Register Guidelines E-Books Search Today's Posts Mark Forums Read

Go Back   MobileRead Forums > E-Book Readers > Amazon Kindle > Kindle Developer's Corner

Notices

Reply
 
Thread Tools Search this Thread
Old 06-05-2018, 10:11 PM   #1
rvwc
Junior Member
rvwc began at the beginning.
 
rvwc's Avatar
 
Posts: 1
Karma: 10
Join Date: Jun 2018
Device: PW2
PW2 Hangs During Boot

Stopped booting, so I soldered up a serial connection.

[ 14.918988] mmc0: Timeout, intmask=0x00100002
[ 14.925862] mmcblk0: error -110 transferring data, sector 945154, nr 2, cmd response 0x900, card status 0xd00
[ 14.937370] end_request: I/O error, dev mmcblk0, sector 945154
[ 14.943231] Buffer I/O error on device mmcblk0p3, logical block 15873
[ 20.377726] mmc0: Timeout, intmask=0x00100002


On the second boot in the log I entered the recovery menu to see what options are available. What should my next steps be?

Code:
U-Boot 2009.08-lab126 (Jul 02 2017 - 01:45:38)

CPU: Freescale i.MX6 family TO0.0 at 996 MHz
Temperature:   37 C, calibration data 0x5855065f
mx6sl pll1: 996MHz
mx6sl pll2: 528MHz
mx6sl pll3: 480MHz
mx6sl pll8: 50MHz
ipg clock     : 66000000Hz
ipg per clock : 66000000Hz
uart clock    : 80000000Hz
cspi clock    : 60000000Hz
ahb clock     : 132000000Hz
axi clock   : 198000000Hz
emi_slow clock: 22000000Hz
ddr clock     : 396000000Hz
usdhc1 clock  : 198000000Hz
usdhc2 clock  : 198000000Hz
usdhc3 clock  : 198000000Hz
usdhc4 clock  : 198000000Hz
MMC:  FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2
Board: Pinot WFO
Boot Reason: [ POR ]
Boot Device: NAND
Board Id: 0272201145030Q2Q
S/N: 90172201451505XB
I2C:   ready
DRAM:  256 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Quick Memory Test 0x80000000, 0xfff0000
POST done in 57 ms
Battery voltage: 4089 mV

Hit any key to stop autoboot:  0 
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   Linux-3.0.35-lab126
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2920540 Bytes =  2.8 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

