset pin obtained is 51 [ 0.932386] bt_dev_wake pin obtained is 138 [ 0.936756] bt_host_wake pin obtained is 93 [ 0.941134] IRQ# for BT HOST WAKE: 253 bt_pwrctrl_probe probe successful [ 0.950086] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.956913] usbcore: registered new interface driver usb-storage [ 0.963929] imx6sl-pinctrl 20e0000.iomuxc: pin MX6SL_PAD_EPDC_PWRCOM already requested by 20e0000.iomuxc; cannot claim for 2184000.usb [ 0.976073] imx6sl-pinctrl 20e0000.iomuxc: pin-56 (2184000.usb) status -22 [ 0.982981] imx6sl-pinctrl 20e0000.iomuxc: could not request pin 56 on device 20e0000.iomuxc [ 0.991432] imx_usb 2184000.usb: Error applying setting, reverse things back [ 1.002724] usb_gadget_state_work: gadget state: not attached [ 1.451552] imx_usb 2184000.usb: vbus is error [ 1.456013] imx_usb 2184000.usb: Error occurs during detection: -22 [ 1.462789] mousedev: PS/2 mouse device common for all mice [ 1.474304] bd7181x-rtc bd7181x-rtc: rtc core: registered bd7181x-rtc as rtc0 [ 1.482029] snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp as rtc1 [ 1.490420] i2c /dev entries driver [ 1.494514] bd7181x-power bd7181x-power: battery_cycle = 0 [ 1.500633] Status Register 1 == 0x0 [ 1.504673] Status Register 2 == 0x0 [ 1.508673] Status Register 3 == 0x40 [ 1.512776] Status Register 4 == 0x0 [ 1.516774] Status Register 5 == 0x80 [ 1.520855] Status Register 6 == 0x0 [ 1.524869] Status Register 7 == 0x0 [ 1.528866] Status Register 8 == 0x2 [ 1.532877] Status Register 9 == 0x0 [ 1.536876] Status Register 10 == 0x0 [ 1.540959] Status Register 11 == 0x0 [ 1.545057] Status Register 12 == 0x0 [ 1.551611] errflags = 1 [ 1.554153] bit0 is set [RESET REASONS]: SOFTWARE_RESTART: Software Initiated System Restart [ 1.579037] imx2-wdt 20bc000.wdog: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=0) imx2_wdt.base=0xa0920000 base pa:0x20bc000 imx2_wdt.clk=0x9a00c100 [ 1.593803] cpuidle: using governor ladder [ 1.597931] cpuidle: using governor menu [ 1.602029] sdhci: Secure Digital Host Controller Interface driver [ 1.608234] sdhci: Copyright(c) Pierre Ossman [ 1.612631] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.623097] mmc1: no vqmmc regulator found [ 1.627357] mmc1: Not allowing HS200 [ 1.630971] mmc1: no vmmc regulator found [ 1.681549] mmc1: SDHCI controller on 2190000.usdhc [2190000.usdhc] using DMA [ 1.692190] mmc0: no vqmmc regulator found [ 1.696302] mmc0: Not allowing HS200 [ 1.699889] mmc0: no vmmc regulator found [ 1.741545] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using DMA [ 1.750826] usbcore: registered new interface driver usbhid [ 1.756455] usbhid: USB HID core driver [ 1.761327] NET: Registered protocol family 26 [ 1.768044] TCP: cubic registered [ 1.771374] IPv6: Loaded, but administratively disabled, reboot required to enable [ 1.778999] sit: IPv6 over IPv4 tunneling driver [ 1.784131] NET: Registered protocol family 17 [ 1.790696] 8021q: 802.1Q VLAN Support v1.8 [ 1.799020] Key type dns_resolver registered VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 1.835858] ldo5: disabling [ 1.844634] ldo4: disabling [ 1.847847] regulator-dummy: disabling [ 1.851860] imx mcc test is registered. [ 1.856522] bd7181x-rtc bd7181x-rtc: setting system clock to 2001-01-06 22:56:39 UTC (978821799) [ 1.868902] ALSA device list: [ 1.873976] No soundcards found. [ 1.878598] Freeing unused kernel memory: 1444K (80718000 - 80881000) 3.10.53-lab126 #1 PREEMPT Sat Jun 4 12:16:28 PDT 2016 armv7l [ 2.095838] mmc0: BKOPS_EN bit is not set [ 2.118067] mmc0: new high speed DDR MMC card at address 0001 [ 2.124146] mmcblk0: mmc0:0001 NJ2ZMB 3.64 GiB [ 2.128775] mmcblk0boot0: mmc0:0001 NJ2ZMB partition 1 4.00 MiB [ 2.134818] mmcblk0boot1: mmc0:0001 NJ2ZMB partition 2 4.00 MiB [ 2.140822] mmcblk0rpmb: mmc0:0001 NJ2ZMB partition 3 512 KiB [ 2.147499] mmcblk0: p1 p2 p3 p4 [ 2.153624] mmcblk0boot1: unknown partition table [ 2.160443] mmcblk0boot0: unknown partition table [ 2.198419] INFO:child exited with status 00000000 [ 2.203876] INFO:find_file:118 Found V220_C283_BDB501_ED060SCSU1_TC.wrf.gz ERROR:wfm_count=1 [ 2.212861] mxc_epdc_eink: module license 'proprietary' taints kernel. [ 2.219567] Disabling lock debugging due to kernel taint [ 2.225282] INFO:Loaded module /lib/modules/mxc_epdc_eink.ko (11172 bytes) Panel VCOM string: 2690 [ 2.236440] imx_epdc_fb 20f4000.epdc: vcom_steps 125 [ 2.241652] imx_epdc_fb 