01-25-2016, 02:45 AM
|
#1 |
|
Member
 Posts: 21
Karma: 10
Join Date: Mar 2015
Device: PW, PW2, KV
|
Kindle Voyage display problem
Hello All!
I've a Kindle Voyage which looks normal for the first time: - It boots (shows the child under the tree, loading completes) - But here comes the interesting part: After the loading completes the screen shows the screensaver image. I can't wake it up with the power button  What i've done so far: - Extracted the 5.6.5 update and flashed uImage to kernel - Formatted FAT - Exported as USB - Then copied the full update file to the device and it updated. But the situation is the same... I've went into diags and the touch working, the lights working so it looks like the screen is OK to me. Here is a boot log: Code:
U-Boot 2009.08-lab126 (Dec 10 2014 - 13:25:46)
CPU: Freescale i.MX6 family TO0.0 at 996 MHz
Temperature: 35 C, calibration data 0x5775015f
mx6sl pll1: 996MHz
mx6sl pll2: 528MHz
mx6sl pll3: 480MHz
mx6sl pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 66000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 198000000Hz
emi_slow clock: 22000000Hz
ddr clock : 396000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
MMC: FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2
Board: Icewine WFO 512
Boot Reason: [ POR ]
Boot Device: NAND
Board Id: xxxxxxxxxxxxxxxx
S/N: xxxxxxxxxxxxxxxx
I2C: ready
DRAM: 512 MB
Using default environment
In: serial
Out: serial
Err: serial
Quick Memory Test 0x80000000, 0x1fff0000
POST done in 116 ms
Battery voltage: 4255 mV
check_haptic: ID = 0x07
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at 80800000 ...
Image Name: Linux-3.0.35-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2633728 Bytes = 2.5 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.098507] No Legacy reboot reason code to print
[ 0.287860] LPDDR2 MfgId: 0x1 [Samsung]
[ 0.291723]
[ 0.291726] just text: vaddr c0150d44, va 0xc0150200 pa 0x801000c3 attr 0x6
[ 0.304183]
[ 0.304187] nmx6sl_wfi_iram: vaddr e084e000, va 0xe084e200 pa 0x904043 attr 0x2
[ 0.313057]
[ 0.313060] mx6sl_ddr: vaddr e0856000, va 0xe0856200 pa 0x905043 attr 0x2
[ 0.321477]
[ 0.321480] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149
[ 0.332251]
[ 0.332254] ANATOP: vaddr f40c8000, va 0xf40c8200 pa 0x20110c3 attr 0x149
[ 0.345581]
[ 0.345584] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149
[ 0.355615]
[ 0.355618] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149
[ 0.368027]
[ 0.368030] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149
[ 0.377963]
[ 0.377966] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149
3.0.35-lab126 #1 PREEMPT Fri Jul 31 15:04:21 PDT 2015 armv7l
Press [ENTER] for recovery menu... 0 //dev/mmcblk0p4:
CHS=4/16/101312 size=3319791616 bytes
flag type first last lba first lba size
Partition p1:
0x00 0x0b 16 <large> 16 6483952
CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
BOOTING DEFAULT.
IP-Config: no devices to configure
kinit: Mounted root (ext3 filesystem) readonly.
info sytem:mounted_proc::
info system:mounted_sys::
info system:mounted_dev::
info milestone:6.92:49.1:
info milestone:6.96:49.2:
info milestone:6.99:49.3:
info milestone:7.03:49.4:
info milestone:7.06:49.5:
info sytem:mounted_tmpfs::
info milestone:7.12:sy50:
info system:start:time=7150:
info hardware:no_wan::WiFi only device. No WAN found
info system:config:platform=wario,board=icewine,rev=9,proto=Y,wifi=Y,wan=N:
info milestone:7.35:sy51:
lipc-send-event[793]: E lipc:con::Connection error(Failed to connect to socket /
lipc-send-event[793]: C def:dbusi::Failed to init dbus
lipc-send-event[793]: E def:open::Failed to open LIPC
lipc-send-event[793]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending
lipc-send-event[792]: E lipc:con::Connection error(Failed to connect to socket /
lipc-send-event[792]: C def:dbusi::Failed to init dbus
lipc-send-event[792]: E def:open::Failed to open LIPC
lipc-send-event[792]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending
info milestone:8.24:sy99:
info system:done:time=8270:
crond[824]: crond: crond (busybox 1.17.1) started, log level 8
init.exe: sshd main process (822) terminated with ótatus 2
init.exe: sshd main process ended, respawning
init.exe: recevent pre-start process (827) terminated ÷ith statusinfo system_cramfs_loopbacks:mountingcramfs:Mounting compressed directories filesystem images:
warn system_cramfs_loopbacks:mountpointmissing:Image /lib/firmware/cyttsp.cramfs.img not mounted, non existing mounting point:
info system_cramfs_loopbacks:mounted:Image /usr/share/X11/xkb.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/java/lib/fonts.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /etc/kdb.src.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/lib/locale.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/share/keyboard.cramfs.img mounted:
info system:emiting_event:mounted_cramfs_loopbacks:
debug sytem:event_emitted:mounted_cramfs_loopbacks:
info milestone:8.92:fs75:
info system:emiting_event:loaded_modules_dependencies:
debug sytem:event_emitted:loaded_modules_dependencies:
info modules:modprobe:loading module g_file_storage:
info system:emiting_event:loaded_g_file_storage:
debug sytem:event_emitted:loaded_g_file_storage:
info modules:modprobe:loading module fuse:
info system:emiting_event:loaded_fuse:
debug sytem:event_emitted:loaded_fuse:
info hardware:no_wan::WiFi only device. No WAN found
info system:emiting_event:loaded_ppp_async:
info milestone:9.15:fs00:
debug sytem:event_emitted:loaded_ppp_async:
info modules:modprobe:loading module als_max44009:
info system:emiting_event:loaded_als_max44009:
debug sytem:event_emitted:loaded_als_max44009:
info system:emiting_event:loaded_fakekey:
debug sytem:event_emitted:loaded_fakekey:
Welcome to Kindle!
kindle login: info milestone:9.58:fs23:
info system:emiting_event:mounted_varLocal:
debug sytem:event_emitted:mounted_varLocal:
info milestone:9.65:fs25:
info milestone:9.68:vi00:
info prereg:PRAGMA_QUICK_CHECK_PASSED::sts=0
info display:update:Checking '/opt/eink/images/G130_ED060TC1C1' for overrides:
info milestone:11.85:vi99:
info display:started:time=11880:
info system:emiting_event:display_ready:
debug sytem:event_emitted:display_ready:
[ 12.036022] [DRV26XX]Found matching id!
[ 12.044917] [DRV26XX]Probe succeeded!
info userstore:run:time=12140,action=start:
info userstore:start:found_bootup_flag:Found BOOTUP flag file
info battery:charged:cap=100,mV=4241,mAH=1254:
info system:emiting_event:battery_ready:
debug sytem:event_emitted:battery_ready:
[ 12.258694] fsr_config: n_adc=6, adc_depth=16, app_ver=10, n_buttons=4, flash=8000
info fsr_keypad:adc:1528 1908 1240 1630, 0 0:
info fsr_keypad:calibration:
4 3 1
0 250 500 0 0 0 0 0
1320 1577 1856 48879
48879 48879 48879 48879
1727 2122 2329 48879
48879 48879 48879 48879
411 804 1342 48879
48879 48879 48879 48879
2091 2270 2422 48879
48879 48879 48879 48879 :
info fsr_keypad:update:fsr app version=0x0010:
info system:emiting_event:loaded_touch:
debug sytem:event_emitted:loaded_touch:
info system:emiting_event:mounted_userstore:
debug sytem:event_emitted:mounted_userstore:
info milestone:13.05:fs50:
info milestone:13.07:fs90:
info milestone:13.09:fs99:
info milestone:13.11:sys99:
info system:emiting_event:devcap_ready:
debug sytem:event_emitted:devcap_ready:
info system:emiting_event:dbus_ready:
debug sytem:event_emitted:dbus_ready:
info dbus:check-update:status=2:dbus_ready sent
info hardware:no_wan::WiFi only device. No WAN found
info milestone:14.35:xx00:
info X:load:time=14430:
info X:xorg.conf:Generating xorg.conf:
info X:xorg.conf:xorg.conf generated:
info milestone:15.95:xx50:
info X:starting:time=15990:
info milestone:18.63:xx99:
info X:started:time=18660:
info system:emiting_event:x_setup_ready:
debug sytem:event_emitted:x_setup_ready:
info asr_setup:winmgr_running=true. winmgr is ready::
info locale:read:lang=en_GB.utf8,lc_all=en_GB.utf8:Retrieved Language
info system:emiting_event:langpicker_ready:
debug sytem:event_emitted:langpicker_ready:
info blanket_f:module already loaded:splash:
info milestone:19.84:pi00:
info milestone:20.06:pi99:
info system:emiting_event:contentpack_font_ready:
debug sytem:event_emitted:contentpack_font_ready:
info milestone:23.25:fr00:
info milestone:23.42:fr50:
info milestone:23.47:fr51:
info framework:starting:time=25680:
info hardware:no_wan::WiFi only device. No WAN found
info board_data_file :/opt/ar6k/target/AR6003/hw2.1.1/bin/wario/icewine/wfo/AR6003_wfo_calfile.bin::
[ 29.515707] ath6kl: ath6kl_fetch_board_file: Board calibration file fetched: /opt/ar6k/target/AR6003/hw2.1.1/bin/wario/icewine/wfo/AR6003_wfo_calfile.bin
[ 29.649762] ath6kl: MAC from kernel xx:xx:xx:xx:xx:72
[ 30.075672] ath6kl: host only supports scatter of :1 entries, need: 16
Welcome to Kindle!