[    0.097489] boot: C def:bcut:batterycut=1
[    0.274649] LPDDR2 MfgId: 0x1 [Samsung]
[    0.278512] 
[    0.278514] just text: vaddr c0129f3c, va 0xc0129200 pa 0x801000c3 attr 0x6
[    0.291160] 
[    0.291163] nmx6sl_wfi_iram: vaddr d084e000, va 0xd084e200 pa 0x904043 attr 0x2
[    0.300004] 
[    0.300007] mx6sl_ddr: vaddr d0856000, va 0xd0856200 pa 0x905043 attr 0x2
[    0.308404] 
[    0.308406] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149
[    0.319179] 
[    0.319181] ANATOP: vaddr f40c8000, va 0xf40c8200 pa 0x20110c3 attr 0x149
[    0.333529] 
[    0.333531] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149
[    0.345662] 
[    0.345664] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149
[    0.356015] 
[    0.356018] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149
[    0.365904] 
[    0.365906] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149
DEBUG:recovery-util.c:1570:setup_die_signals():Installed signal handlers.
3.0.35-lab126 #2 PREEMPT Sun Jul 2 01:50:33 PDT 2017 armv7l
Press [ENTER] for recovery menu...       0 //dev/mmcblk0p4:
CHS=4/16/104512 size=3424649216 bytes
flag type      first       last  lba first   lba size
Partition p1:
0x00 0x0b         16 <large>            16    6688752
    CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
BOOTING DEFAULT.
IP-Config: no devices to configure
kinit: Mounted root (ext3 filesystem) readonly.
info sytem:mounted_proc::
info system:mounted_sys::
info system:sy00::
info system:mounted_dev::
info milestone:6.80:49.1:
info milestone:6.83:49.2:
info milestone:6.86:49.3:
info milestone:6.91:49.4:
info milestone:6.95:49.5:
info sytem:mounted_tmpfs::
info milestone:7.03:sy50:
info system:start:time=7060:
info hardware:no_wan::WiFi only device. No WAN found
info system:config:platform=wario,board=pinot,rev=34,proto=Y,wifi=Y,wan=N:
info milestone:7.27:sy51:
lipc-send-event[843]: W def:lipc:method=LipcOpenEx service=com.lab126.hal:Method has been deprecated.
lipc-send-event[844]: W def:lipc:method=LipcOpenEx service=com.lab126.hal:Method has been deprecated.
lipc-send-event[843]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[844]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[843]: C def:dbusi::Failed to init dbus
lipc-send-event[844]: C def:dbusi::Failed to init dbus
lipc-send-event[843]: E def:open::Failed to open LIPC
lipc-send-event[844]: E def:open::Failed to open LIPC
lipc-send-event[843]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
lipc-send-event[844]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
info milestone:8.29:sy99:
info system:done:time=8320:
crond[886]: crond: crond (busybox 1.17.1) started, log level 8
init.exe: sshd main process (884) terminated with status 2
init.exe: sshd mai process endedini?.exe: recevent pre-start procinfo system_fs_loopbacks:mountingfs:Mounting compressed directories filesystem images:
warn system_fs_loopbacks:mountpointmissing:Image /lib/firmware/cyttsp.sqsh not mounted, non existing mounting point:
info system_fs_loopbacks:mounted:Image /usr/share/X11/xkb.sqsh mounted:
info system_fs_loopbacks:mounted:Image /usr/java/lib/fonts.sqsh mounted:
info system_fs_loopbacks:mounted:Image /etc/kdb.src.sqsh mounted:
info system_fs_loopbacks:mounted:Image /usr/lib/locale.sqsh mounted:
info system_fs_loopbacks:mounted:Image /usr/share/keyboard.sqsh mounted:
info system_fs_loopbacks:mounted:Image /opt/var/local.sqsh mounted:
info system:emiting_event:mounted_fs_loopbacks:
debug sytem:event_emitted:mounted_fs_loopbacks:
info milestone:9.04:fs75:
info system:emiting_event:loaded_modules_dependencies:
debug sytem:event_emitted:loaded_modules_dependencies:
info modules:modprobe:loading module fsl_otg_arc:
info system:emiting_event:loaded_fsl_otg_arc:
debug sytem:event_emitted:loaded_fsl_otg_arc:
info modules:modprobe:loading module ehci_hcd:
info system:emiting_event:loaded_ehci_hcd:
debug sytem:event_emitted:loaded_ehci_hcd:
info modules:modprobe:loading module fuse:
info system:emiting_event:loaded_fuse:
debug sytem:event_emitted:loaded_fuse:
info hardware:no_wan::WiFi only device. No WAN found
info milestone:9.36:fs00:
info system:emiting_event:loaded_ppp_async:
debug sytem:event_emitted:loaded_ppp_async:
info system:emiting_event:loaded_fakekey:
debug sytem:event_emitted:loaded_fakekey:

[   14.918988] mmc0: Timeout, intmask=0x00100002
[   14.925862] mmcblk0: error -110 transferring data, sector 945154, nr 2, cmd response 0x900, card status 0xd00
[   14.937370] end_request: I/O error, dev mmcblk0, sector 945154
[   14.943231] Buffer I/O error on device mmcblk0p3, logical block 15873
[   20.377726] mmc0: Timeout, intmask=0x00100002
[   66.515794] bcut: C def:pcut:wario pending 15 second battery cut:





?HW


U-Boot 2009.08-lab126 (Jul 02 2017 - 01:45:38)