20f4000.epdc: Memory override detected TotalMem:512M X:800 Y:600 FBMem:6M [ 2.257580] imx_epdc_fb 20f4000.epdc: EPDC version = 2.1.0 [ 2.324285] wv_file->wdh.luts & 0xC =4 [ 4.164649] INFO:Loaded module /lib/modules/mxc_epdc_fb.ko (79696 bytes) [ 4.448811] INFO:eink initialized... (486400 bytes) Press [ENTER] for recovery menu... 0 /[ 5.472702] INFO:!!! Checking MBR /dev/mmcblk0 !!!! [ 5.486678] INFO:partition 2, start sector is 987136 [ 5.491955] INFO:partition 3, start sector is 1118208 [ 5.497183] INFO:partition 4, start sector is 1249280 [ 5.502424] INFO:maximizing partition 6385664 sectors [ 5.507541] INFO:*** Partition table verified for /dev/mmcblk0 *** /dev/mmcblk0p4:[ 5.518422] INFO:Setup loop device /dev/loop0 for /dev/mmcblk0p4 + 8192 CHS=4/16/99776 size=3269459968 [ 5.528015] FAT-fs (loop0): Volume was not safely ejected. Run fsck to correct. bytes flag type first [ 5.536249] INFO:Checking for updates... (auto-pilot mode) last lba first lba size Part[ 5.544474] INFO:No update*.bin found; no update needed. ition p1: 0x00 0x0b 16 <[ 5.552925] INFO:no updates found. large> 16 6385648 CHS: 0/1/1 - <large> Partition p2: Partition p3: Partition p4: BOOTING DEFAULT. IP-Config: no devices to configure [ 6.383781] kjournald starting. Commit interval 5 seconds [ 6.389450] EXT3-fs (mmcblk0p1): using internal journal [ 6.394811] EXT3-fs (mmcblk0p1): mounted filesystem with ordered data mode kinit: Mounted root (ext3 filesystem). info sytem:mounted_proc:: info system:mounted_sys:: info system:sy00:: info firsttime:mount_rw:time=6880:Mounting root RW for first boot info firsttime:lostfound:Removing lost+found: info firsttime:usrlocal:Changing ownership for usr local: info firsttime:mtab:Linking /var/tmp: info firsttime:mtab:Linking Kindle Registry: info firsttime:xorgconf:Linking xorg.conf: info firsttime:cursor:Linking Xorg cursor: info firsttime:ssh:Generating rsa keys: info firsttime:mount_ro:time=8260:Mounting root RO info system:mounted_dev:: info milestone:8.32:49.1: info milestone:8.36:49.2: info milestone:8.38:49.3: info milestone:8.42:49.4: info milestone:8.45:49.5: info sytem:mounted_tmpfs:: info milestone:8.60:sy50: info system:start:time=8620: info hardware:no_wan::WiFi only device. No WAN found info system:config:platform=heisenberg,board=eanab,rev=17,proto=Y,wifi=Y,wan=N: [ 8.759781] udevd (298): /proc/298/oom_adj is deprecated, please use /proc/298/oom_score_adj instead. info milestone:8.78:sy51: lipc-send-event[407]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory) lipc-send-event[407]: C def:dbusi::Failed to init dbus lipc-send-event[407]: E def:open::Failed to open LIPC lipc-send-event[407]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed lipc-send-event[412]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory) lipc-send-event[412]: C def:dbusi::Failed to init dbus lipc-send-event[412]: E def:open::Failed to open LIPC lipc-send-event[412]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed info milestone:9.91:sy99: info system:done:time=9950: crond[427]: crond: crond (busybox 1.17.1) started, log level 8 init.exe: recevent pre-start process (430) terminated with st▒info system_cramfs_loopbacks:mountingcramfs:Mounting compressed directories filesystem images: warn system_cramfs_loopbacks:mountpointmissing:Image /lib/firmware/cyttsp.cramfs.img not mounted, non existing mounting point: info system_cramfs_loopbacks:mounted:Image /usr/share/X11/xkb.cramfs.img mounted: info system_cramfs_loopbacks:mounted:Image /usr/java/lib/fonts.cramfs.img mounted: info system_cramfs_loopbacks:mounted:Image /etc/kdb.src.cramfs.img mounted: info system_cramfs_loopbacks:mounted:Image /usr/lib/locale.cramfs.img mounted: info system_cramfs_loopbacks:mounted:Image /usr/share/keyboard.cramfs.img mounted: info system:emiting_event:mounted_cramfs_loopbacks: debug sytem:event_emitted:mounted_cramfs_loopbacks: info milestone:10.72:fs75: info system:emiting_event:loaded_modules_dependencies: debug sytem:event_emitted:loaded_modules_dependencies: info modules:modprobe:loading module fsl_otg_arc: crit modules:modprobe_failed:failed to load module fsl_otg_arc: info modules:modprobe:loading module ehci_hcd: crit modules:modprobe_failed:failed to load module ehci_hcd: info modules:modprobe:loading module fuse: [ 10.824945] fuse init (API version 7.22) info system:emiting_event:loaded_fuse: debug