kindle login: info milestone:53.87:fr99:
info framework:started:time=53900,delta=30450:
info blanket_f:loading blanket module:usb:
info framework_setup:password=disabled:showing screensaver:
info blanket_f:unloading blanket module:splash:
info system:emiting_event:framework_ready:
debug sytem:event_emitted:framework_ready:
info stored:started::
info stored:read_in_counters:REBOOTS=0, REBOOT_LIMIT=1, RESTARTS=0, RESTART_LIMIT=5:
info monitor:writing_file:file=/var/run/upstart/stored.restarts:
Retrieved 334 keys for system/daemon/pmond/
Welcome to Kindle!
kindle login:
 Code:
info framework_setup:password=disabled:showing screensaver: Thanks in advance! 
|
|
|
|
01-25-2016, 08:29 AM
|
#2 |
|
Going Viral
 
Posts: 17,212
Karma: 18210809
Join Date: Feb 2012
Location: Central Texas
Device: No K1, PW2, KV, KOA
|
Nothing jumps out at me and says: "THIS IS IT!"
The early failures to setup lipc seem strange, but I **think** I have seen those before from a device that is working normally. The recent thread about using fastboot to recover an erased Kindle PW-3: https://www.mobileread.com/forums/sho...d.php?t=269099 has a lot of serial I/O capture logs attached to it. (Which I think you have seen, your post reads as if you have anyway.) Read through yours above and some of the later ones (after we used the recovery menu to re-load the factory Update image) side-by-side. Clip out and quote any differences you find. Keep in mind that since it is a different device, there may be minor filename differences, but they are both 5.6.5 @MadMAXXX : See, I knew we would find a use for all of those log files. 
Last edited by knc1; 01-25-2016 at 08:31 AM. |
|
|
|
| Advert | |
|
|
|
01-25-2016, 09:19 AM
|
#3 |
|
Member
Posts: 21
Karma: 10
Join Date: Mar 2015
Device: PW, PW2, KV
|
Hi Knc1,
I've checked and compared the following log with mine: Log_Recovery.rar It looks identical with the licp failures which is included in MadMAXXX's log Here is the plus lines what is included in my log and not in MadMAXXX's: Code:
info modules:modprobe:loading module als_max44009: info system:emiting_event:loaded_als_max44009: debug sytem:event_emitted:loaded_als_max44009: . . [ 12.036022] [DRV26XX]Found matching id! [ 12.044917] [DRV26XX]Probe succeeded! info userstore:run:time=12140,action=start: info userstore:start:found_bootup_flag:Found BOOTUP flag file . . [ 12.258694] fsr_config: n_adc=6, adc_depth=16, app_ver=10, n_buttons=4, flash=8000 info fsr_keypad:adc:1528 1908 1240 1630, 0 0: info fsr_keypad:calibration: 4 3 1 0 250 500 0 0 0 0 0 1320 1577 1856 48879 48879 48879 48879 48879 1727 2122 2329 48879 48879 48879 48879 48879 411 804 1342 48879 48879 48879 48879 48879 2091 2270 2422 48879 48879 48879 48879 48879 : info fsr_keypad:update:fsr app version=0x0010: info system:emiting_event:loaded_touch: debug sytem:event_emitted:loaded_touch: . . info locale:read:lang=en_GB.utf8,lc_all=en_GB.utf8:Retrieved Language . . info framework_setup:password=disabled:showing screensaver: 
|
|
|
|
|
01-25-2016, 09:44 AM
|
#4 |
|
Going Viral
Posts: 17,212
Karma: 18210809
Join Date: Feb 2012
Location: Central Texas
Device: No K1, PW2, KV, KOA
|
That last line is a result, not a cause.
Did this device ever work properly? Can you exchange it for a new one? (Opening it and adding the serial port has nothing to do with this failure.) Did you modify the /etc/passwd or /etc/shadow file of the 'main' operating system? Have you tried running the 'diags' operating system?
With what result/observations? And if nothing else seems possible - would you be interested in trying to re-install the original factory firmware install? (We (well, several of us) have a copy of the pre-shipment factory install but no one has ever tried it on a device in the field.) |
|
|
|
|
01-25-2016, 09:50 AM
|
#5 |
|
Member
Posts: 21
Karma: 10
Join Date: Mar 2015
Device: PW, PW2, KV
|
I don't know the past of the device, i've bought it in this condition for a good price.
No, i can't exchange it. As i worte i don't the past of the device so i don't know if the passwd and shadow files are modified or not. I assume they are untouched. Yes, i've been in diags and everything seems to be OK. The touch is working, the lights are working when running the tests. If you need athor informations from diags please let me know! Of course i'm interested in factory firmware as if nothing helps then i'm happy to help the community in experimentation
|
|
|
|
| Advert | |
|
|
|
01-25-2016, 10:09 AM
|
#6 | |
|
Going Viral
Posts: 17,212
Karma: 18210809
Join Date: Feb 2012
Location: Central Texas
Device: No K1, PW2, KV, KOA
|
Quote:
That may not be so, but that will be our assumption until we learn differently. When you followed the directions to re-install the Amazon 5.6.5 update package, that should have replaced any file modifications made to the 'main' system. That is a complete, 'main' system image. It **should** have fixed anything except damaged hardware. (It is what I would have recommended if you had posted here before doing it.) Make sure you are subscribed to this thread so you get an e-mail notification of posts here. I will find where on the Internet I stored that factory file and make a follow-up post when things are ready to continue. (RSN, hours (because I may have to move it around), not days) - - - - While viewing this thread - - In the top blue bar, the 'thread tools' drop down box - - That is where you will find the subscription controls. Last edited by knc1; 01-25-2016 at 10:17 AM. |
|
|
|
|
|
01-25-2016, 02:33 PM
|
#7 |
|
Going Viral
Posts: 17,212
Karma: 18210809
Join Date: Feb 2012
Location: Central Texas
Device: No K1, PW2, KV, KOA
|
I'll PM you a temporary download link.
Here is what KindleTool has to say about the file: Code:
Extracting update package 'update_20141128.bin' to 'kv-package'. Bundle FB02 (Fullbin [signed?]) Bundle Type Recovery MD5 Hash d5c1754684f8744abc18692ef9d154f6 Magic 1 2048630901 Magic 2 1897089723 Minor 1 Header Rev 2 Platform Wario Board Unspecified x update-J5-wario_icewine-049.dat x imx60_wario/u-boot.bin x imx60_wario/u-boot.bin.sig x imx60_wario/uImage x imx60_wario/uImage.sig x rootfs.img.gz x rootfs.img.gz.sig x data.stgz x data.stgz.sig x update-J5-wario_icewine-049.dat.sig If you can't see the USB storage when you connect to your PC, you can use the recovery menu (below). You will want to repeat the booting into diags (directions given above), only this time, catch this stopping point: Code:
3.0.35-lab126 #1 PREEMPT Fri Jul 31 15:04:21 PDT 2015 armv7l Press [ENTER] for recovery menu... Now you will be using the touch screen. Please stay away from the "Erase MMC" selection - yes, it does work - no need to try it out. If you haven't yet put the factory install file on USB visible storage, then: Use the recovery menu to export USB storage (user storage) Connect Kindle-to-PC cable copy the update file to the top level of visible storage safely remove or eject - depending on your PC system Remove Kindle-to-PC cable Note: you may have to un-export USB storage at this point. Now use the: "load mmc from update file" selection. (or whatever it is called - the above is what my memory returns) Note: you may have to go through the re-boot, boot diags, catch the Recovery Menu sequence again, just to reach the above command selection. (Translation: I don't recall if it can be updated while the USB storage is exported.) Edit: PM sent. Last edited by knc1; 01-25-2016 at 02:38 PM. |
|
|
|
|
01-25-2016, 02:43 PM
|
#8 |
|
Member
Posts: 21
Karma: 10
Join Date: Mar 2015
Device: PW, PW2, KV
|
Thanks!