CPU: Freescale i.MX6 family TO0.0 at 996 MHz
Temperature:   39 C, calibration data 0x5855065f
mx6sl pll1: 996MHz
mx6sl pll2: 528MHz
mx6sl pll3: 480MHz
mx6sl pll8: 50MHz
ipg clock     : 66000000Hz
ipg per clock : 66000000Hz
uart clock    : 80000000Hz
cspi clock    : 60000000Hz
ahb clock     : 132000000Hz
axi clock   : 198000000Hz
emi_slow clock: 22000000Hz
ddr clock     : 396000000Hz
usdhc1 clock  : 198000000Hz
usdhc2 clock  : 198000000Hz
usdhc3 clock  : 198000000Hz
usdhc4 clock  : 198000000Hz
MMC:  FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2
Board: Pinot WFO
Boot Reason: [ POR ]
Boot Device: NAND
Board Id: 0272201145030Q2Q
S/N: 90172201451505XB
I2C:   ready
DRAM:  256 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Quick Memory Test 0x80000000, 0xfff0000
POST done in 57 ms
Battery voltage: 4122 mV

Hit any key to stop autoboot:  0 
## Booting kernel from Legacy Image at 80800000 ...
   Image Name:   Linux-3.0.35-lab126
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2920540 Bytes =  2.8 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

[    0.097500] boot: C def:bcut:batterycut=1
[    0.274524] LPDDR2 MfgId: 0x1 [Samsung]
[    0.278699] 
[    0.278703] just text: vaddr c0129f3c, va 0xc0129200 pa 0x801000c3 attr 0x6
[    0.291133] 
[    0.291136] nmx6sl_wfi_iram: vaddr d084e000, va 0xd084e200 pa 0x904043 attr 0x2
[    0.299974] 
[    0.299977] mx6sl_ddr: vaddr d0856000, va 0xd0856200 pa 0x905043 attr 0x2
[    0.308307] 
[    0.308309] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149
[    0.319079] 
[    0.319082] ANATOP: vaddr f40c8000, va 0xf40c8200 pa 0x20110c3 attr 0x149
[    0.333496] 
[    0.333498] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149
[    0.345582] 
[    0.345584] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149
[    0.355953] 
[    0.355955] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149
[    0.365903] 
[    0.365905] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149
DEBUG:recovery-util.c:1570:setup_die_signals():Installed signal handlers.
3.0.35-lab126 #2 PREEMPT Sun Jul 2 01:50:33 PDT 2017 armv7l
Press [ENTER] for recovery menu...       0 /

Charge: 100% [##########################################################]


Menu
====
3. Load MMC0 over USB storage
4. Erase MMC0
I. Initialize Partition Table (fdisk) and format FAT
O. Format and overwrite FAT partition
E. Export FAT partition
U. Update using update*.bin file on FAT partition
M. Update using update*.bin file on FAT partition of second MMC port
D. dmesg / kernel printk ring buffer.
Q. quit
Choose:  10 /

Charge: 100% [##########################################################]


