Nia 306a doesn't boot

le_stauss · 02-16-2025, 05:57 AM

Hi,
I have recently take this tab from trash.
The screen flash every approx 2 minutes, the led blink.

It's a 4A2 version

The sd card inside, looks good on computer, but the system file may be corrupted.

I try inkbox, on another card that have (4gB) but verification with balena was failed.

With the stock sdcard

Code:

U-Boot 2016.03-00069-g0d2ab3e0d5 (Nov 27 2019 - 15:15:57 +0800)

CPU:   Freescale i.MX6ULL rev1.1 at 396MHz
CPU:   Commercial temperature grade (0C to 95C) at 26C
Reset cause: POR
Board: MX6ULL NTX
I2C:   ready
DRAM:  256 MiB
force_idle_bus: sda=0 scl=0 sda.gp=0x15 scl.gp=0x14
MMC:   board_mmc_init() : isd=1 
FSL_SDHC: 0, FSL_SDHC: 1
In:    serial
Out:   serial
Err:   serial
ntx_hw_early_init() 0
ram p=80000000,size=268435456
switch to partitions #0, OK
mmc0 is current device
mmc read 0x8ffffe00 0x3ff 0x1

MMC read: dev # 0, block # 1023, count 1 ... 1 blocks read: OK
mmc read 0x8ffffe00 0x400 0x1

MMC read: dev # 0, block # 1024, count 1 ... 1 blocks read: OK
RC5T619_watchdog(1,32)
ntx_hw_late_init()
mmc read 0x8ffffc00 0x1 0x1

MMC read: dev # 0, block # 1, count 1 ... 1 blocks read: OK
NTXSN not avalible !
ntx_gpio_init():R [ERROR] GPIO group number error (0)!!
ntx_gpio_init():B [ERROR] GPIO group number error (0)!!
ntx_gpio_get_value(404) : error parameter ! null ptr !
ntx_config_fastboot_layout():10 binaries partition added
ntx_config_fastboot_layout():3 mbr partition added
fuse bank 0 offset 3 is 0x5C310044
check_and_clean: reg 0, flag_set 0
Fastboot: Normal
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
mmc read 0x80800000 0x800 0x2c00

MMC read: dev # 0, block # 2048, count 11264 ... 11264 blocks read: OK
Booting from mmc ...
mmc read 0x83000000 0x505 0x1

MMC read: dev # 0, block # 1285, count 1 ... 1 blocks read: OK
dtb size = 41589@83000000
mmc read 0x83000000 0x506 0x57

MMC read: dev # 0, block # 1286, count 87 ... 87 blocks read: OK

 hwcfgp=8ffffe00,pcb=81,customer=9

ntx_gpio_get_value(404) : error parameter ! null ptr !
ESDin=0,UPGKey=-1,PWRKey=0,USBin=0x0,BootESD=0,MenuKey=0
mmc read 0x8ffffc00 0x37ff 0x1

MMC read: dev # 0, block # 14335, count 1 ... 1 blocks read: OK
mmc read 0x8ff71a00 0x3800 0x472

MMC read: dev # 0, block # 14336, count 1138 ... 1138 blocks read: OK
mmc read 0x8ff71800 0x405 0x1

MMC read: dev # 0, block # 1029, count 1 ... 1 blocks read: OK
[WARNING] Binaries load sequence should Lo->Hi !
mmc read 0x8ff71600 0x406 0x2

MMC read: dev # 0, block # 1030, count 2 ... 2 blocks read: OK
Kernel RAM visiable size=255M->255M
ntx_gpio_init():R [ERROR] GPIO group number error (0)!!
ntx_gpio_init():B [ERROR] GPIO group number error (0)!!
hwcfg rootfstype : 2
ntx_prebootm : cmd=setenv bootargs ${bootargs}  hwcfg_p=0x8ffffe00 hwcfg_sz=110 waveform_p=0x8ff71a00 waveform_sz=582529 ntxfw_p=0x8ff71600 ntxfw_sz=782 mem=255M boot_port=1 rootfstype=ext4 quiet
Kernel image @ 0x80800000 [ 0x000000 - 0x4819a0 ]
## Flattened Device Tree blob at 83000000
   Booting using the fdt blob at 0x83000000
   Using Device Tree in place at 83000000, end 8300d274

Starting kernel ...

