Bebook dead - multiple beep

MacZap · 09-10-2009, 04:26 PM

Hi all,

my Bebook has a problem. When I connect the USB cable to charge the battery, the red LED lighton, then the Bebook plays 5 very fast beeps, and shuts off, totally dead.
If I remove the battery, the Bebook boots normally.

It sems a battery problem, but even change the battery with another (not new) battery, the problem still remain.

Some suggestions?

What it means the 5 fast beep at boot?

thanks

MZ

Kleki · 09-11-2009, 05:19 AM

I have the same problem sometimes. Here's what to do:

1) Take out the battery
2) Boot with USB cable plugged in
3) Replace the battery (cable still plugged in)
4) Wait 10 minutes

Now you should be able to boot without cable again. If not, wait longer in step 4) or try booting with both battery and cable in place.

A similar solution is described on the jinke web site.

While I always get the book working again it is very annoying when this happens out of reach of my laptop. This is really what keeps me from recommending the Hanlin V3.

hth

SDRebel · 09-16-2009, 09:31 PM

I have the astak pocket pro (hanlin v5?) and mine is completely dead with four beeps, any idea what could solve it? astak wants me to send it back. Right now i connected it to power without the battery on and still won't boot. I've already tried all the normal stuff.

MacZap · 09-18-2009, 01:49 AM

Thanks Kleki,

I got the same solution withouth understanding the process.

About the 4 beeps (instead of 5) I never see this problem. Maybe some suggestion is in the Jinke site. Kleki, can you post a link to the Jinke page with this suggestions?

Thanks

MZ

Kleki · 09-18-2009, 04:22 AM

The solution for the not booting problem is described in the Jinke FAQ, # 5. But I do not see anything related to SDRebel's problem there.

EowynCarter · 09-18-2009, 10:20 AM

Quote:

Originally Posted by SDRebel

I have the astak pocket pro (hanlin v5?) and mine is completely dead with four beeps, any idea what could solve it? astak wants me to send it back. Right now i connected it to power without the battery on and still won't boot. I've already tried all the normal stuff.

Try to search astak website for the manual. Else, they probably have a mail / phone contact. And they should be able to tell you what the beeps means.

SDRebel · 09-18-2009, 10:25 AM

Quote:

Originally Posted by EowynCarter

Try to search astak website for the manual. Else, they probably have a mail / phone contact. And they should be able to tell you what the beeps means.

I called them but they couldn't tell me what 4 beeps meant, they just told me to send it back

DaleDe · 09-18-2009, 10:56 AM

4 beeps typically means that the battery has run down completely. Generally recharging the battery will restore operation. It is not recommended to run without a battery installed and it may not even work, I haven't tried it personally.

SDRebel · 09-18-2009, 11:29 AM

Quote:

Originally Posted by DaleDe

4 beeps typically means that the battery has run down completely. Generally recharging the battery will restore operation. It is not recommended to run without a battery installed and it may not even work, I haven't tried it personally.

I charged it overnight twice with no luck.

DaleDe · 09-18-2009, 11:34 AM

Quote:

Originally Posted by SDRebel

I charged it overnight twice with no luck.

As I have told you before in other of the many forums you have posted this problem in that your battery seems to not take a charge or the charger or charging circuit is likely bad.

Dale

SDRebel · 09-18-2009, 12:56 PM

Quote:

Originally Posted by DaleDe

As I have told you before in other of the many forums you have posted this problem in that your battery seems to not take a charge or the charger or charging circuit is likely bad.

Dale

it would make sense except for the following two reasons:
1. Someone else reported the reader working without a battery connected
2. Even if the battery were dead it should still show in the screen that it is charging

you indeed seem to be stalking me and getting rather aggressive as time passes

DaleDe · 09-18-2009, 04:01 PM

Quote:

Originally Posted by SDRebel

it would make sense except for the following two reasons:
1. Someone else reported the reader working without a battery connected
2. Even if the battery were dead it should still show in the screen that it is charging

you indeed seem to be stalking me and getting rather aggressive as time passes

Sorry if you think I am stalking. I was just getting frustrated that every thread seems to be another post of the same subject. Perhaps some others have reported but yours seems to dominate.

Dale

A4- · 09-18-2009, 08:41 PM

Quote:

Originally Posted by DaleDe

As I have told you before in other of the many forums you have posted this problem in that your battery seems to not take a charge or the charger or charging circuit is likely bad.