sytem:event_emitted:loaded_fuse: info hardware:no_wan::WiFi only device. No WAN found info milestone:10.86:fs00: info system:emiting_event:loaded_ppp_async: debug sytem:event_emitted:loaded_ppp_async: info system:emiting_event:loaded_fakekey: debug sytem:event_emitted:loaded_fakekey: [ 10.958831] kjournald starting. Commit interval 5 seconds [ 10.964943] EXT3-fs (mmcblk0p3): using internal journal [ 10.970764] EXT3-fs (mmcblk0p3): recovery complete [ 10.976339] EXT3-fs (mmcblk0p3): mounted filesystem with ordered data mode [ 10.991644] EXT3-fs (mmcblk0p1): using internal journal info filesystems_var_local:guid:Fetching existing guid: info milestone:11.06:fs23: info system:emiting_event:mounted_varLocal: debug sytem:event_emitted:mounted_varLocal: info milestone:11.12:fs25: info milestone:11.15:vi00: Welcome to Kindle! kindle login: [ 11.282955] Zforce2 regulator is not enabled! Enabling Zforce2 touch regulator... [ 11.329858] Zforce2 touch regulator is enabled! [ 11.395478] EXT3-fs (mmcblk0p1): using internal journal [ 11.537512] FAT-fs (loop1): Volume was not safely ejected. Run fsck to correct. [ 11.645942] input: zforce2 as /devices/platform/zforce2.0/input/input0 info milestone:11.84:vi99: info display:started:time=11890: info system:emiting_event:display_ready: debug sytem:event_emitted:display_ready: info system:emiting_event:loaded_touch: debug sytem:event_emitted:loaded_touch: info userstore:run:time=12270,action=start: info userstore:start:found_bootup_flag:Found BOOTUP flag file info prereg:PRAGMA_QUICK_CHECK_PASSED::sts=0 info mntus:fs_error_recover::File system errors recovered [ 14.222494] g_mass_storage gadget: Mass Storage Function, version: 2009/09/11 [ 14.229644] g_mass_storage gadget: Number of LUNs=1 [ 14.247921] lun0: LUN: removable file: (no medium) [ 14.254909] fsg_bind:3212 [ 14.257557] g_mass_storage gadget: Internal Storage, version: 2009/09/11 [ 14.276514] g_mass_storage gadget: userspace failed to provide iSerialNumber [ 14.289602] g_mass_storage gadget: g_mass_storage ready info system:emiting_event:mounted_userstore: debug sytem:event_emitted:mounted_userstore: info milestone:14.40:fs50: info milestone:14.46:fs90: info milestone:14.53:fs99: info battery:charged:cap=,mV=,mAH=: [ 14.598626] usb_gadget_state_work: gadget state: addresssed info system:emiting_event:battery_ready: [ 14.643647] g_mass_storage gadget: high-speed config #1: Linux File-Backed Storage [ 14.651262] usb_gadget_state_work: gadget state: configured [ 14.657414] send_online_uevent:432 fsg_ 0x0 recovery_mode:0 debug sytem:event_emitted:battery_ready: info milestone:14.69:sys99: info system:emiting_event:devcap_ready: debug sytem:event_emitted:devcap_ready: info system:emiting_event:dbus_ready: debug sytem:event_emitted:dbus_ready: info dbus:check-update:status=2:dbus_ready sent info hardware:no_wan::WiFi only device. No WAN found info milestone:16.08:xx00: info X:load:time=16200: info X:xorg.conf:Generating xorg.conf: info X:xorg.conf:xorg.conf generated: info milestone:17.77:xx50: info X:starting:time=17830: info milestone:21.60:xx99: info X:started:time=21640: info system:emiting_event:x_setup_ready: debug sytem:event_emitted:x_setup_ready: info asr_setup:winmgr_running=true. winmgr is ready:: info locale:read:lang=de_DE.utf8,lc_all=de_DE.utf8:Retrieved Language info system:emiting_event:langpicker_ready: debug sytem:event_emitted:langpicker_ready: info blanket_f:module already loaded:splash: info milestone:23.73:pi00: info milestone:24.02:pi99: info system:emiting_event:contentpack_font_ready: debug sytem:event_emitted:contentpack_font_ready: info milestone:25.61:fr00: info milestone:25.73:fr50: info milestone:25.74:fr51: info framework:starting:time=26900: info hardware:no_wan::WiFi only device. No WAN found [ 30.359974] dhd_module_init in [ 30.363673] dhd_module_init fw_image_unaligned=9a500000 fw_image=9a500000 [ 30.374682] brcm_wlan_power: setting gpio #[47] on [ 30.541632] found wifi platform device bcmdhd_wlan [ 30.553191] dhd_module_init out [ 30.881706] mmc1: new high speed SDIO card at address 0001 [ 30.906311] alloc static buf at 9a440000! [ 30.925345] DHD: dongle ram size is set to 524288(orig 524288) at 0x0 [ 30.934026] wifi_platform_get_mac_addr CFG80211-ERROR) wl_event_handler : [ 30.949888] dhd_deferred_work_init: work queue initialized tsk Enter, tsk = 0x9a23f5dc [ 30.966130] dhdsdio_download_code_file: download