I've started to download the file, but it's a little slow... But who cares maybe it'll fix my Kindle As soon as the file is downloaded, i'll try it and let you know the result! Thanks in advance! |
|
|
|
|
01-25-2016, 03:35 PM
|
#9 | |
|
Going Viral
Posts: 17,212
Karma: 18210809
Join Date: Feb 2012
Location: Central Texas
Device: No K1, PW2, KV, KOA
|
Quote:
And it depends on what part of the world your in - that link is to the USA, there is another archive set in a European cloud (not owned by myself). |
|
|
|
|
|
01-26-2016, 02:59 AM
|
#10 |
|
Member
Posts: 21
Karma: 10
Join Date: Mar 2015
Device: PW, PW2, KV
|
So i've used knc1's flash file and flashed the device with FW version 5.5.0
Here is the update log. It looks like everyhing went OK: Code:
U-Boot 2009.08-lab126 (Dec 10 2014 - 13:25:46)
CPU: Freescale i.MX6 family TO0.0 at 996 MHz
Temperature: 32 C, calibration data 0x5775015f
mx6sl pll1: 996MHz
mx6sl pll2: 528MHz
mx6sl pll3: 480MHz
mx6sl pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 66000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 198000000Hz
emi_slow clock: 22000000Hz
ddr clock : 396000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
MMC: FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2
Board: Icewine WFO 512
Boot Reason: [ POR ]
Boot Device: NAND
Board Id:
S/N:
I2C: ready
DRAM: 512 MB
Using default environment
In: serial
Out: serial
Err: serial
Quick Memory Test 0x80000000, 0x1fff0000
POST done in 115 ms
Battery voltage: 4266 mV
check_haptic: ID = 0x07
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at 80800000 ...
Image Name: Linux-3.0.35-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2633728 Bytes = 2.5 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.098518] No Legacy reboot reason code to print
[ 0.287838] LPDDR2 MfgId: 0x1 [Samsung]
[ 0.291701]
[ 0.291705] just text: vaddr c0150d44, va 0xc0150200 pa 0x801000c3 attr 0x6
[ 0.304238]
[ 0.304242] nmx6sl_wfi_iram: vaddr e084e000, va 0xe084e200 pa 0x904043 attr 0x2
[ 0.313118]
[ 0.313121] mx6sl_ddr: vaddr e0856000, va 0xe0856200 pa 0x905043 attr 0x2
[ 0.321466]
[ 0.321469] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149
[ 0.332240]
[ 0.332244] ANATOP: vaddr f40c8000, va 0xf40c8200 pa 0x20110c3 attr 0x149
[ 0.345637]
[ 0.345640] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149
[ 0.355618]
[ 0.355621] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149
[ 0.368096]
[ 0.368099] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149
[ 0.377971]
[ 0.377974] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149
3.0.35-lab126 #1 PREEMPT Fri Jul 31 15:04:21 PDT 2015 armv7l
Press [ENTER] for recovery menu... 0 /
Charge: 96% [#########################################################:]
Menu
====
3. Load MMC0 over USB storage
4. Erase MMC0
I. Initialize Partition Table (fdisk) and format FAT
O. Format and overwrite FAT partition
E. Export FAT partition
U. Update using update*.bin file on FAT partition
M. Update using update*.bin file on FAT partition of second MMC port
D. dmesg / kernel printk ring buffer.
Q. quit
Choose: e /
Charge: 96% [#########################################################:]
[FAT32]
1. done
R. reboot
Choose: /
USB CONNECTED!!
Charge: 86% [###################################################:::::::]
[FAT32]
1. done
R. reboot
Choose: \
Charge: 86% [###################################################:::::::]
[FAT32]
1. done
R. reboot
Choose: -still alive...
Charge: 87% [####################################################::::::]
[FAT32]
1. done
R. reboot
Choose: -still alive...
Charge: 87% [####################################################::::::]
[FAT32]
1. done
R. reboot
Choose: -still alive...
Charge: 87% [####################################################::::::]
[FAT32]
1. done
R. reboot
Choose: -
USB DISCONNECTED!!
Charge: 88% [####################################################::::::]
Menu
====
3. Load MMC0 over USB storage
4. Erase MMC0
I. Initialize Partition Table (fdisk) and format FAT
O. Format and overwrite FAT partition
E. Export FAT partition
U. Update using update*.bin file on FAT partition
M. Update using update*.bin file on FAT partition of second MMC port
D. dmesg / kernel printk ring buffer.
Q. quit
Choose: u |
/dev/mmcblk0p4:
CHS=4/16/101312 size=3319791616 bytes
flag type first last lba first lba size
Partition p1:
0x00 0x0b 16 <large> 16 6483952
CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
update-J5-wario_icewine-049.dat:128 45d8e89a3debd55084609dddd2d461e4 imx60_wario/u-boot.bin 2 bootloader_bin
1 50843127fd2bf98cccc8329e34c20268 imx60_wario/uImage 20 main_kernel
128 2b5426871c8b84106f02f806ae7b1924 rootfs.img.gz 1702 update_image_rootfs
128 5800e2bd56c61eec658d5b73ab14eff5 data.stgz 2471 update_data_data
update-J5-wario_icewine-049.dat:EOF
imx60_wario/u-boot.bin 270804 [######################################]
imx60_wario/uImage 2621440 [######################################]
rootfs.img.gz 223209561 [######################################]
data.stgz 323906340 [######################################]
imx60_wario/u-boot.bin 270804 [######################################]
imx60_wario/uImage 2621440 [######################################]
rootfs.img.gz 223209561 [######################################]
data.stgz 323906340 [######################################]
2621440 [######################################]
270804 [######################################]
=== kernel printk buffer (23767 bytes) ===
<5>[ 0.000000] Linux version 3.0.35-lab126 (jenkins-official@sjc10-jbuild07) (collect2: error: ld returned 1 exit status) #1 PREEMPT Fri Jul 31 15:04:21 PDT 2015
<4>[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
<4>[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
<4>[ 0.000000] Machine: Freescale i.MX 6SoloLite based Wario Board
<6>[ 0.000000] Will try to place printk log at 8fffc000
<4>[ 0.000000] Memory policy: ECC disabled, Data cache writeback
<6>[ 0.000000] CPU identified as i.MX6SoloLite, silicon rev 1.2
<7>[ 0.000000] On node 0 totalpages: 131072
<7>[ 0.000000] free_area_init_node: node 0, pgdat c054d698, node_mem_map c2000000
<7>[ 0.000000] DMA zone: 64 pages used for memmap
<7>[ 0.000000] DMA zone: 0 pages reserved
<7>[ 0.000000] DMA zone: 8128 pages, LIFO batch:0
<7>[ 0.000000] Normal zone: 960 pages used for memmap
<7>[ 0.000000] Normal zone: 121920 pages, LIFO batch:31
<7>[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>[ 0.000000] pcpu-alloc: [0] 0
<4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
<5>[ 0.000000] Kernel command line: rootwait log_pos_goal=0x8fffc000 console=ttymxc0,115200 root=/dev/mmcblk0p1 ro ip=off quiet video=mxcepdcfb:E60,bpp=8,x_mem=3M
<4>[ 0.000000] Prink buffer will be relocated to physical address: 8fffc000
<6>[ 0.000000] log_buf_len: 32768
<6>[ 0.000000] early log buf free: 31323(95%)
<6>[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
<6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>[ 0.000000] Memory: 512MB = 512MB total
<5>[ 0.000000] Memory: 514104k/514104k available, 10184k reserved, 0K highmem
<5>[ 0.000000] Virtual kernel memory layout:
<5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
<5>[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
<5>[ 0.000000] DMA : 0xfde00000 - 0xffe00000 ( 32 MB)
<5>[ 0.000000] vmalloc : 0xe0800000 - 0xf2000000 ( 280 MB)
<5>[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
<5>[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
<5>[ 0.000000] .init : 0xc0008000 - 0xc013e000 (1240 kB)
<5>[ 0.000000] .text : 0xc013e000 - 0xc051a000 (3952 kB)
<5>[ 0.000000] .data : 0xc051a000 - 0xc054e1c0 ( 209 kB)
<5>[ 0.000000] .bss : 0xc054e1e4 - 0xc0573a60 ( 151 kB)
<6>[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
<6>[ 0.000000] Preemptible hierarchical RCU implementation.
<6>[ 0.000000] Verbose stalled-CPUs detection is disabled.
