New firmware - Page 4

wallcraft · 09-04-2009, 12:42 PM

Quote:

Originally Posted by jwsheets

Is this firmware for the 5" or 6" device? I went to the EZReader site and I don't see a new firmware release.

It is for the 6" Hanlin V3, and is currently only at astak.com (http://www.astak.com/download/Astak_..._10_090109.rar).

slayda · 09-07-2009, 01:00 PM

Quote:

Originally Posted by JSWolf

Well, the hyperlink bug should never have happened in the first place. That's just beyond poor QA.

Somewhat like the RTF bug with Sony's 500 not supporting TOCs or images. But since it was Sony, it seemed like I was the only one who complained about it.

wallcraft · 09-07-2009, 06:10 PM

I have just tried the 2009-09-01 EZ Reader Basic firmware. It does fix two ePub problems: a) page number was getting bigger as the font size was made larger, and b) images were getting larger (bigger than the sceen) as the font size was increased. As was said previously, it does not add hyperlink support to ePubs. It also replaces the original 5 ePub fonts sizes with 4 font sizes. The new smallest font size is even smaller than before, the 2nd font is the same as the original smallest font, and the largest font (the 4th font) is now smaller than the 2nd font size previously. In my opinion, the fonts are now much too small.

I don't know why getting the fonts right is so hard. Sony has 5 font sizes for its PRS-700 and PRS-600, and Sony ebook library shows these sizes on a Windows PC or a Mac. See the attached screenshots. The largest on the Sony is about the original Jinke 4th size and the smallest on the Sony is about the new Jinke 3rd size. The Sony font sizes may not be optimal, but they are better than the Hanlin options so far.

cvkemp · 09-07-2009, 06:35 PM

I have not figured that out either; I would suggest giving the user the control and letting us set a percentage for the fonts. But I have to say the epubs that I have created by converting them using calibre looks much better than when you buy a epub that has DRM.

Chuck

GA Russell · 09-07-2009, 06:40 PM

Does this, or will it, have any relevance to the Pocket Pro?

Lbooker · 09-07-2009, 06:50 PM

Quote:

Originally Posted by wallcraft

I have just tried the 2009-09-01 EZ Reader Basic firmware. It does fix two ePub problems: a) page number was getting bigger as the font size was made larger, and b) images were getting larger (bigger than the sceen) as the font size was increased. As was said previously, it does not add hyperlink support to ePubs. It also replaces the original 5 ePub fonts sizes with 4 font sizes. The new smallest font size is even smaller than before, the 2nd font is the same as the original smallest font, and the largest font (the 4th font) is now smaller than the 2nd font size previously. In my opinion, the fonts are now much too small.

I don't know why getting the fonts right is so hard. Sony has 5 font sizes for its PRS-700 and PRS-600, and Sony ebook library shows these sizes on a Windows PC or a Mac. See the attached screenshots. The largest on the Sony is about the original Jinke 4th size and the smallest on the Sony is about the new Jinke 3rd size. The Sony font sizes may not be optimal, but they are better than the Hanlin options so far.

Three of the Sony font sizes look too big for normal eyes. I tried a pdf file with this latest Astak firmware and the font sizes were the same as in the other recent firmwares from other vendors. I did not try epub. But I tend to disagree with you: I want more font sizes between size 1 and size 2. They should give people the choice between at least ten font sizes, to make everybody happy.

wallcraft · 09-07-2009, 07:02 PM

I also tried the PDF on the new firmware. The PDF font sizes have changed, but not as much as the ePub font sizes. Now font size 4 is the old font size 3, and font size 5 is smaller than the old font size 4. I did not have much problem with the original PDF sizes, which were better than the ePub sizes, but the new ones are ok. I would prefer the largest size to be the same as the old 4 but otherwise this is good.

I agree, though, that a lot of these issues would go away if there were 8 font sizes.

phenomshel · 09-08-2009, 02:20 AM

I just upgraded the firmware. Saw no improvement at all on font sizes for pdf's, nor any improvement with reflow. I must admit I'm disappointed.

emellaich · 09-08-2009, 02:44 AM

Quote:

Originally Posted by wallcraft

I have just tried the 2009-09-01 EZ Reader Basic firmware. It does fix two ePub problems: a) page number was getting bigger as the font size was made larger, and b) images were getting larger (bigger than the sceen) as the font size was increased. As was said previously, it does not add hyperlink support to ePubs. It also replaces the original 5 ePub fonts sizes with 4 font sizes. The new smallest font size is even smaller than before, the 2nd font is the same as the original smallest font, and the largest font (the 4th font) is now smaller than the 2nd font size previously. In my opinion, the fonts are now much too small.

I don't know why getting the fonts right is so hard. Sony has 5 font sizes for its PRS-700 and PRS-600, and Sony ebook library shows these sizes on a Windows PC or a Mac. See the attached screenshots. The largest on the Sony is about the original Jinke 4th size and the smallest on the Sony is about the new Jinke 3rd size. The Sony font sizes may not be optimal, but they are better than the Hanlin options so far.