firmware '/opt/brcm_4343w/wifi/firmware/fw_bcmdhd_sr.bin' and save a copy to 9a500000 [ 31.052963] dhdsdio_download_code_file finished f/w download fw_image_size=351012 [ 31.068294] dhdsdio_download_nvram: MAX=4096 len=906 read [ 31.076305] dhdsdio_download_nvram: MAX=4096 len=906 saved [ 31.146009] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us) [ 31.161595] wifi_platform_get_mac_addr [ 31.172778] dhd_wlfc_init(): successfully enabled bdcv2 tlv signaling, 79 [ 31.180464] dhd_wlfc_init: query wlfc_mode succeed, fw_caps=0x1c [ 31.189827] dhd_wlfc_init(): wlfc_mode=0x1c, ret=0 [ 31.196191] Dongle Host Driver, version 1.201.59 (r506368) Compiled from [ 31.210833] Register interface [wlan0] MAC: 00:be:6e info milestone:61.53:fr99: info framework:started:time=61560,delta=35830: info blanket_f:loading blanket module:usb: info blanket_f:unloading blanket module:splash: info system:emiting_event:framework_ready: debug sytem:event_emitted:framework_ready: info stored:started:: info stored:read_in_counters:REBOOTS=0, REBOOT_LIMIT=1, RESTARTS=0, RESTART_LIMIT=5: [ 63.161576] EXT3-fs (mmcblk0p1): using internal journal info monitor:writing_file:file=/var/run/upstart/stored.restarts: Retrieved 344 keys for system/daemon/pmond/ [ 71.039917] fsg_suspend:3275 [ 71.042887] usb_gadget_state_work: gadget state: suspended [ 71.348453] fsg_disable:2563 [ 71.351413] send_offline_uevent:407 fsg_ 0xa unsafe 1 recovery_mode:0 [ 71.380822] send_offline_uevent:407 fsg_ 0x0 unsafe 0 recovery_mode:0 info asr_setup:winmgr_running=true. winmgr is ready:: [ 73.874506] usb_gadget_state_work: gadget state: not attached [ 814.901735] usb_gadget_state_work: gadget state: powered [ 815.197328] usb_gadget_state_work: gadget state: addresssed [ 815.242808] g_mass_storage gadget: high-speed config #1: Linux File-Backed Storage [ 815.250488] send_online_uevent:432 fsg_ 0x0 recovery_mode:0 [ 815.258059] usb_gadget_state_work: gadget state: configured info stored:post-stop script - Time Interval = 752:: info stored:post-stop script - cleared counters:: info stored:post-stop script - sending event to appmgrd:: info stored:started:: info stored:read_in_counters:REBOOTS=0, REBOOT_LIMIT=1, RESTARTS=0, RESTART_LIMIT=5: info monitor:writing_file:file=/var/run/upstart/stored.restarts: [ 835.345080] fsg_disable:2563 [ 835.348014] g_mass_storage gadget: high-speed config #0: unconfigured [ 835.354594] send_offline_uevent:407 fsg_ 0x2 unsafe 0 recovery_mode:0 [ 835.379353] usb_gadget_state_work: gadget state: suspended info asr_setup:winmgr_running=true. winmgr is ready:: [ 935.144690] usb_gadget_state_work: gadget state: not attached Last edited by Bergfux; 07-10-2018 at 01:02 AM. |
07-15-2018, 11:38 PM | #393 |
Junior Member
Posts: 8
Karma: 10
Join Date: Jan 2014
Device: none
|
Maybe this goes without saying, but I think the HOWTO would be improved if it specified soldering hair-thin wires onto the comm pads.
I used 22-ga solid, figuring I'd plug a standard female header cable on it, and just insulate and leave it in place when I buttoned back up. Go ahead and judge; the method's worked well for me in the past, albeit perhaps on beefier pads. In any case, this time I twitched, and tore off the entire tx pad. I assume this is the end of the experiment for *this* particular PW3, unless someone can tell me another place to access that trace? |
07-16-2018, 08:59 AM | #394 | |
Guru
Posts: 645
Karma: 1888888
Join Date: Jun 2009
Device: prs-505, Kindle Keyboard 3g, PW3
|
Quote:
But you cannot really leave those hooked up, so you will have to clean the sodler off before you re-assemble the kindle, but you can jailbreak with it semi disassembled. Heres my pic of that. https://www.mobileread.com/forums/sh...2&postcount=40 You do have to have the screen connected for the kindle to poot, but you can use electracal tape and set everything back in place loosely, to do this part. but the solder is too thick to let you screw everything back together properly. Last edited by coplate; 07-16-2018 at 09:11 AM. |
|
07-16-2018, 10:33 AM | #395 |
Going Viral
Posts: 17,212
Karma: 18210809
Join Date: Feb 2012
Location: Central Texas
Device: No K1, PW2, KV, KOA
|
@dsjstc: Which is why in the various write-ups I have done here, I show in an early step an expample of using a drop of "5-Minute" epoxy on the leads as a strain relief. Before doing the lead alignment and the soldering.