/cpus/cpu@0 missing clock-frequency property
sy7636-pmic sy7636-pmic: request vcom gpio failed (-16)!
sy7636-pmic sy7636-pmic: request powerup gpio failed (-16)!
syscon-poweroff 20cc000.snvs:snvs-poweroff: pm_power_off already claimed 80021934 ntx_machine_poweroff
PMU: ricoh61x_battery_probe : version is RICOH61x_BATTERY_VERSION: 2014.02.21 V3.1.0.0-Solution1 2015/02/09
==== calc_soc_by_voltageMethod E60U22 ====
imx6ul-pinctrl 2290000.iomuxc-snvs: pin MX6ULL_PAD_SNVS_TAMPER3 already requested by 21f8000.i2c; cannot claim for gpio-keys
imx6ul-pinctrl 2290000.iomuxc-snvs: pin-5 (gpio-keys) status -22
imx6ul-pinctrl 2290000.iomuxc-snvs: could not request pin 5 (MX6ULL_PAD_SNVS_TAMPER3) from group gpio_snvs_keys_grp  on device 2290000.iomuxc-snvs
gpio-keys gpio-keys: Error applying setting, reverse things back
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
blk_update_request: I/O error, dev mmcblk0, sector 835655
Buffer I/O error on dev mmcblk0p2, logical block 131107, lost async page write
blk_update_request: I/O error, dev mmcblk0, sector 835657
Buffer I/O error on dev mmcblk0p2, logical block 131108, lost async page write
blk_update_request: I/O error, dev mmcblk0, sector 835659
Buffer I/O error on dev mmcblk0p2, logical block 131109, lost async page write
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
blk_update_request: I/O error, dev mmcblk0, sector 573443
Buffer I/O error on dev mmcblk0p2, logical block 1, lost async page write
blk_update_request: I/O error, dev mmcblk0, sector 573445
Buffer I/O error on dev mmcblk0p2, logical block 2, lost async page write
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
blk_update_request: I/O error, dev mmcblk0, sector 573959
Buffer I/O error on dev mmcblk0p2, logical block 259, lost async page write
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
blk_update_request: I/O error, dev mmcblk0, sector 573993
Buffer I/O error on dev mmcblk0p2, logical block 276, lost async page write
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
blk_update_request: I/O error, dev mmcblk0, sector 574059
Buffer I/O error on dev mmcblk0p2, logical block 309, lost async page write
blk_update_request: I/O error, dev mmcblk0, sector 574061
Buffer I/O error on dev mmcblk0p2, logical block 310, lost async page write
blk_update_request: I/O error, dev mmcblk0, sector 574063
Buffer I/O error on dev mmcblk0p2, logical block 311, lost async page write
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sendimmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
mmcblk0: card_busy_detect: error sending status cmd, status 0x80900
EXT4-fs (mmcblk0p2): error loading journal
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,2)
---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,2)

With inkbox fw (and maybe corrupted good writing image) :

Code:

U-Boot 2016.03-inkbox (Jun 20 2023 - 20:40:34 +0000)

CPU:   Freescale i.MX6ULL rev1.1 at 396MHz
CPU:   Commercial temperature grade (0C to 95C) at 27C
Reset cause: POR
Board: MX6ULL NTX
I2C:   ready
DRAM:  256 MiB
force_idle_bus: sda=0 scl=0 sda.gp=0x15 scl.gp=0x14
MMC:   board_mmc_init() : isd=1 
FSL_SDHC: 0, FSL_SDHC: 1
In:    serial
Out:   serial
Err:   serial
ntx_hw_early_init() 0
ram p=80000000,size=268435456
switch to partitions #0, OK
mmc0 is current device
mmc read 0x8ffffe00 0x3ff 0x1