Menu
====
3. Load MMC0 over USB storage
4. Erase MMC0
I. Initialize Partition Table (fdisk) and format FAT
O. Format and overwrite FAT partition
E. Export FAT partition
U. Update using update*.bin file on FAT partition
M. Update using update*.bin file on FAT partition of second MMC port
D. dmesg / kernel printk ring buffer.
Q. quit
Choose:   1 -
Menu timeout
BOOTING DEFAULT.
IP-Config: no devices to configure
kinit: Mounted root (ext3 filesystem) readonly.
info sytem:mounted_proc::
info system:mounted_sys::
info system:sy00::
info system:mounted_dev::
info milestone:17.40:49.1:
info milestone:17.43:49.2:
info milestone:17.46:49.3:
info milestone:17.51:49.4:
info milestone:17.55:49.5:
info sytem:mounted_tmpfs::
info milestone:17.63:sy50:
info system:start:time=17660:
info hardware:no_wan::WiFi only device. No WAN found
info system:config:platform=wario,board=pinot,rev=34,proto=Y,wifi=Y,wan=N:
info milestone:17.87:sy51:
lipc-send-event[840]: W def:lipc:method=LipcOpenEx service=com.lab126.hal:Method has been deprecated.
lipc-send-event[839]: W def:lipc:method=LipcOpenEx service=com.lab126.hal:Method has been deprecated.
lipc-send-event[839]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[839]: C def:dbusi::Failed to init dbus
lipc-send-event[839]: E def:open::Failed to open LIPC
lipc-send-event[839]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
lipc-send-event[840]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[840]: C def:dbusi::Failed to init dbus
lipc-send-event[840]: E def:open::Failed to open LIPC
lipc-send-event[840]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
info milestone:18.78:sy99:
info system:done:time=18810:
crond[856]: crond: crond (busybox 1.17.1) started, log level 8
ini?.exe: sshd main process (854)init.exe: sshd main process ended, resp?wning
init.exe: recevent pre-start process (859) terminated with status 1
info system_fs_loopbacks:mountingfs:Mounting compressed directories filesystem images:
warn system_fs_loopbacks:mountpointmissing:Image /lib/firmware/cyttsp.sqsh not mounted, non existing mounting point:
info system_fs_loopbacks:mounted:Image /usr/share/X11/xkb.sqsh mounted:
info system_fs_loopbacks:mounted:Image /usr/java/lib/fonts.sqsh mounted:
info system_fs_loopbacks:mounted:Image /etc/kdb.src.sqsh mounted:
info system_fs_loopbacks:mounted:Image /usr/lib/locale.sqsh mounted:
info system_fs_loopbacks:mounted:Image /usr/share/keyboard.sqsh mounted:
info system_fs_loopbacks:mounted:Image /opt/var/local.sqsh mounted:
info system:emiting_event:mounted_fs_loopbacks:
debug sytem:event_emitted:mounted_fs_loopbacks:
info milestone:19.50:fs75:
info system:emiting_event:loaded_modules_dependencies:
debug sytem:event_emitted:loaded_modules_dependencies:
info modules:modprobe:loading module fsl_otg_arc:
info system:emiting_event:loaded_fsl_otg_arc:
debug sytem:event_emitted:loaded_fsl_otg_arc:
info modules:modprobe:loading module ehci_hcd:
info system:emiting_event:loaded_ehci_hcd:
debug sytem:event_emitted:loaded_ehci_hcd:
info modules:modprobe:loading module fuse:
info system:emiting_event:loaded_fuse:
debug sytem:event_emitted:loaded_fuse:
info hardware:no_wan::WiFi only device. No WAN found
info system:emiting_event:loaded_ppp_async:
info milestone:19.66:fs00:
debug sytem:event_emitted:loaded_ppp_async:
info system:emiting_event:loaded_fakekey:
debug sytem:event_emitted:loaded_fakekey:

[   25.215074] mmc0: Timeout, intmask=0x00100002
[   25.221613] mmcblk0: error -110 transferring data, sector 945154, nr 2, cmd response 0x900, card status 0xd00
[   25.233408] end_request: I/O error, dev mmcblk0, sector 945154
[   25.239271] Buffer I/O error on device mmcblk0p3, logical block 15873
[   30.677718] mmc0: Timeout, intmask=0x00100002
[  240.164570] INFO: task mount:1004 blocked for more than 120 seconds.
[  240.170928] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  240.181581] waiters_print:98
[  360.184578] INFO: task mount:1004 blocked for more than 120 seconds.
[  360.190936] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  360.201567] waiters_print:98
[  480.204577] INFO: task mount:1004 blocked for more than 120 seconds.
[  480.210935] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  480.221580] waiters_print:98
[  600.224578] INFO: task mount:1004 blocked for more than 120 seconds.
[  600.230936] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  600.241573] waiters_print:98
[  720.244578] INFO: task mount:1004 blocked for more than 120 seconds.
[  720.250937] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  720.261630] waiters_print:98
[  840.264577] INFO: task mount:1004 blocked for more than 120 seconds.
[  840.270935] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  840.281538] waiters_print:98
[  960.284570] INFO: task mount:1004 blocked for more than 120 seconds.
[  960.290928] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  960.301595] waiters_print:98
[ 1080.304573] INFO: task mount:1004 blocked for more than 120 seconds.
[ 1080.310930] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1080.321536] waiters_print:98
[ 1080.332063] INFO: task sh:1013 blocked for more than 120 seconds.
[ 1080.339753] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1080.349739] waiters_print:98
[ 1200.344570] INFO: task mount:1004 blocked for more than 120 seconds.
[ 1200.350928] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1200.361572] waiters_print:98
rvwc is offline   Reply With Quote
Advert
Old 06-06-2018, 09:42 AM   #2
knc1
Analog Forever!
knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.
 