Notice in this thread there are also links to ways to make the connections without using hot solder. I am sure you are not the first one to be tripped up by over confidence. That "na, I don't need to do that" feeling. And yes, that serial pin out is for a "standard" three lead connector. (Some of the early K4 devices actually shipped with the connector in-place.) I have a thread/post with pictures on this forum somewhere about the connectors. Last edited by knc1; 07-16-2018 at 10:38 AM. |
08-23-2018, 06:32 PM | #396 |
Junior Member
Posts: 5
Karma: 10
Join Date: Aug 2018
Device: Kindle Paperwhite 3
|
Just wanted to share a serial connector that worked for me on a Kindle Paperwhite 3. The connector is similar to what others have used and consists in two cheap modules bought on ebay:
- FT232RL-FTDI-USB-3-3V-5-5V-to-TTL-Serial-Adapter-Module-for-Arduino-Mini-Port - 12V In 1.8V Out AMS1117 Step-Down DC Power Converter Module In addition, the following is very handy: - STOCK IN US 1pc 40P 20cm 2.54mm Female to Female Dupont Wire Color Jumper Cable - 3 Needles (like the ones coming with new shirts) To assemble, cut one of the female to female jumper cable in half and solder one of them to the 5V pinout of the FTDI and the other to the GND. Connect the two jumpers to the 5V input of the Step-Down module. Connect a Female to Female Jumper cable from the 1.8V output of the step-down module to the middle jumper of the FTDI. This provides the 1.8 Voltage to the FTDI, instead of the 3.3V or 5.5V that can be selected using the original jumper. The FTDI can then be connected to the serial pins of the Kindle. I elected not to solder the wires and used instead 3 needles that I cut and inserted into the jumper cable (fits perfectly). I used foam as described in another thread to hold the needle in place. See pictures for more help. The whole thing worked perfectly to rescue a bricked PW3 for less then $10. |
08-27-2018, 09:43 AM | #397 |
Junior Member
Posts: 4
Karma: 10
Join Date: Aug 2018
Device: KT3
|
Hello I have a KT3W (White) Kindle with Serial G000KA and i can't interrupt the boot sequence. What can i do?
|
08-28-2018, 02:47 AM | #398 | |
Junior Member
Posts: 5
Karma: 10
Join Date: Jun 2018
Device: Paperwhite 3
|
Quote:
I've just successfully jailbreaked (jailbroken?) a PW3 (G090 G105) running FW v5.9.6.1 using serial method. That was an adventure! Now I'm ready to install KUAL and other fun stuffs, but not sure what to do with the G090G1.bin file... Care to expand on your advice above? Or point me to more info somewhere? Thanks! |
|
08-30-2018, 09:16 AM | #399 |
BLAM!
Posts: 13,477
Karma: 26012494
Join Date: Jun 2010
Location: Paris, France
Device: Kindle 2i, 3g, 4, 5w, PW, PW2, PW5; Kobo H2O, Forma, Elipsa, Sage, C2E
|
@RedRooster: That was a WIP build, forget about it and go read KUAL's first post and the relevant FAQ entry.
|
10-20-2018, 09:18 AM | #400 |
Member
Posts: 17
Karma: 470352
Join Date: Dec 2012
Location: Various
Device: Kindle keyboard, Kindle Paper White, Android app
|
alternative serial adapter
The recommended adapter on the original post has been unavailable for some time. I would like to stick to the instructions as has been repeatedly reinforced on this site, but I was wondering if I could use the new Micro1v8.
Thank you for the clear guide. |
10-20-2018, 10:10 AM | #401 |
Going Viral
Posts: 17,212
Karma: 18210809
Join Date: Feb 2012
Location: Central Texas
Device: No K1, PW2, KV, KOA
|
|
10-23-2018, 12:42 PM | #402 |
Junior Member
Posts: 1
Karma: 10
Join Date: Oct 2018
Device: Kindle Voyage & PW4
|
1.8v USB to TTL UART Converter
I ordered this from ebay yesterday. Listing # "142006114032" TXD 1.8v PL2303 USB to TTL UART Converter Serial Download Cable module. Its coming on a slow boat from you know where. It needs 5 volts for vcc. If I can't find 5v on the mother board, I can grab it from somewhere. Also, the same store lists quantity 5 for $10.48 USD, free shipping.