<6>[ 0.000000] NR_IRQS:624
<6>[ 0.000000] MXC GPIO hardware
<6>[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
<6>[ 0.000000] arm_max_freq=1GHz
<6>[ 0.000000] MXC_Early serial console at MMIO 0x2020000 (options '115200')
<6>[ 0.000000] bootconsole [ttymxc0] enabled
<6>[ 0.000000] Console: colour dummy device 80x30
<6>[ 0.000260] Calibrating delay loop... 1980.82 BogoMIPS (lpj=9904128)
<6>[ 0.060091] pid_max: default: 32768 minimum: 301
<6>[ 0.060341] Mount-cache hash table entries: 512
<6>[ 0.060688] CPU: Testing write buffer coherency: ok
<6>[ 0.060831] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
<6>[ 0.067877] print_constraints: dummy:
<6>[ 0.068046] NET: Registered protocol family 16
<6>[ 0.072521] print_constraints: vddpu: 725 <--> 1300 mV at 700 mV fast normal
<6>[ 0.072844] print_constraints: vddcore: 725 <--> 1300 mV at 1475 mV fast normal
<6>[ 0.073168] print_constraints: vddsoc: 725 <--> 1300 mV at 1475 mV fast normal
<6>[ 0.073495] print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
<6>[ 0.073854] print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal
<6>[ 0.074194] print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal
<4>[ 0.075975] LAB126 Board id -
<6>[ 0.080728] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
<6>[ 0.080742] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
<6>[ 0.080755] hw-breakpoint: maximum watchpoint size is 4 bytes.
<6>[ 0.080774] L310 cache controller enabled
<6>[ 0.080786] l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x02030000, Cache size: 262144 B
<6>[ 0.090294] bio: create slab <bio-0> at 0
<6>[ 0.094498] max77696> regulator init
<6>[ 0.095510] spi_imx imx6q-ecspi.0: probed
<6>[ 0.095917] usbcore: registered new interface driver usbfs
<6>[ 0.096046] usbcore: registered new interface driver hub
<6>[ 0.096204] usbcore: registered new device driver usb
<4>[ 0.098463] Reboot Reason - Metric Framework Reporting
<6>[ 0.098478] kernel: kernel_metric_generic,0,counter,event_recorder,ercflags,MR_FRSTRT,1,
<4>[ 0.098487] Reboot Reason - Legacy Metric Reporting
<3>[ 0.098494] boot: C def:bcut:batterycut=1
<6>[ 0.104119] MAX77696 TOPSYS 1.0.0 Installed
<6>[ 0.106845] max77696-gpio max77696-gpio.0: gpio#0 -- -- func-0 in
<6>[ 0.108314] max77696-gpio max77696-gpio.0: gpio#1 -- -- func--1 in
<6>[ 0.109781] max77696-gpio max77696-gpio.0: gpio#3 -- -- func-0 in
<6>[ 0.111633] MAX77696 GPIO Driver 1.0.0 Installed
<4>[ 0.112933] buck mode: 4
<4>[ 0.113683] buck mode: 4
<6>[ 0.114633] print_constraints: max77696_buck1: 900 <--> 1300 mV at 1250 mV fast normal idle standby
<4>[ 0.115254] buck mode: 4
<6>[ 0.116211] print_constraints: max77696_buck1dvs: 600 <--> 1300 mV at 900 mV fast normal idle standby
<4>[ 0.116801] buck mode: 4
<4>[ 0.117542] buck mode: 4
<6>[ 0.118490] print_constraints: max77696_buck2: 900 <--> 1300 mV at 1200 mV fast normal idle standby
<4>[ 0.119047] buck mode: 4
<6>[ 0.119995] print_constraints: max77696_buck2dvs: 600 <--> 1300 mV at 900 mV fast normal idle standby
<6>[ 0.120556] print_constraints: max77696_buck3: 600 <--> 3387 mV at 1300 mV fast normal idle standby
<4>[ 0.121284] buck mode: 4
<4>[ 0.122026] buck mode: 4
<6>[ 0.122794] print_constraints: max77696_buck4: 1200 mV fast normal idle standby
<4>[ 0.123366] buck mode: 4
<6>[ 0.124319] print_constraints: max77696_buck5: 600 <--> 3387 mV at 1800 mV fast normal idle standby
<4>[ 0.124892] buck mode: 2
<6>[ 0.125844] print_constraints: max77696_buck6: 600 <--> 3387 mV at 3200 mV fast normal idle standby
<6>[ 0.125889] MAX77696 Buck Regulators Driver 1.0.1 Installed
<6>[ 0.126754] print_constraints: max77696_ldo1: 800 <--> 3950 mV at 3300 mV normal idle standby
<6>[ 0.127354] print_constraints: max77696_ldo2: 800 <--> 3950 mV at 3000 mV normal idle standby
<6>[ 0.127938] print_constraints: max77696_ldo3: 800 <--> 3950 mV at 2500 mV normal idle standby
<6>[ 0.128509] print_constraints: max77696_ldo4: 800 <--> 2375 mV at 1800 mV normal idle standby
<6>[ 0.129082] print_constraints: max77696_ldo5: 800 <--> 2375 mV at 1800 mV normal idle standby
<6>[ 0.129665] print_constraints: max77696_ldo6: 800 <--> 3950 mV at 3200 mV normal idle standby
<6>[ 0.130246] print_constraints: max77696_ldo7: 800 <--> 3950 mV at 3200 mV normal idle standby
<6>[ 0.130817] print_constraints: max77696_ldo8: 800 <--> 2375 mV at 1100 mV normal idle standby
<6>[ 0.131404] print_constraints: max77696_ldo9: 800 <--> 2375 mV at 1100 mV normal idle standby
<6>[ 0.131984] print_constraints: max77696_ldo10: 2400 <--> 5550 mV at 5200 mV normal idle standby
<6>[ 0.132864] MAX77696 Linear Regulators Driver 1.0.2 Installed
<6>[ 0.133577] print_constraints: max77696_lsw1:
<6>[ 0.133969] print_constraints: max77696_lsw2:
<6>[ 0.134315] print_constraints: max77696_lsw3:
<6>[ 0.134661] print_constraints: max77696_lsw4:
<6>[ 0.134704] MAX77696 Load Switches Driver 1.0.0 Installed
<6>[ 0.135960] print_constraints: max77696-display:
<6>[ 0.136747] print_constraints: max77696-vcom:
<6>[ 0.137101] print_constraints: max77696-vee:
<6>[ 0.137479] print_constraints: max77696-vneg:
<6>[ 0.137863] print_constraints: max77696-vpos:
<6>[ 0.138216] print_constraints: max77696-vddh:
<6>[ 0.139223]
<6>[ 0.139227] EPD vreg probe complete!
<6>[ 0.139856] print_constraints: max77696_vddq: 240 <--> 984 mV at 600 mV
<6>[ 0.139915] MAX77696 LPDDR2 Termination Supply Driver 1.0.1 Installed
<6>[ 0.141368] MAX77696 I2C Driver 1.0.0 Installed
<4>[ 0.144788] i2c-core: driver [max17135] using legacy suspend method
<4>[ 0.144799] i2c-core: driver [max17135] using legacy resume method
<6>[ 0.144832] Switching to clocksource mxc_timer1
<6>[ 0.157161] NET: Registered protocol family 2
<6>[ 0.157254] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>[ 0.157442] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
<6>[ 0.157673] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
<6>[ 0.157814] TCP: Hash tables configured (established 16384 bind 16384)
<6>[ 0.157823] TCP reno registered
<6>[ 0.157832] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.157849] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.158158] NET: Registered protocol family 1
<6>[ 0.158358] RPC: Registered named UNIX socket transport module.
<6>[ 0.158369] RPC: Registered udp transport module.
<6>[ 0.158376] RPC: Registered tcp transport module.
<6>[ 0.158384] RPC: Registered tcp NFSv4.1 backchannel transport module.
