Onyx boox m92 and m96 broken screen

[deleted]

Hello ydoughan,

Sorry for the late reply.

I had success replacing my screen of my m96 with : https://www.aliexpress.com/snapshot/...Id=32732615636

I wasn't sure it was the right model but it worked out OKAY, everything works as it should.

Tip: be careful with the disassembly, the frame is glued in with double-sided sticky tape and if you are not careful you will mangle it when trying to remove.

[Martin H]

Hi, I also have an old M96 with a broken screen. After contacting Onyx in China and reading posts on this forum and others, I decided to have a go at replacing the screen myself.

My M96 has a broken ED097TC1 (LF)-55 screen and I ordered a ED097TC1 (LF)-S1 screen from Shenfa Communication Equipment Co. on Ali Express. I've carefully replaced the screen and the M96 works again, opening .pdf and .doc files stored on it. However, the screen doesn't display properly, with parts of the image duplicated and 'rubbish' on other parts. Then I noticed that the label on the new screen says 'E307459', so I've contacted Shenfa to ask if this is a direct replacement for the ED097TC1 (LF)-S1.

I've also read on this forum that there can be an issue about the 'vcon' setting. The voltage label on the old screen is -1.46 and on the new screen is -1.21. I don't know if it's necessary to adjust the 'vcon' setting. If it is I don't know how to do this. It's mentioned on this forum in old posts, but the links on these posts are broken.

Any help would be greatly appreciated!

[M4H35H]

Originally Posted by Martin H

It's mentioned on this forum in old posts, but the links on these posts are broken.

https://www.dropbox.com/s/ymllr3qxae...DATER.rar?dl=0

Correction: Sorry, the above is for M92. For M96 and M96M, see this page http://opankey.ru/onyx-boox-m96m-zeus-keyboard for mfgtool2.

[Rubensosa]

Originally Posted by Martin H

Hi, I also have an old M96 with a broken screen. After contacting Onyx in China and reading posts on this forum and others, I decided to have a go at replacing the screen myself.

My M96 has a broken ED097TC1 (LF)-55 screen and I ordered a ED097TC1 (LF)-S1 screen from Shenfa Communication Equipment Co. on Ali Express. I've carefully replaced the screen and the M96 works again, opening .pdf and .doc files stored on it. However, the screen doesn't display properly, with parts of the image duplicated and 'rubbish' on other parts. Then I noticed that the label on the new screen says 'E307459', so I've contacted Shenfa to ask if this is a direct replacement for the ED097TC1 (LF)-S1.

I've also read on this forum that there can be an issue about the 'vcon' setting. The voltage label on the old screen is -1.46 and on the new screen is -1.21. I don't know if it's necessary to adjust the 'vcon' setting. If it is I don't know how to do this. It's mentioned on this forum in old posts, but the links on these posts are broken.

Any help would be greatly appreciated!

I have the same problem. Can I solve it by entering the signature specified by user M4H35 with mfgtools?
thank you

[Rubensosa]

Originally Posted by Rubensosa

I have the same problem. Can I solve it by entering the signature specified by user M4H35 with mfgtools?
thank you

Resolved

whit update mfgtools

[Rubensosa]

where can I buy the joystick for boox m96, because it is broken

[Rubensosa]

Originally Posted by Rubensosa

where can I buy the joystick for boox m96, because it is broken

resolved......

[M4H35H]

Originally Posted by Rubensosa

resolved......

Where did you buy it?