02-05-2013, 06:51 PM | #76 |
Junior Member
Posts: 5
Karma: 11128
Join Date: Jan 2013
Device: Kindle DXGizlle
|
Make sure you set the hyperterminal settings correctly via the directions. Make sure you can connect via a com port and you have the baud rate set correctly. I have no idea if you fried it or note, I only used a 1.8v which I knew would work.
|
02-05-2013, 11:55 PM | #77 | |
Junior Member
Posts: 2
Karma: 10
Join Date: Feb 2013
Device: kindle dx
|
Quote:
But I tried this link. It's died - that's a reason of my request here. |
|
02-06-2013, 01:13 AM | #78 |
Junior Member
Posts: 5
Karma: 10
Join Date: Jan 2013
Device: Kindle DX
|
wanted to thank you guys for your posts on the forum and any guides you made, got my dx up and running after a day of learning the ins and outs of Ubuntu!
I followed Yifan Lu's debricking guide and with a little help from McQuackers My DX is up and running! For the record I used this Serial Connector : http://www.mouser.com/ProductDetail/...252bb/GLoFR6IZ Connected from the headphone jack to the left: 4. Black (grnd) 3. Yellow (RXD) 2. Orange (TXD) Also I would like to note that If I ever find myself doing this again I will invest in a soldering iron. |
02-06-2013, 07:00 AM | #79 | |
The Grand Mouse 高貴的老鼠
Posts: 71,556
Karma: 306214458
Join Date: Jul 2007
Location: Norfolk, England
Device: Kindle Voyage
|
Quote:
seems to work fine for me. Here it is as a live link. |
|
02-16-2013, 09:01 AM | #80 |
Junior Member
Posts: 4
Karma: 16516
Join Date: Feb 2013
Device: Kindle dx
|
Help with dxg undemoing
Hi progress has been made.My usb adapter was junk.I ordered a real serial adapter with the max 232 chip,Put on a 3v external power,I am reading the characters in the windows terminal.However I cannot send files.in Uboot I tried to send files It says no response from the remote system.Anybody have an idea or a workaround?Thanks
|
02-16-2013, 10:19 AM | #81 | |
Going Viral
Posts: 17,212
Karma: 18210809
Join Date: Feb 2012
Location: Central Texas
Device: No K1, PW2, KV, KOA
|
Quote:
|
|
02-20-2013, 11:38 PM | #82 |
Junior Member
Posts: 2
Karma: 10
Join Date: Sep 2007
Device: Kindle Touch, DXG
|
Anybody knows where to order a serial adapter with 1.8 volts?
|
02-21-2013, 01:00 PM | #83 |
( ͡° ͜ʖ ͡°){ʇlnɐɟ ƃǝs}Týr
Posts: 6,586
Karma: 6299991
Join Date: Jun 2012
Location: uti gratia usura (Yao ying da ying; Mo ying da yieng)
Device: PW-WIFI|K5-3G+WIFI| K4|K3-3G|DXG|K2| Rooted Nook Touch
|
Get a https://www.mobileread.com/forums/sho...7&postcount=68
1.8v remember... check the voltage. but seriously - I just read back this thread to get these links??? (its only 6 pages) maybe do a bit of hunting yourself seek and ye shall find. Last edited by twobob; 04-03-2013 at 02:10 PM. |
03-05-2013, 10:44 AM | #84 |
Junior Member
Posts: 4
Karma: 16516
Join Date: Feb 2013
Device: Kindle dx
|
You don't need 1.8v adapter for DXG.