knc1's Avatar
 
Posts: 16,133
Karma: 17256900
Join Date: Feb 2012
Location: Central Texas
Device: No K1, PW2, KV, KOA
Replace the eMMC (flash memory) chip.
Those memory error messages mean just what they say.

We have a thread here on how-to do the memory chip change, but if you don't have access to a hot air, SMD re-work station and tools;
You now have a used PW2 display for sale.
knc1 is offline   Reply With Quote
Old 06-06-2018, 09:53 AM   #3
ilovejedd
hopeless n00b
ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.
 
ilovejedd's Avatar
 
Posts: 2,755
Karma: 7279194
Join Date: Jan 2009
Location: in the middle of nowhere
Device: Paperwhite 3, iPad 9.7, iPad 12.9
Quote:
Originally Posted by knc1 View Post
Replace the eMMC (flash memory) chip.
Those memory error messages mean just what they say.

We have a thread here on how-to do the memory chip change, but if you don't have access to a hot air, SMD re-work station and tools;
You now have a used PW2 display for sale.
Interesting. Wonder how common eMMC failure is on e-ink readers.

I've seen plenty of NAND failures on flash drives (PortableApps can be quite heavy on those). Haven't seen one on a mobile device until now. Makes me appreciate the internal microSD slot on the Kobo.

Last edited by ilovejedd; 06-06-2018 at 09:55 AM.
ilovejedd is offline   Reply With Quote
Old 06-06-2018, 02:22 PM   #4
knc1
Analog Forever!
knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.knc1 ought to be getting tired of karma fortunes by now.
 
knc1's Avatar
 
Posts: 16,133
Karma: 17256900
Join Date: Feb 2012
Location: Central Texas
Device: No K1, PW2, KV, KOA
Often enough that we have an example thread posted by someone who did the replacement.

The recovery process, after the hardware replacement, is only slightly more complex than recovering from "Erase All".

And the backup script I posted creates backups of all the required items (if run prior to the failure of course - so run it now and keep the set of files it creates).
knc1 is offline   Reply With Quote
Old 06-06-2018, 07:43 PM   #5
ilovejedd
hopeless n00b
ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.ilovejedd ought to be getting tired of karma fortunes by now.
 
ilovejedd's Avatar
 
Posts: 2,755
Karma: 7279194
Join Date: Jan 2009
Location: in the middle of nowhere
Device: Paperwhite 3, iPad 9.7, iPad 12.9
Quote:
Originally Posted by knc1 View Post
Often enough that we have an example thread posted by someone who did the replacement.

The recovery process, after the hardware replacement, is only slightly more complex than recovering from "Erase All".

And the backup script I posted creates backups of all the required items (if run prior to the failure of course - so run it now and keep the set of files it creates).
Nah, way beyond my skill set. Simpler to just buy a new device (and I've got some spares at the moment).
ilovejedd is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Aura KA1 - Factory Reset Hangs at Boot gravdev Kobo Reader 10 09-09-2017 10:27 AM
902 PB 902 Hangs on. Boot problems. Xisco PocketBook 11 12-06-2011 04:55 AM
When Wifi is turned off an android process hangs after boot. kenjennings enTourage Archive 1 09-03-2010 11:18 AM
iLiad hangs at the boot stage haihaowu iRex 5 09-22-2009 01:26 PM
iLiad hangs on boot - Reflash / Format doesn't help oakinger iRex 12 09-05-2008 04:12 AM


All times are GMT -4. The time now is 11:36 PM.


MobileRead.com is a privately owned, operated and funded community.