<4>[ 0.163113] etb: probe of etb failed with error -2
<4>[ 0.163420] etm: probe of etm.0 failed with error -2
<6>[ 0.163714] Static Power Management for Freescale i.MX6
<6>[ 0.163725] wait mode is enabled for i.MX6
<6>[ 0.163889] cpaddr = 0 suspend_iram_base=f2900000
<6>[ 0.163933] PM driver module loaded
<6>[ 0.164218] IMX usb wakeup probe
<7>[ 0.164241] the wakeup pdata is 0xde0936c0
<6>[ 0.164603] IMX usb wakeup probe
<7>[ 0.164625] the wakeup pdata is 0xde093840
<6>[ 0.164790] cpu regulator mode:ldo_bypass
<6>[ 0.165225] i.MXC CPU frequency driver
<6>[ 0.186271] squashfs: version 4.0 (2009/01/31) Phillip Lougher
<6>[ 0.187359] msgmni has been set to 1004
<6>[ 0.187846] io scheduler noop registered
<6>[ 0.187929] io scheduler cfq registered (default)
<6>[ 0.188405] MAX77696 Backlight Driver 1.0.0 Installed
<6>[ 0.189247] imx-sdma imx-sdma: loaded firmware 1.1
<6>[ 0.194177] imx-sdma imx-sdma: initialized
<6>[ 0.197046] Serial: IMX driver
<6>[ 0.197162] imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
<6>[ 0.197189] console [ttymxc0] enabled, bootconsole disabled
<6>[ 0.201316] loop: module loaded
<6>[ 0.201574] MAX77696 32kHz Oscillator Driver 1.0.0 Installed
<6>[ 0.202200] input: max77696-onkey as /devices/platform/imx-i2c.0/i2c-0/0-003c/max77696-onkey.0/input/input0
<6>[ 0.205460] MAX77696 ONKEY Driver 1.0.0 Installed
<6>[ 0.226151] max77696-rtc max77696-rtc.0: rtc core: registered max77696-rtc.0 as rtc0
<6>[ 0.246081] max77696-rtc max77696-rtc.0: rtc core: registered max77696-rtc.1 as rtc1
<6>[ 0.265484] MAX77696 RTC Driver 1.0.2 Installed
<6>[ 0.266224] snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc2
<6>[ 0.266405] i2c /dev entries driver
<6>[ 0.270448] max77696-battery max77696-battery.0: Voltage alert 3400mV ... 4400mV
<6>[ 0.270860] max77696-battery max77696-battery.0: SOC alert (disabled)
<6>[ 0.271782] MAX77696 Fuel Gauge Driver 1.0.0 Installed
<6>[ 0.273676] MAX77696 USB Interface Circuit Driver 1.0.0 Installed
<6>[ 0.275423] max77696-adc max77696-adc.0: ADC average rate: 32 sample(s)
<6>[ 0.275435] max77696-adc max77696-adc.0: ADC delay: 0 nsec
<6>[ 0.275444] max77696-adc max77696-adc.0: ADC cur src: 50 uA
<6>[ 0.275456] MAX77696 ADC Driver 1.0.1 Installed
<6>[ 0.276053] imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
<6>[ 0.276885] sdhci: Secure Digital Host Controller Interface driver
<6>[ 0.276894] sdhci: Copyright(c) Pierre Ossman
<6>[ 0.277006] mmc0: no vmmc regulator found
<7>[ 0.278025] sdhci: =========== REGISTER DUMP (mmc0)===========
<4>[ 0.278034]
<4>[ 0.278036] 0xe0858000: 00000000 00010200 00000000 083a0000
<4>[ 0.278050] 0xe0858010: 00000900 ffffffff 320f5903 00000b00
<4>[ 0.278061] 0xe0858020: 00000000 ff888088 08800024 008e0118
<4>[ 0.278073] 0xe0858030: 00000000 007f0003 007f0003 00000000
<4>[ 0.278084] 0xe0858040: 07f3b407 08000880 00000011 00000000
<4>[ 0.278096] 0xe0858050: 00000000 00000000 00000000 00000000
<4>[ 0.278106] 0xe0858060: 00000000 00000200 00000000 0800ff00
<4>[ 0.278117] 0xe0858070: 00000000 00000000 00000000 00000000
<4>[ 0.278128] 0xe0858080: 00000000 00000000 00000000 00000000
<4>[ 0.278139] 0xe0858090: 00000000 00000000 00000000 00000000
<4>[ 0.278149] 0xe08580a0: 00000000 00000000 00000000 00000000
<4>[ 0.278160] 0xe08580b0: 00000000 00000000 00000000 00000000
<4>[ 0.278170] 0xe08580c0: 2000780b 00000000 00000006 00212800
<7>[ 0.278184] CCM: CSCMR1(0x00900040), CSCDR1(0x00490b40)
<7>[ 0.278192] CCM: CCOSR(0x000a000c), CCGR6(0x00000030)
<7>[ 0.278199] CCM: CMEOR(0x7fffffff)
<7>[ 0.278205] sdhci: ===========================================
<6>[ 0.278554] mmc0: SDHCI controller on platform [sdhci-esdhc-imx.1] using DMA
<6>[ 0.279624] mmc1: no vmmc regulator found
<7>[ 0.280642] sdhci: =========== REGISTER DUMP (mmc1)===========
<4>[ 0.280650]
<4>[ 0.280653] 0xe0860000: 00000000 00010000 00000000 00000000
<4>[ 0.280665] 0xe0860010: 00000000 00000000 00000000 00000000
<4>[ 0.280676] 0xe0860020: 00000000 ff888088 08800020 0080800f
<4>[ 0.280688] 0xe0860030: 00000000 007f0003 007f0003 00000000
<4>[ 0.280699] 0xe0860040: 07f3b407 08100810 80000000 00000000
<4>[ 0.280710] 0xe0860050: 00000000 00000000 00000000 00000000
<4>[ 0.280721] 0xe0860060: 00000000 00000200 00000000 0800ff00
<4>[ 0.280732] 0xe0860070: 00000000 00000000 00000000 00000000
<4>[ 0.280742] 0xe0860080: 00000000 00000000 00000000 00000000
<4>[ 0.280752] 0xe0860090: 00000000 00000000 00000000 00000000
<4>[ 0.280762] 0xe08600a0: 00000000 00000000 00000000 00000000
<4>[ 0.280772] 0xe08600b0: 00000000 00000000 00000000 00000000
<4>[ 0.280782] 0xe08600c0: 2000780b 00000000 00000006 00212800
<7>[ 0.280795] CCM: CSCMR1(0x00900040), CSCDR1(0x00490b40)
<7>[ 0.280803] CCM: CCOSR(0x000a000c), CCGR6(0x000000c0)
<7>[ 0.280809] CCM: CMEOR(0x7fffffff)
<7>[ 0.280815] sdhci: ===========================================
<6>[ 0.280911] mmc0: mmc_rescan_try_freq: trying to init card at 400000 Hz
<6>[ 0.282267] mmc1: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA
<7>[ 0.282974] Registered led device: max77696-leds.0
<6>[ 0.282984] MAX77696 LED Driver #0 1.0.0 Installed
<7>[ 0.283159] Registered led device: max77696-leds.1
<6>[ 0.283168] MAX77696 LED Driver #1 1.0.0 Installed
<6>[ 0.283603] nf_conntrack version 0.5.0 (8032 buckets, 32128 max)
<6>[ 0.284278] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 0.284343] TCP cubic registered
<6>[ 0.284354] NET: Registered protocol family 17
<6>[ 0.284375] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
<3>[ 0.284520] LPDDR2 MfgId: 0x1 [Samsung]
<3>[ 0.288594]
<3>[ 0.288598] just text: vaddr c0150d44, va 0xc0150200 pa 0x801000c3 attr 0x6
<3>[ 0.301130]
<3>[ 0.301134] nmx6sl_wfi_iram: vaddr e084e000, va 0xe084e200 pa 0x904043 attr 0x2
<3>[ 0.309981]
<3>[ 0.309983] mx6sl_ddr: vaddr e0856000, va 0xe0856200 pa 0x905043 attr 0x2
<3>[ 0.318392]
<3>[ 0.318395] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149
<3>[ 0.329162]
<3>[ 0.329165] ANATOP: vaddr f40c8000, va 0xf40c8200 pa 0x20110c3 attr 0x149
<3>[ 0.343495]
<3>[ 0.343498] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149
<3>[ 0.355618]
<3>[ 0.355621] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149
<3>[ 0.366042]
<3>[ 0.366045] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149
<3>[ 0.375995]
<3>[ 0.375998] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149
<6>[ 0.386780] Bus freq driver module loaded
<6>[ 0.386792] Bus freq driver Enabled
<6>[ 0.395151] mxc_dvfs_core_probe
<6>[ 0.395402] DVFS driver module loaded
<4>[ 0.397277] regulator_init_complete: max77696_ldo10: incomplete constraints, leaving on
<4>[ 0.397912] regulator_init_complete: max77696_ldo7: incomplete constraints, leaving on
<4>[ 0.398132] regulator_init_complete: max77696_ldo6: incomplete constraints, leaving on
<4>[ 0.399384] regulator_init_complete: max77696_buck6: incomplete constraints, leaving on
<4>[ 0.399604] regulator_init_complete: max77696_buck5: incomplete constraints, leaving on
<4>[ 0.400066] regulator_init_complete: max77696_buck2dvs: incomplete constraints, leaving on
<4>[ 0.400290] regulator_init_complete: max77696_buck1dvs: incomplete constraints, leaving on
<6>[ 0.416768] max77696-rtc max77696-rtc.0: setting system clock to 2000-01-01 01:17:55 UTC (946689475)
<6>[ 0.428753] KERNEL: I pmic:charger chgina::charger connected
<6>[ 0.434048] MAX77696 Main Charger Driver 1.0.0 Installed
<6>[ 0.437310] MAX77696 Energy Harvester Driver 1.0.0 Installed
<6>[ 0.437903] Freeing init memory: 1240K
<6>[ 0.445822] emmc: I def:mmcpartinfo:vendor=toshiba, host=mmc0:
<6>[ 0.480165] mmc0: new high speed DDR MMC card at address 0001
<6>[ 0.480477] mmcblk0: mmc0:0001 004G90 3.68 GiB
<6>[ 0.480605] mmcblk0boot0: mmc0:0001 004G90 partition 1 2.00 MiB
<6>[ 0.480736] mmcblk0boot1: mmc0:0001 004G90 partition 2 2.00 MiB
<6>[ 0.481655] mmcblk0: p1 p2 p3 p4
<6>[ 0.483914] mmcblk0boot1: unknown partition table
<6>[ 0.485899] mmcblk0boot0: unknown partition table
<6>[ 0.486088] mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz
<6>[ 0.563581] mmc1: mmc_rescan_try_freq: trying to init card at 300000 Hz
<4>[ 0.563741] mxc_epdc_eink: module license 'proprietary' taints kernel.