In a nutshell that is likely to be your problem. It might even be a loose cable/contact.
Li-Ion batteries have a safety cut-off at around 20-25% (zero % reported by device) if it goes below that it has a chance of exploding when being charged. So when a Li-Ion battery get's drained to much, charging it is (for consumers) impossible. For more detailed information about batteries and the best way to treat them see: http://batteryuniversity.com

My advice, just RMA it (as suggested by Astak) and pick up a pbook for a few days

SDRebel · 09-18-2009, 09:55 PM

Quote:

Originally Posted by DaleDe

Sorry if you think I am stalking. I was just getting frustrated that every thread seems to be another post of the same subject. Perhaps some others have reported but yours seems to dominate.

Dale

yes, I do get repetitive with things that frustrate me as much, sorry

SDRebel · 09-18-2009, 09:56 PM

Quote:

Originally Posted by A4-

In a nutshell that is likely to be your problem. It might even be a loose cable/contact.
Li-Ion batteries have a safety cut-off at around 20-25% (zero % reported by device) if it goes below that it has a chance of exploding when being charged. So when a Li-Ion battery get's drained to much, charging it is (for consumers) impossible. For more detailed information about batteries and the best way to treat them see: http://batteryuniversity.com

My advice, just RMA it (as suggested by Astak) and pick up a pbook for a few days

RMAed it is! I actually sent it out yesterday.

09-10-2009, 04:26 PM	#1
MacZap Member Posts: 11 Karma: 12 Join Date: Mar 2008 Device: iLiad, Cybook, Palm T\|X, iPod Touch	Bebook dead - multiple beep Hi all, my Bebook has a problem. When I connect the USB cable to charge the battery, the red LED lighton, then the Bebook plays 5 very fast beeps, and shuts off, totally dead. If I remove the battery, the Bebook boots normally. It sems a battery problem, but even change the battery with another (not new) battery, the problem still remain. Some suggestions? What it means the 5 fast beep at boot? thanks MZ

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
<Command Line> Add multiple books in multiple formats	himitsu	Calibre	8	09-25-2010 11:07 PM
Bug: entries with multiple formats trigger multiple conversions	flinx1	Calibre	12	05-21-2010 06:23 AM
PR-505 vs Bebook mini vs Bebook (5'' vs 6'' screens)	aliettedb	Which one should I buy?	12	02-03-2010 06:28 AM
anyway to turn off the Beep ?	oncdoc	Astak EZReader	4	11-30-2009 08:48 PM
Disastrous firmware upgrade for many BeBook users: no excuses from BeBook!!!	Diogene	BeBook	86	12-10-2008 10:02 AM

09-11-2009, 05:19 AM	#2
Kleki Connoisseur Posts: 58 Karma: 192 Join Date: Mar 2009 Location: Cologne area, Germany Device: Pocketbook Touch HD3 (+ an old Hanlin V3)	I have the same problem sometimes. Here's what to do: 1) Take out the battery 2) Boot with USB cable plugged in 3) Replace the battery (cable still plugged in) 4) Wait 10 minutes Now you should be able to boot without cable again. If not, wait longer in step 4) or try booting with both battery and cable in place. A similar solution is described on the jinke web site. While I always get the book working again it is very annoying when this happens out of reach of my laptop. This is really what keeps me from recommending the Hanlin V3. hth

09-16-2009, 09:31 PM	#3
SDRebel Addict Posts: 294 Karma: 92 Join Date: Aug 2009 Device: astak pro	I have the astak pocket pro (hanlin v5?) and mine is completely dead with four beeps, any idea what could solve it? astak wants me to send it back. Right now i connected it to power without the battery on and still won't boot. I've already tried all the normal stuff.

09-18-2009, 01:49 AM	#4
MacZap Member Posts: 11 Karma: 12 Join Date: Mar 2008 Device: iLiad, Cybook, Palm T\|X, iPod Touch	Thanks Kleki, I got the same solution withouth understanding the process. About the 4 beeps (instead of 5) I never see this problem. Maybe some suggestion is in the Jinke site. Kleki, can you post a link to the Jinke page with this suggestions? Thanks MZ

09-18-2009, 04:22 AM	#5
Kleki Connoisseur Posts: 58 Karma: 192 Join Date: Mar 2009 Location: Cologne area, Germany Device: Pocketbook Touch HD3 (+ an old Hanlin V3)	The solution for the not booting problem is described in the Jinke FAQ, # 5. But I do not see anything related to SDRebel's problem there.

09-18-2009, 10:56 AM	#8
DaleDe Grand Sorcerer Posts: 11,470 Karma: 13095790 Join Date: Aug 2007 Location: Grass Valley, CA Device: EB 1150, EZ Reader, Literati, iPad 2 & Air 2, iPhone 7	4 beeps typically means that the battery has run down completely. Generally recharging the battery will restore operation. It is not recommended to run without a battery installed and it may not even work, I haven't tried it personally.

Advert

Advert