|
10-23-2018, 01:23 PM | #403 |
Junior Member
Posts: 3
Karma: 10
Join Date: Oct 2018
Device: Kindle Voyage
|
Hello! So I followed your guide with my Kindle Voyage,using the items you had outlined I was able to get root access, place the files and then run the jail break (i even got the jailbreak message on the screen)
But for the life of me i cannot get KUAL working. I am trying to ;log mrpi method and the screen simply flashes and nothing happens. I am on firmware 5.9.7 on the Kindle Voyage. I'm posting the putty code following my root below. I appreciate the help guys I've now attempted to re-jailbreak twice and the same thing keeps happening. I'm using all files from the "snapshot" thread. Thank you so much as I'm going a bit crazy here haha! Code:
kindle login: root ################################################# # N O T I C E * N O T I C E * N O T I C E # ################################################# Rootfs is mounted read-only. Invoke mntroot rw to switch back to a writable rootfs. ################################################# [root@kindle root]# cd /mnt/us [root@kindle us]# sh jb.sh info jb_install:mount_root_rw::Mounting rootfs rw info jb_install:install_update_key::Copying the jailbreak updater key info jb_install:install_fw54_exec_userstore_flag::Creating the userstore exec flag file info jb_install:install_bridge::Installing the jailbreak bridge info jb_install:install::Setting up MKK persistent copy info jb_install:install::Setting up RP persistent copy update_to_display: update_mode=PARTIAL, wave_mode=257 inverted=0 [root@kindle us]# reboot reboot: command arguments: no_sync=0, force=0, poweroff=0, exit_only=0, args=77120 [root@kindle us]# Broadcast message from root@kindle (/dev/ttymxc0) at 13:06 ... The system is going down for reboot NOW! info shutdown:begin:level=6,halt=,special=: info shutdown:closing password dialog:: info blanket_f:loading blanket module:shutdown: info shutdown_showimage:screen:splashing screen:reboot info shutdown_showimage:screen:waiting for reboot screen to come up: info upstart_f:stopping_job:job=x: info stored:post-stop script - Time Interval = 180:: info upstart_f:stopping_job:job=wifid: info stored:post-stop script - cleared counters:: info stored:post-stop script - sending event to appmgrd:: info upstart_f:job_already_stopped:job=wifis: info upstart_f:stopping_job:job=lab126: info upstart_f:jobs_stopped:elapsed_ms=5290,timeout_ms=45000: info upstart_f:stopping_job:job=filesystems: info filesystems_var_local:unmounting font files:: info filesystems_userstore:unmount_userstore:Unmounting UserStore: info filesystems_var_local:rotate_log:Rotating Logs: info userstore:run:time=303180,action=stop: info userstore:filesystem sync done:: info userstore:stop:found_bootup_flag:Found BOOTUP flag file info filesystems_var_local:filesystem sync done:: info filesystems_var_local:unmount_varLocal:Unmounting VarLocal: info upstart_f:jobs_stopped:elapsed_ms=4430,timeout_ms=30000: info shutdown:mounting root filesystem read-only:: info shutdown:syncing disks:: info shutdown:end:level=6,halt=: [ 307.691339] imx2-wdt imx2-wdt.0: Device shutdown: Expect reboot! [ 307.697395] Restarting system. HW U-Boot 2009.08-lab126 (Jul 24 2018 - 06:38:29) CPU: Freescale i.MX6 family TO0.0 at 996 MHz Temperature: 33 C, calibration data 0x56c4f15f mx6sl pll1: 996MHz mx6sl pll2: 528MHz mx6sl pll3: 480MHz mx6sl pll8: 50MHz ipg clock : 66000000Hz ipg per clock : 24000000Hz uart clock : 80000000Hz cspi clock : 60000000Hz ahb clock : 132000000Hz axi clock : 198000000Hz emi_slow clock: 22000000Hz ddr clock : 396000000Hz usdhc1 clock : 198000000Hz usdhc2 clock : 198000000Hz usdhc3 clock : 198000000Hz usdhc4 clock : 198000000Hz MMC: FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2 Board: Icewine WFO 512 Boot Reason: [ POR ] Boot Device: NAND Board Id: 048090C1704202YC S/N: 90130907706400TT I2C: ready DRAM: 512 MB Using default environment In: serial Out: serial Err: serial Quick Memory Test 0x80000000, 0x1fff0000 POST done in 112 ms Battery voltage: 4296 mV check_haptic: ID = 0x07 Hit any key to stop autoboot: 0 ## Booting kernel from Legacy Image at 80800000 ... Image Name: Linux-3.0.35-lab126 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2952672 Bytes = 2.8 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.096537] [ 0.270914] LPDDR2 MfgId: 0x3 [Elpida] [ 0.274688] [ 0.274691] just text: vaddr c0131fdc, va 0xc0131200 pa 0x801000c3 attr 0x6 [ 0.287270] [ 0.287273] nmx6sl_wfi_iram: vaddr e084e000, va 0xe084e200 pa 0x904043 attr 0x2 [ 0.296117] [ 0.296120] mx6sl_ddr: vaddr e0856000, va 0xe0856200 pa 0x905043 attr 0x2 [ 0.304450] [ 0.304453] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149 [ 0.315284] [ 0.315286] ANATOP: vaddr f40c8000, va 0xf40c8200 pa 0x20110c3 attr 0x149 [ 0.329633] [ 0.329635] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149 [ 0.341773] [ 0.341776] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149 [ 0.352142] [ 0.352144] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149 [ 0.362031] [ 0.362034] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149 DEBUG:recovery-util.c:1680:setup_die_signals():Installed signal handlers. 