<4>[ 0.563750] Disabling lock debugging due to kernel taint
<4>[ 0.564140] INFO:Loaded module /lib/modules/mxc_epdc_eink.ko (10644 bytes)
<6>[ 0.572101] imx_epdc_fb imx_epdc_fb: Found a video mode override (EBA)
<6>[ 0.634539] mmc1: mmc_rescan_try_freq: trying to init card at 200000 Hz
<6>[ 0.707186] mmc1: mmc_rescan_try_freq: trying to init card at 100000 Hz
<6>[ 1.195716] add wake up source irq 104
<6>[ 1.696826] Retrieved voltage control information
<6>[ 2.264907] KERNEL: I pmic:fg battery id check::wario_battery_valid=1
<4>[ 3.777950] INFO:Loaded module /lib/modules/mxc_epdc_fb.ko (90644 bytes)
<4>[ 4.089817] INFO:eink initialized... (1575424 bytes)
<4>[ 5.098110] INFO:!!! Checking MBR /dev/mmcblk0 !!!!
<4>[ 5.102547] INFO:partition 2, start sector is 987136
<4>[ 5.102723] INFO:partition 3, start sector is 1118208
<4>[ 5.102890] INFO:partition 4, start sector is 1249280
<4>[ 5.103021] INFO:maximizing partition 6483968 sectors
<4>[ 5.103074] INFO:*** Partition table verified for /dev/mmcblk0 ***
<4>[ 5.105543] INFO:Setup loop device /dev/loop0 for /dev/mmcblk0p4 + 8192
<4>[ 5.109372] INFO:Checking for updates... (auto-pilot mode)
<4>[ 5.109673] INFO:Found update.bin
<4>[ 5.110655]
<4>[ 5.114067] INFO:Found bundle /mnt-us/update.bin
<4>[ 5.114099] INFO:*** NORMAL MODE
<4>[ 5.306216] *** CHECKING /mnt-us/update.bin ***
<4>[ 6.467805] INFO:do_unbundle: filename=/mnt-us/update.bin, new_file=0x00014eec
<4>[ 6.481419] INFO:Unsigned bundle.
<4>[ 6.511261] IGNORING FILE: update-J5-wario_icewine-049.dat
<4>[ 6.556558] INFO:Total progress is 1%
<4>[ 6.556658] CHK: imx60_wario/u-boot.bin hash for UBoot:
<4>[ 6.556724] MD5: 45d8e89a3debd55084609dddd2d461e4
<4>[ 6.557309] SHA256: 4743ccaeaa4d63b07614ea52f1aa3c5f86b8a76f95bc2c0b01344a58f2a54241
<4>[ 6.558499] SIGNATURE FILE: imx60_wario/u-boot.bin.sig
<4>[ 6.558581] INFO:Total progress is 1%
<4>[ 6.558671] INFO:imx60_wario/u-boot.bin.sig:sig_len=256
<4>[ 7.052968] INFO:Total progress is 3%
<4>[ 7.053061] CHK: imx60_wario/uImage hash for UImage:
<4>[ 7.053126] MD5: 50843127fd2bf98cccc8329e34c20268
<4>[ 7.053698] SHA256: 033f5c7fed80d0f86f3ecf49d26ad6ac0937306e2e6b7199fb5c52b1d40225bb
<4>[ 7.054917] SIGNATURE FILE: imx60_wario/uImage.sig
<4>[ 7.055019] INFO:Total progress is 3%
<4>[ 7.055112] INFO:imx60_wario/uImage.sig:sig_len=256
<4>[ 45.981269] INFO:Total progress is 13%
<4>[ 45.981365] CHK: rootfs.img.gz hash for RootFS:
<4>[ 45.981427] MD5: 2b5426871c8b84106f02f806ae7b1924
<4>[ 45.981982] SHA256: aa9e5fbbc308ab243509bb8da762135ba3aac379b04f86f976b378696b3ae283
<4>[ 45.983162] SIGNATURE FILE: rootfs.img.gz.sig
<4>[ 45.983255] INFO:Total progress is 13%
<4>[ 45.983346] INFO:rootfs.img.gz.sig:sig_len=256
<4>[ 101.693843] INFO:Total progress is 18%
<4>[ 101.693939] CHK: data.stgz hash for Userdata:
<4>[ 101.694001] MD5: 90048c8c851a08cc11003a83ad7554b2
<4>[ 101.694536] SHA256: 406d3462bb7f4a7efa881d1da231ac9213446651d99fb4da0bb7358cea150c16
<4>[ 101.695775] SIGNATURE FILE: data.stgz.sig
<4>[ 101.695866] INFO:Total progress is 18%
<4>[ 101.695958] INFO:data.stgz.sig:sig_len=256
<4>[ 101.696050] SIGNATURE FILE: update-J5-wario_icewine-049.dat.sig
<4>[ 101.696080] IGNORING SIGNATURE FILE: update-J5-wario_icewine-049.dat.sig
<4>[ 101.697725] INFO:*** bundle sizes: UImage[2621440 / 14680064], RootFS[460800000 / 471859200], UBoot[270804 / 385024], DiagsFS[0 / 67108864], Diags Kernel[0 / 14680064], Userdata[323906340 / 2766053376]
<4>[ 101.697927] ERROR: signature is not the correct length (128 bytes versus 256 bytes)
<4>[ 101.704308] INFO:UImage:Present siglen=256 sigpassed=Yes
<4>[ 101.704448] ERROR: signature is not the correct length (128 bytes versus 256 bytes)
<4>[ 101.710801] INFO:RootFS:Present siglen=256 sigpassed=Yes
<4>[ 101.710936] ERROR: signature is not the correct length (128 bytes versus 256 bytes)
<4>[ 101.718277] INFO:UBoot:Present siglen=256 sigpassed=Yes
<4>[ 101.718308] INFO:DiagsFS:missing
<4>[ 101.718330] INFO:Diags Kernel:missing
<4>[ 101.718455] ERROR: signature is not the correct length (128 bytes versus 256 bytes)
<4>[ 101.724687] INFO:Userdata:Present siglen=256 sigpassed=Yes
<4>[ 101.724732] *** UPDATING /mnt-us/update.bin (Attempt #1) ***
<4>[ 101.724928] INFO:do_unbundle: filename=/mnt-us/update.bin, new_file=0x00015f9c
<4>[ 101.763362] INFO:Updating imx60_wario/u-boot.bin
<4>[ 101.807540] INFO:Total progress is 21%
<4>[ 101.807642] INFO:imx60_wario/u-boot.bin update successful
<4>[ 101.807730] INFO:Updating imx60_wario/uImage
<4>[ 102.331055] INFO:Total progress is 23%
<4>[ 102.331150] INFO:imx60_wario/uImage update successful
<4>[ 229.832122] INFO:Total progress is 90%
<4>[ 230.239950] INFO:rootfs.img.gz update successful
<4>[ 230.240471] INFO:Updating data.stgz
<4>[ 358.728284] INFO:Total progress is 100%
<4>[ 358.728397] INFO:data.stgz update successful
<4>[ 358.728894] INFO:Installation had uImage. Installing it.
<4>[ 358.728929] INFO:Copying /uImage to /dev/mmcblk0 ...
<4>[ 359.260365] INFO:Copying /uboot to /dev/mmcblk0boot0 ...
<4>[ 364.233351] INFO:removing /mnt-us/update.bin
<4>[ 364.460302] INFO:bundle /mnt-us/update.bin was successful
<4>[ 366.630518] INFO:Rebooting ...
<6>[ 367.827994] Device spi0.0 removed
=== END ===
[ 376.380796] imx2-wdt imx2-wdt.0: Device shutdown: Expect reboot!
[ 376.388107] Restarting system.
Code:
U-Boot 2009.08-lab126 (Aug 07 2014 - 00:52:13)
CPU: Freescale i.MX6 family TO0.0 at 996 MHz
Temperature: 36 C, calibration data 0x5775015f
mx6sl pll1: 996MHz
mx6sl pll2: 528MHz
mx6sl pll3: 480MHz
mx6sl pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 66000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 198000000Hz
emi_slow clock: 22000000Hz
ddr clock : 396000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
MMC: FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2
Board: Icewine WFO 512
Boot Reason: [ POR ]
Boot Device: NAND
Board Id:
S/N:
I2C: ready
DRAM: 512 MB
Using default environment
In: serial
Out: serial
Err: serial
Quick Memory Test 0x80000000, 0x1fff0000
POST done in 115 ms
Battery voltage: 4293 mV
check_haptic: ID = 0x07
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at 80800000 ...