I used this method https://www.mobileread.com/forums/showthread.php?t=49942 For power I used 1.5v,3v,5v. Two AA bateries .Worked best with 3v.The adapter in e bay is 2$ .Hyperterminal in windows xp works best.Theoretically you might not even need the adapter.If you have the password you might login from kindle developer menu,and be able to see the 4 partitions in linux I cannot confirm this because I don't want to brick my kindle again.In the end my serial console was acting out but it might have been because I changed the hyperterminal program . |
03-06-2013, 02:42 AM | #85 |
Wizard
Posts: 1,379
Karma: 2155307
Join Date: Nov 2010
Location: Goettingen, Germany
Device: Kindle Paperwhite, Kobo Mini
|
Warning: If you don't really know what you are doing, don't always expect to succeed. In this case: Be prepared to break your DXG. 3 Volts is above the voltage used and may always break the device. I really, really consider this bad advice.
That said, well, it didn't break for you. Of course it worked best with 3 volts. That's due to the operational specifications for your typical MAX232, which are at 5 volts. For 3 Volts there's the MAX3232. For 1.8V, typically a ttl voltage converter is needed. Everything else is a dirty hack, so be prepared to pay the price (a high one in case of a KDX, if you ask me). Purely singular-evidence based advice like this is a bit out of place here, I think. And please, don't follow the suggestion to use no adapter at all. 9 volts differential signals are not what a typical SoC will tolerate. You have been warned. Also note that RX and TX are two different matters when you go over voltage. If your adapter is tolerant, it might still receive data from the Kindle when it has long fried the receiver on the Kindle by transmitting with too high voltage. |
03-29-2013, 11:25 PM | #86 |
Junior Member
Posts: 4
Karma: 16516
Join Date: Feb 2013
Device: Kindle dx
|
hawhill is right.I am telling from my experience.The voltage in Tx Rx was 2.8v when I measured and everybody here talks about 1.8v.As I said you might not need the adapter you need an usb cable and the instructions here.https://www.mobileread.com/forums/sho...0&postcount=25
When you hit 3 do it from the developers menu alt+E=3 give password and continue from usb in Linux.Maybe I am wrong as I typed from the hyperterminal in the serial adapter but I think I understand the process now.I followed this instructions and was success.In the end I ended up spending the same money as buying a used one in Craig list buy the fun it was worth it. |
04-03-2013, 01:56 PM | #87 |
Junior Member
Posts: 5
Karma: 10000
Join Date: Nov 2010
Device: Kindle Voyage, Kindle Paperwhite
|
can the DXG demo still able to register with amazon.com? I read the image is blacklisted and it can no longer be registered with amazon.com
|
04-03-2013, 02:39 PM | #88 |
Going Viral
Posts: 17,212
Karma: 18210809
Join Date: Feb 2012
Location: Central Texas
Device: No K1, PW2, KV, KOA
|
|
06-03-2013, 07:27 AM | #89 |
Junior Member
Posts: 5
Karma: 10
Join Date: May 2013
Device: none
|
please!
Can somebody share dump of DXG?
|
06-03-2013, 09:08 AM | #90 | |
Going Viral
Posts: 17,212
Karma: 18210809
Join Date: Feb 2012
Location: Central Texas
Device: No K1, PW2, KV, KOA
|
Quote:
The owner of that image, removed it from our collections (rightly so) and followed the legal process in his country to get his own DX re-registered by Amazon. The process described in this thread duplicates the storage area in the DX that contains both the owner and the device specific information. Which was just fine for the original poster - since the O.P. owned the original DX the information was cloned from. The only suggestion that can be made here is to use the image files that you create yourself from a DX device that you already own. Try buying one with a broken screen (cheap, since the screen is most of the price), use that firmware to create your own un-demo image files. Last edited by knc1; 06-03-2013 at 09:11 AM. |
|
Tags |
debricking |
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Got a Demo Kindle (k5) from work, need to remove demo software. | Stea1th | Kindle Developer's Corner | 71 | 09-02-2014 02:46 PM |
I demo'd a K4 | Fbone | Amazon Kindle | 26 | 11-01-2011 07:11 PM |
Demo: Jetbook mini official demo | bookwarm | Ectaco jetBook | 36 | 09-21-2010 12:18 PM |
Help - I need a demo! | tlighty | Which one should I buy? | 1 | 11-05-2007 02:43 PM |