3.0.35-lab126 #2 PREEMPT Tue Jul 24 06:43:56 PDT 2018 armv7l Press [ENTER] for recovery menu... 0 /BOOTING DEFAULT. IP-Config: no devices to configure kinit: Mounted root (ext3 filesystem) readonly. info sytem:mounted_proc:: info system:mounted_sys:: info system:sy00:: info system:mounted_dev:: info milestone:6.99:49.1: info milestone:7.02:49.2: info milestone:7.05:49.3: info milestone:7.11:49.4: info milestone:7.15:49.5: info sytem:mounted_tmpfs:: info milestone:7.22:sy50: info system:start:time=7250: info hardware:no_wan::WiFi only device. No WAN found info system:config:platform=wario,board=icewine,rev=9,proto=Y,wifi=Y,wan=N: info milestone:7.46:sy51: lipc-send-event[841]: W def:lipc:method=LipcOpenEx service=com.lab126.hal:Method has been deprecated. lipc-send-event[840]: W def:lipc:method=LipcOpenEx service=com.lab126.hal:Method has been deprecated. lipc-send-event[840]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory) lipc-send-event[840]: C def:dbusi::Failed to init dbus lipc-send-event[840]: E def:open::Failed to open LIPC lipc-send-event[840]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed lipc-send-event[841]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory) lipc-send-event[841]: C def:dbusi::Failed to init dbus lipc-send-event[841]: E def:open::Failed to open LIPC lipc-send-event[841]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed info milestone:8.32:sy99: info system:done:time=8360: crond[853]: crond: crond (busybox 1.17.1) started, log level 8 init.exe: sshd main ▒rocess (852)init.exe: sshd main process ended, respawning init.exe: recevent pre-start process (856) terminated with status 1 info milestone:8.68:sc01: info system_fs_loopbacks:mountingfs:Mounting compressed directories filesystem images: info milestone:8.70:sc02: info milestone:8.75:/usr/share/X11/xkb: info system_fs_loopbacks:mounted:Image /usr/share/X11/xkb.sqsh mounted: info milestone:8.79:3: info milestone:8.80:sc05: info milestone:8.81:/usr/java/lib/fonts: info system_fs_loopbacks:mounted:Image /usr/java/lib/fonts.sqsh mounted: info milestone:8.85:4: info milestone:8.86:sc05: info milestone:8.87:/etc/kdb.src: info system_fs_loopbacks:mounted:Image /etc/kdb.src.sqsh mounted: info milestone:8.91:5: info milestone:8.91:sc05: info milestone:8.93:/usr/lib/locale: info system_fs_loopbacks:mounted:Image /usr/lib/locale.sqsh mounted: info milestone:8.96:6: info milestone:8.97:sc05: info milestone:8.98:/usr/share/keyboard: info system_fs_loopbacks:mounted:Image /usr/share/keyboard.sqsh mounted: info milestone:9.08:7: info milestone:9.09:sc05: info milestone:9.10:/opt/var/local: info system_fs_loopbacks:mounted:Image /opt/var/local.sqsh mounted: info milestone:9.14:8: info milestone:9.15:sc05: info milestone:9.16:sc07: info system:emiting_event:mounted_fs_loopbacks: debug sytem:event_emitted:mounted_fs_loopbacks: info milestone:9.20:fs75: info system:emiting_event:loaded_modules_dependencies: debug sytem:event_emitted:loaded_modules_dependencies: info modules:modprobe:loading module fsl_otg_arc: info system:emiting_event:loaded_fsl_otg_arc: debug sytem:event_emitted:loaded_fsl_otg_arc: info modules:modprobe:loading module ehci_hcd: info system:emiting_event:loaded_ehci_hcd: debug sytem:event_emitted:loaded_ehci_hcd: info modules:modprobe:loading module fuse: info system:emiting_event:loaded_fuse: debug sytem:event_emitted:loaded_fuse: info hardware:no_wan::WiFi only device. No WAN found info system:emiting_event:loaded_ppp_async: info milestone:9.48:fs00: debug sytem:event_emitted:loaded_ppp_async: info filesystem_keys:not applicable for this device type:: info modules:modprobe:loading module als_max44009: Welcome to Kindle! kindle login: info system:emiting_event:loaded_als_max44009: debug sytem:event_emitted:loaded_als_max44009: info system:emiting_event:loaded_fakekey: debug sytem:event_emitted:loaded_fakekey: info filesystems_var_local:runfixup:Running /var/local/system/fixup: info jb_bridge:install_mkk_dev_keystore::Copying the kindlet keystore info filesystems_var_local:DB PARAMS:FreePageSize:1024 bytes. AvailableSpaceInVarLocal:42881 KB.: info milestone:10.20:fs23: info system:emiting_event:mounted_varLocal: debug sytem:event_emitted:mounted_varLocal: info milestone:10.25:fs25: info milestone:10.28:vi00: info prereg:PRAGMA_QUICK_CHECK_PASSED::sts=0 info userstore:run:time=10620,action=start: info userstore:start:found_shutdown_flag:Found SHUTDOWN flag file info display:update:Checking '/opt/eink/images/G152_ED060TC1C1' for