Image Name: Linux-3.0.35-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2587444 Bytes = 2.5 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.098018]
[ 0.271029] LPDDR2 MfgId: 0x1 [Samsung]
[ 0.275047]
[ 0.275050] just text: vaddr c013d678, va 0xc013d200 pa 0x801000c3 attr 0x6
[ 0.287522]
[ 0.287525] nmx6sl_wfi_iram: vaddr e084e000, va 0xe084e200 pa 0x904043 attr 0x2
[ 0.296369]
[ 0.296372] mx6sl_ddr: vaddr e0856000, va 0xe0856200 pa 0x905043 attr 0x2
[ 0.304711]
[ 0.304715] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149
[ 0.315771]
[ 0.315773] ANATOP: vaddr f40c8000, va 0xf40c8200 pa 0x20110c3 attr 0x149
[ 0.330273]
[ 0.330276] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149
[ 0.342189]
[ 0.342192] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149
[ 0.352667]
[ 0.352670] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149
[ 0.362855]
[ 0.362857] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149
3.0.35-lab126 #1 PREEMPT Thu Aug 7 01:13:39 PDT 2014 armv7l
Press [ENTER] for recovery menu... 0 //dev/mmcblk0p4:
CHS=4/16/101312 size=3319791616 bytes
flag type first last lba first lba size
Partition p1:
0x00 0x0b 16 <large> 16 6483952
CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
BOOTING DEFAULT.
IP-Config: no devices to configure
kinit: Mounted root (ext3 filesystem) readonly.
info sytem:mounted_proc::
info system:mounted_sys::
info firsttime:mount_rw:time=7030:Mounting root RW for first boot
info firsttime:lostfound:Removing lost+found:
info firsttime:mtab:Linking /var/tmp:
info firsttime:mtab:Linking Kindle Registry:
info firsttime:xorgconf:Linking xorg.conf:
info firsttime:cursor:Linking Xorg cursor:
info firsttime:guid:Generating guid:
info firsttime:ssh:Generating rsa keys:
info firsttime:mount_ro:time=8850:Mounting root RO
info system:mounted_dev::
info milestone:8.91:49.1:
info milestone:8.95:49.2:
info milestone:8.97:49.3:
info milestone:9.01:49.4:
info milestone:9.04:49.5:
info sytem:mounted_tmpfs::
info milestone:9.11:sy50:
info system:start:time=9140:
info hardware:no_wan::WiFi only device. No WAN found
info system:config:platform=wario,board=icewine,rev=9,proto=Y,wifi=Y,wan=N:
info milestone:9.29:sy51:
lipc-send-event[830]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[830]: C def:dbusi::Failed to init dbus
lipc-send-event[830]: E def:open::Failed to open LIPC
lipc-send-event[830]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
lipc-send-event[831]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[831]: C def:dbusi::Failed to init dbus
lipc-send-event[831]: E def:open::Failed to open LIPC
lipc-send-event[831]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
info milestone:10.18:sy99:
info system:done:time=10210:
crond[847]: crond: crond (busybox 1.17.1) started, log level 8
init.exe: recevent pre-start process (850) terminated with status 1
info system_cramfs_loopbacks:mountingcramfs:Mounting compressed directories filesystem images:
warn system_cramfs_loopbacks:mountpointmissing:Image /lib/firmware/cyttsp.cramfs.img not mounted, non existing mounting point:
info system_cramfs_loopbacks:mounted:Image /usr/share/X11/xkb.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/java/lib/fonts.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /etc/kdb.src.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/lib/locale.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/share/keyboard.cramfs.img mounted:
info system:emiting_event:mounted_cramfs_loopbacks:
debug sytem:event_emitted:mounted_cramfs_loopbacks:
info milestone:10.96:fs75:
info system:emiting_event:loaded_modules_dependencies:
debug sytem:event_emitted:loaded_modules_dependencies:
info modules:modprobe:loading module g_file_storage:
info system:emiting_event:loaded_g_file_storage:
debug sytem:event_emitted:loaded_g_file_storage:
info modules:modprobe:loading module fuse:
info system:emiting_event:loaded_fuse:
debug sytem:event_emitted:loaded_fuse:
info hardware:no_wan::WiFi only device. No WAN found
info system:emiting_event:loaded_ppp_async:
info milestone:11.23:fs00:
debug sytem:event_emitted:loaded_ppp_async:
info modules:modprobe:loading module als_max44009:
info system:emiting_event:loaded_als_max44009:
debug sytem:event_emitted:loaded_als_max44009:
info system:emiting_event:loaded_fakekey:
debug sytem:event_emitted:loaded_fakekey:
Welcome to Kindle!
kindle login: info milestone:11.70:fs23:
info system:emiting_event:mounted_varLocal:
debug sytem:event_emitted:mounted_varLocal:
info milestone:11.75:fs25:
info milestone:11.77:vi00:
info display:update:Checking '/opt/eink/images/G130_ED060TC1C1' for overrides:
info prereg:PRAGMA_QUICK_CHECK_PASSED::sts=0
[ 13.832035] [DRV26XX]Found matching id!
[ 13.838487] [DRV26XX]Probe succeeded!
[ 14.024025] fsr_config: n_adc=6, adc_depth=16, app_ver=10, n_buttons=4, flash=8000
info milestone:14.09:vi99:
info display:started:time=14100:
info system:emiting_event:display_ready:
debug sytem:event_emitted:display_ready:
info fsr_keypad:adc:1544 2004 1266 1682, 0 0:
info fsr_keypad:calibration:
4 3 1
0 250 500 0 0 0 0 0
1320 1577 1856 48879
48879 48879 48879 48879
1727 2122 2329 48879
48879 48879 48879 48879
411 804 1342 48879
48879 48879 48879 48879
2091 2270 2422 48879
48879 48879 48879 48879 :
info userstore:run:time=14330,action=start:
info userstore:found_bootup_flag::Found BOOTUP flag file
info fsr_keypad:update:fsr app version=0x0010:
info battery:charged:cap=96,mV=4288,mAH=1216:
info system:emiting_event:loaded_touch:
info system:emiting_event:battery_ready:
debug sytem:event_emitted:loaded_touch:
debug sytem:event_emitted:battery_ready:
info userstore:found_data::found data.stgz
Welcome to Kindle!
kindle login: info userstore:extract_data::extracting data.stgz succeeded, removing file
info userstore:extract_data::copying font manifest succeeded
info userstore:extract_data::touching font update skip file succeeded
info system:emiting_event:mounted_userstore:
debug sytem:event_emitted:mounted_userstore:
info milestone:162.47:fs50:
info milestone:162.49:fs90:
info milestone:162.51:fs99:
info milestone:162.54:sys99:
info system:emiting_event:devcap_ready:
debug sytem:event_emitted:devcap_ready:
info system:emiting_event:dbus_ready:
debug sytem:event_emitted:dbus_ready:
info dbus:check-update:status=2:dbus_ready sent
info hardware:no_wan::WiFi only device. No WAN found
info milestone:163.62:xx00:
info X:load:time=163790:
info X:xorg.conf:Generating xorg.conf:
info X:xorg.conf:xorg.conf generated:
info milestone:165.15:xx50:
info X:starting:time=165180:
info milestone:168.07:xx99:
info X:started:time=168100:
info system:emiting_event:x_setup_ready:
debug sytem:event_emitted:x_setup_ready:
info locale:read:lang=en_GB.utf8,lc_all=en_GB.utf8:Retrieved Language
info system:emiting_event:langpicker_ready:
debug sytem:event_emitted:langpicker_ready:
info blanket_f:module already loaded:splash:
info milestone:168.98:pi00:
info milestone:169.18:pi99:
[ 179.172512] ath6kl: ath6kl_fetch_board_file: Board calibration file fetched: /opt/ar6k/target/AR6003/hw2.1.1/bin/active_calibration_ice_wfo
[ 179.260396] ath6kl: MAC from kernel xx:xx:xx:xx:xx:72
[ 179.273854] ath6kl: temporary war to avoid sdio crc error
info system:emiting_event:contentpack_font_ready:
debug sytem:event_emitted:contentpack_font_ready:
info milestone:179.56:fr00:
info milestone:179.67:fr50:
info milestone:179.70:fr51:
[ 179.812955] ath6kl: host only supports scatter of :1 entries, need: 16
info framework:starting:time=179820:
info hardware:no_wan::WiFi only device. No WAN found
info framework:CopyKDKKeystore:Copying internal KDK keystore from /usr/local to /var/local:
info milestone:203.68:fr99:
info framework:started:time=203700,delta=24010:
info blanket_f:loading blanket module:usb:
info blanket_f:unloading blanket module:screensaver:
info blanket_f:module already unloaded:ad_screensaver:
info blanket_f:module already unloaded:ad_screensaver_active:
info blanket_f:loading blanket module:screensaver:
info blanket_f:unloading blanket module:splash:
info system:emiting_event:framework_ready:
debug sytem:event_emitted:framework_ready:
info mesquite:started::
info stored:started::
info mesquite:read_in_counters:REBOOTS=0, REBOOT_LIMIT=1, RESTARTS=0, RESTART_LIMIT=5:
info stored:read_in_counters:REBOOTS=0, REBOOT_LIMIT=1, RESTARTS=0, RESTART_LIMIT=5:
info monitor:writing_file:file=/var/run/upstart/mesquite.restarts:
info monitor:writing_file:file=/var/run/upstart/stored.restarts:
Retrieved 310 keys for system/daemon/pmond/
Welcome to Kindle!