MMC read: dev # 0, block # 1023, count 1 ... 1 blocks read: OK
mmc read 0x8ffffe00 0x400 0x1

MMC read: dev # 0, block # 1024, count 1 ... 1 blocks read: OK
RC5T619_watchdog(1,32)
ntx_hw_late_init()
mmc read 0x8ffffc00 0x1 0x1

MMC read: dev # 0, block # 1, count 1 ... 1 blocks read: OK
NTXSN not avalible !
ntx_gpio_init():R [ERROR] GPIO group number error (0)!!
ntx_gpio_init():B [ERROR] GPIO group number error (0)!!
ntx_gpio_get_value(404) : error parameter ! null ptr !
ntx_config_fastboot_layout():10 binaries partition added
ntx_config_fastboot_layout():3 mbr partition added
fuse bank 0 offset 3 is 0x5C310044
check_and_clean: reg 0, flag_set 0
Fastboot: Normal
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
mmc read 0x80800000 0x14000 0x5000

MMC read: dev # 0, block # 81920, count 20480 ... 20480 blocks read: OK
Booting from mmc ...
mmc read 0x83000000 0x505 0x1

MMC read: dev # 0, block # 1285, count 1 ... 1 blocks read: OK
dtb size = 41589@83000000
mmc read 0x83000000 0x506 0x57

MMC read: dev # 0, block # 1286, count 87 ... 87 blocks read: OK

 hwcfgp=8ffffe00,pcb=81,customer=9

ntx_gpio_get_value(404) : error parameter ! null ptr !
ESDin=0,UPGKey=-1,PWRKey=0,USBin=0x0,BootESD=0,MenuKey=0
mmc read 0x8ffffc00 0x37ff 0x1

MMC read: dev # 0, block # 14335, count 1 ... 1 blocks read: OK
binary magic @ sector no. 14336 not found !
"waveform" not exist !!
mmc read 0x8ffffc00 0x405 0x1

MMC read: dev # 0, block # 1029, count 1 ... 1 blocks read: OK
mmc read 0x8ffff800 0x406 0x3

MMC read: dev # 0, block # 1030, count 3 ... 3 blocks read: OK
Kernel RAM visiable size=255M->255M
ntx_gpio_init():R [ERROR] GPIO group number error (0)!!
ntx_gpio_init():B [ERROR] GPIO group number error (0)!!
hwcfg rootfstype : 2
hwcfg partition type : 2,bootmode=0
ntx_prebootm : cmd=setenv bootargs ${bootargs}  hwcfg_p=0x8ffffe00 hwcfg_sz=110 ntxfw_p=0x8ffff800 ntxfw_sz=1034 mem=255M boot_port=1 rootfstype=ext4 root=/dev/mmcblk0p1 quiet
Bad Linux ARM zImage magic!
RC5T619_watchdog(0,0)
eBR-1A # <00>

For my knowlegde :
could you explain me what mean ntx_gpio ? what is ntx ?

thank you

le_stauss · Yesterday, 03:06 PM

Hi all,
For news :

So ntx mean the name of the plateform (cpu mainboard)

My tab, have not hardware problem, sdcard system file was corrupted.

So with forumer help, I grab a stock firmware on another sdcard and the tab boot and is now fully functiunal.

thank you so much.

Bye

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
PRS-T1 Doesn't boot my reader.	Nabuccoo	Sony Reader	10	01-21-2014 07:53 PM
903 Pocketbook doesn't go beyond boot screen	avg_user	PocketBook	6	12-20-2011 09:31 AM
iLiad My Iliad doesn't boot	miguel.ossa	iRex	1	08-14-2010 12:21 PM

Yesterday, 03:06 PM	#2
le_stauss Junior Member Posts: 3 Karma: 10 Join Date: Feb 2025 Device: Kobo Nia	Hi all, For news : So ntx mean the name of the plateform (cpu mainboard) My tab, have not hardware problem, sdcard system file was corrupted. So with forumer help, I grab a stock firmware on another sdcard and the tab boot and is now fully functiunal. thank you so much. Bye

Advert