overrides: info system:emiting_event:mounted_userstore: debug sytem:event_emitted:mounted_userstore: info milestone:11.76:fs50: info milestone:11.79:fs90: info milestone:11.84:fs99: [ 12.700360] [DRV26XX]Found matching id! [ 12.712178] [DRV26XX]Probe succeeded! info milestone:12.70:vi99: info display:started:time=12730: info system:emiting_event:display_ready: debug sytem:event_emitted:display_ready: [ 12.922378] fsr_config: n_adc=6, adc_depth=16, app_ver=10, n_buttons=4, flash=8000 info battery:charged:cap=100,mV=4279,mAH=1294: info system:emiting_event:battery_ready: debug sytem:event_emitted:battery_ready: info fsr_keypad:adc: 726 550 1276 680, 0 0: info fsr_keypad:calibration: 4 3 1 0 250 500 0 0 0 0 0 629 1155 1779 48879 48879 48879 48879 48879 525 1747 2209 48879 48879 48879 48879 48879 1046 1512 1890 48879 48879 48879 48879 48879 724 1720 2189 48879 48879 48879 48879 48879 : info fsr_keypad:update:fsr app version=0x0010: info system:emiting_event:loaded_touch: debug sytem:event_emitted:loaded_touch: info milestone:13.28:sys99: info system_setup:system_setup_after_shpm done:: info system:emiting_event:dbus_ready: debug sytem:event_emitted:dbus_ready: info dbus:check-update:status=2:dbus_ready sent info hardware:no_wan::WiFi only device. No WAN found info milestone:14.30:dy01: info milestone:14.98:xx00: info X:load:time=15090: info X:xorg.conf:Generating xorg.conf: [ 15.491100] pmic_soda_connects_notify_otg_out:423 info X:xorg.conf:xorg.conf generated: info milestone:17.28:xx50: info X:starting:time=17320: info milestone:20.23:xx99: info X:started:time=20260: info system:emiting_event:x_setup_ready: debug sytem:event_emitted:x_setup_ready: info asr_setup:Not in asr mode::reason=flag file not present. shutting down asr_setup:: info locale:read:lang=en_US.utf8,lc_all=en_US.utf8:Retrieved Language info system:emiting_event:langpicker_ready: debug sytem:event_emitted:langpicker_ready: info blanket_f:module already loaded:splash: info asr_bt_reboot:asr_bt_reboot begin on started winmgr_ready:: info milestone:22.13:pi00: info milestone:22.39:pi99: info system:emiting_event:contentpack_font_ready: debug sytem:event_emitted:contentpack_font_ready: info milestone:24.87:fr00: info milestone:24.98:fr50: info milestone:25.01:fr51: info framework:starting:time=26810: info framework:commandLine:HEAP = -minimal -Xmx30m -XX:MaxNewSize=4m -XX:SurvivorRatio=2 -XX:TargetSurvivorRatio=80 -Xss100k -XX:ReservedCodeCacheSize=3m -XX:CompileThreshold=5000 -XX:CodeCacheMinimumFreeSpace=100k -XX:NmethodSweepFraction=6 -XX:NmethodSweepActivity=2 -XX:NmethodSweepMaxWaitTime=8 -XX:NmethodHotnessCounterResetValue=64 -XX:MinHeapFreeRatio=5 -XX:MaxHeapFreeRatio=15 -XX:+UseAggressiveHeapShrink -XX:MaxInlineSize=16 -XX:MaxInlineLevel=2 -XX:-InlineSynchronizedMethods: info hardware:no_wan::WiFi only device. No WAN found info framework:##### Starting Java SE8 VM :: info milestone:59.24:fr99: info framework:started:time=59360,delta=34360: info blanket_f:loading blanket module:usb: info blanket_f:unloading blanket module:splash: info system:emiting_event:framework_ready: debug sytem:event_emitted:framework_ready: info stored:started:: info stored:read_in_counters:REBOOTS=0, REBOOT_LIMIT=1, RESTARTS=0, RESTART_LIMIT=5: info monitor:writing_file:file=/var/run/upstart/stored.restarts: info clickstreamHeartbeatMetricsFramework:Skipping metrics recording, as it is the same day:: Retrieved 356 keys for system/daemon/pmond/ |
10-23-2018, 01:59 PM | #404 |
BLAM!
Posts: 13,477
Karma: 26012494
Join Date: Jun 2010
Location: Paris, France
Device: Kindle 2i, 3g, 4, 5w, PW, PW2, PW5; Kobo H2O, Forma, Elipsa, Sage, C2E
|
@ldb2742: Install the latest JB Hotfix package via UYK, the old standalone JB did not bundle the dispatch script needed for the ;log functionality (IIRC).
|
10-23-2018, 02:57 PM | #405 | |
Junior Member
Posts: 3
Karma: 10
Join Date: Oct 2018
Device: Kindle Voyage
|
Quote:
So is there a way to buy you a beer over the internet? This worked perfectly. The instructions were spot on, but the original post should probably just have a quick update that the final step is to flash the hotfix via UYK. You guys rock! |
|
Tags |
serial jailbreak |
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
How much would people pay for easy serial jailbreaking their paperwhite? | coplate | Kindle Developer's Corner | 3 | 02-21-2018 12:45 PM |
Serial Jailbreaking FW >= 5.6.1.1 | knc1 | Kindle Developer's Corner | 6 | 08-14-2017 08:38 AM |
Need help jailbreaking this kindle that i have | wizo | Kindle Developer's Corner | 5 | 11-15-2012 07:50 AM |
Free (Kindle) A Little Bit of Everything For Dummies | arcadata | Deals and Resources (No Self-Promotion or Affiliate Links) | 1 | 11-23-2011 10:51 AM |
Which Kindle do I need for jailbreaking? | chas0039 | Kindle Developer's Corner | 6 | 11-10-2010 10:04 PM |