kindle login:
U-Boot version changed: Code:
U-Boot 2009.08-lab126 (Aug 07 2014 - 00:52:13) Code:
info asr_setup:winmgr_running=true. winmgr is ready:: Code:
[ 179.273854] ath6kl: temporary war to avoid sdio crc error Code:
info blanket_f:unloading blanket module:screensaver: info blanket_f:module already unloaded:ad_screensaver: info blanket_f:module already unloaded:ad_screensaver_active: info blanket_f:loading blanket module:screensaver: . . info mesquite:started:: info mesquite:read_in_counters:REBOOTS=0, REBOOT_LIMIT=1, RESTARTS=0, RESTART_LIMIT=5: info monitor:writing_file:file=/var/run/upstart/mesquite.restarts: One interesting thing is that after the update i can't boot into diags: Code:
U-Boot 2009.08-lab126 (Aug 07 2014 - 00:52:13)
CPU: Freescale i.MX6 family TO0.0 at 996 MHz
Temperature: 33 C, calibration data 0x5775015f
mx6sl pll1: 996MHz
mx6sl pll2: 528MHz
mx6sl pll3: 480MHz
mx6sl pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 66000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 198000000Hz
emi_slow clock: 22000000Hz
ddr clock : 396000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
MMC: FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2
Board: Icewine WFO 512
Boot Reason: [ POR ]
Boot Device: NAND
Board Id:
S/N:
I2C: ready
DRAM: 512 MB
Using default environment
In: serial
Out: serial
Err: serial
Quick Memory Test 0x80000000, 0x1fff0000
POST done in 115 ms
Battery voltage: 4250 mV
check_haptic: ID = 0x07
Hit any key to stop autoboot: 1
uboot >
uboot > bootm 0xE41000
## Booting kernel from Legacy Image at 80800000 ...
Image Name: Linux-3.0.35-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2588044 Bytes = 2.5 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.098128] No Legacy reboot reason code to print
[ 0.276523] LPDDR2 MfgId: 0x1 [Samsung]
[ 0.280387]
[ 0.280390] just text: vaddr c013d678, va 0xc013d200 pa 0x801000c3 attr 0x6
[ 0.292915]
[ 0.292919] nmx6sl_wfi_iram: vaddr e084e000, va 0xe084e200 pa 0x904043 attr 0x2
[ 0.301781]
[ 0.301785] mx6sl_ddr: vaddr e0856000, va 0xe0856200 pa 0x905043 attr 0x2
[ 0.310120]
[ 0.310123] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149
[ 0.321256]
[ 0.321259] ANATOP: vaddr f40c8000, va 0xf40c8200 pa 0x20110c3 attr 0x149
[ 0.334762]
[ 0.334765] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149
[ 0.344477]
[ 0.344479] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149
[ 0.356978]
[ 0.356981] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149
[ 0.366800]
[ 0.366803] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149
3.0.35-lab126 #1 PREEMPT Wed Dec 10 23:37:05 PST 2014 armv7l
Press [ENTER] for recovery menu... 0 //dev/mmcblk0p4:
CHS=4/16/101312 size=3319791616 bytes
flag type first last lba first lba size
Partition p1:
0x00 0x0b 16 <large> 16 6483952
CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
BOOTING DEFAULT.
IP-Config: no devices to configure
kinit: Unable to mount root fs on device dev(179,2)
kinit: init not found!
Thats where i'm now. I think it should be a hardware fault, but i don't know which one... And again thanks knc1 for your help!
|
|
|
|
|
01-26-2016, 08:16 AM
|
#11 |
|
Going Viral
Posts: 17,212
Karma: 18210809
Join Date: Feb 2012
Location: Central Texas
Device: No K1, PW2, KV, KOA
|
Code:
kinit: Unable to mount root fs on device dev(179,2) It got trashed in the process. There is no reason to version match parts of 'main' with parts of 'diags' - - The series 5 devices are true 'dual boot' - like having WinXP and Win## installed on the same computer. Not a big deal, you can run approximately forever without 'diags' system. And, it can be installed with fastboot (although you still need the serial port to get into fastboot). Now all we need is a volunteer with a working KV to grab an image copy of the 'diags' kernel and OS file-system (I don't have a KV and neither does NiLuJe). By the way - This device is a KV - since it appears to have working hyptic buttons - but it does not behave as expected for a KV. What are the first six characters of the serial number? <<--- important info. What firmware version (in 'main') is shown as installed? (including build number). Both found at: Home -> Menu -> Settings -> Menu -> Device Info Did you have to re-name the image file I sent you? Did you have to do anything unexpected to use it? The u-boot version **should** have changed, that is expected, since the KV-5.6.5 update package contains a (main) u-boot image. Plus, this is an original factory firmware build, from a machine shipped the first day - Long before the December build date of the u-boot you did have on it. PS: Keep the device away from a network connection - - we don't want it updating to the current 5.6.5 just yet. Plus: It now claims to be a Special Offers device - that wasn't evident before. So it will be hungry for a network connection - keep it off the network. Your (diag) u-boot and kernel/initramfs (a single image file) is working just fine, don't mess with it. The device can be jail broken with what you have now (from the 'diags' initramfs). Although I'll let NiLuJe speak up about where /dev/mmcblk0p1 should be mounted for it to work (it's a recent refinement to the JB process). Last edited by knc1; 01-26-2016 at 08:32 AM. |
|
|
|
|
01-26-2016, 08:34 AM
|
#12 | ||||
|
Member
Posts: 21
Karma: 10
Join Date: Mar 2015
Device: PW, PW2, KV
|
Quote:
Quote:
The version is: 5.5.0 I have to check the build number when i'm home. Quote:
Quote:
Last edited by Atter; 01-26-2016 at 08:39 AM. |
||||
|
|
|
|
01-26-2016, 08:43 AM
|
#13 | |
|
Going Viral
Posts: 17,212
Karma: 18210809
Join Date: Feb 2012
Location: Central Texas
Device: No K1, PW2, KV, KOA
|
Quote:
I thought you reported that 'main' was working normally and only 'diags' did not work. ??? 5.5.0 is the expected version - I'll rename the update file on my cloud. @NiLuJe: B013 09 <<-- that does not have a region mentioned (Australia maybe? It is WiFi only). https://wiki.mobileread.com/wiki/Kindle_Serial_Numbers Crap - we should try to get its initial factory update off of it. Do you have access to a Linux system? Last edited by knc1; 01-26-2016 at 08:46 AM. |
|
|
|
|
|
01-26-2016, 08:52 AM
|
#14 | ||
|
Member
Posts: 21
Karma: 10
Join Date: Mar 2015
Device: PW, PW2, KV
|
Quote:
Quote:
But if it needs serial communication i don't know how to install my USB-TTL cable driver into the linux. And if it would be a VM then i don't know if the USB passthru will or will not work
|
||
|
|
|
|
01-26-2016, 08:52 AM
|
#15 | |
|
Going Viral
Posts: 17,212
Karma: 18210809
Join Date: Feb 2012
Location: Central Texas
Device: No K1, PW2, KV, KOA
|
Quote:
PS: It is the only thing you should be able to do to it - its cyrptographically signed. - - - - My touchscreen pointer ( http://KayNine.Info ) needs a walk, back in a bit. Last edited by knc1; 01-26-2016 at 08:56 AM. |
|
|
|
|
 |
«
Previous Thread
|
Next Thread
»
| Thread Tools | Search this Thread |
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Kindle Voyage Leading Smart Quote Problem | Solo1959 | Amazon Kindle | 6 | 08-31-2015 03:28 PM |
| Problem applying Jailbreak on Kindle Voyage | cookie_swap | Kindle Developer's Corner | 10 | 06-14-2015 05:17 PM |
| Troubleshooting Kindle Voyage Page/Location touch problem/question | solitarywolf | Amazon Kindle | 8 | 03-12-2015 02:52 PM |
| Kindle store problem on voyage | meryvn | Amazon Kindle | 7 | 02-22-2015 04:18 AM |
| problem copying to Kindle Voyage | rbdavis | Calibre | 4 | 12-20-2014 08:06 PM |
All times are GMT -4. The time now is 03:01 PM.