Wallcraft, I'm guessing that the problem may be related to another discovery of yours. You noted that a given size is fixed in the number of pixels not in the actual measured size. I believe that Jinke uses the same firmware for the ppro and the V3. This means that a font that is perfect for the V3 would be 20 percent too small on the V5. As a result, I think they are trying to jigger the set of fonts so that it covers an acceptable range on both readers.

MLH

emellaich · 09-08-2009, 02:50 AM

Don't know if all of you folks are keeping track of the Hanlin thread, but the very latest version of the Bebook firmware includes a search function. Hopefully this will migrate to the Astak version soon.
https://www.mobileread.com/forums/showthread.php?t=55884

MLH

DaleDe · 09-08-2009, 01:38 PM

Quote:

Originally Posted by wallcraft

I have just tried the 2009-09-01 EZ Reader Basic firmware. It does fix two ePub problems: a) page number was getting bigger as the font size was made larger, and b) images were getting larger (bigger than the sceen) as the font size was increased. As was said previously, it does not add hyperlink support to ePubs. It also replaces the original 5 ePub fonts sizes with 4 font sizes. The new smallest font size is even smaller than before, the 2nd font is the same as the original smallest font, and the largest font (the 4th font) is now smaller than the 2nd font size previously. In my opinion, the fonts are now much too small.

I don't know why getting the fonts right is so hard. Sony has 5 font sizes for its PRS-700 and PRS-600, and Sony ebook library shows these sizes on a Windows PC or a Mac. See the attached screenshots. The largest on the Sony is about the original Jinke 4th size and the smallest on the Sony is about the new Jinke 3rd size. The Sony font sizes may not be optimal, but they are better than the Hanlin options so far.

I agree, they go from one extreme to the other. Why can't they find a middle ground. This looks like something that Astak may have don't themselves as it is not released on the Jinke site. I have noticed a similar release of the Bebook so perhaps it is a trial balloon. I haven't tried the bebook one to see if it is as bad.

Dale

DaleDe · 09-08-2009, 01:41 PM

Quote:

Originally Posted by wallcraft

I also tried the PDF on the new firmware. The PDF font sizes have changed, but not as much as the ePub font sizes. Now font size 4 is the old font size 3, and font size 5 is smaller than the old font size 4. I did not have much problem with the original PDF sizes, which were better than the ePub sizes, but the new ones are ok. I would prefer the largest size to be the same as the old 4 but otherwise this is good.

I agree, though, that a lot of these issues would go away if there were 8 font sizes.

Or provide the ability for the user to specify what 4 sizes they want. There needs to be some consistency between the various readers on the device and have a user specified option that was used by them all would be a plus. Every format works differently now.

Dale

JSWolf · 09-12-2009, 12:51 AM

Unless the body font is specified in a specific size, what you get from increasing the size will be based on the size as defined in the ePub. Given what I've read in another thread it sounds like 150% is very much needed.

09-07-2009, 06:10 PM	#48
wallcraft reader Posts: 6,977 Karma: 5183568 Join Date: Mar 2006 Location: Mississippi, USA Device: Kindle 3, Kobo Glo HD	I have just tried the 2009-09-01 EZ Reader Basic firmware. It does fix two ePub problems: a) page number was getting bigger as the font size was made larger, and b) images were getting larger (bigger than the sceen) as the font size was increased. As was said previously, it does not add hyperlink support to ePubs. It also replaces the original 5 ePub fonts sizes with 4 font sizes. The new smallest font size is even smaller than before, the 2nd font is the same as the original smallest font, and the largest font (the 4th font) is now smaller than the 2nd font size previously. In my opinion, the fonts are now much too small. I don't know why getting the fonts right is so hard. Sony has 5 font sizes for its PRS-700 and PRS-600, and Sony ebook library shows these sizes on a Windows PC or a Mac. See the attached screenshots. The largest on the Sony is about the original Jinke 4th size and the smallest on the Sony is about the new Jinke 3rd size. The Sony font sizes may not be optimal, but they are better than the Hanlin options so far. Attached Thumbnails

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Firmware Update Instructions and the latest Firmware Versions	mitchwah	Ectaco jetBook	113	10-24-2023 10:02 PM
What I would like to see, regarding firmware	griffonwing	News	4	12-23-2009 11:42 PM
SMARTQ7: firmware 5 VS .92 firmware 5.1?	wwang	Alternative Devices	2	12-17-2009 01:41 PM
What I would like in firmware v1.2	beschuit	Bookeen	51	06-23-2008 07:12 AM
Firmware	col	Sony Reader	11	06-18-2007 11:11 AM

09-07-2009, 06:35 PM	#49
cvkemp Loving life Posts: 1,431 Karma: 7991496 Join Date: Mar 2009 Location: Hot Springs Village, Arkansas Device: PaperWhite 6 SE, Fire HD8	I have not figured that out either; I would suggest giving the user the control and letting us set a percentage for the fonts. But I have to say the epubs that I have created by converting them using calibre looks much better than when you buy a epub that has DRM. Chuck

09-07-2009, 06:40 PM	#50
GA Russell Ticats/Als, Riders/Lions Posts: 7,717 Karma: 31487351 Join Date: Aug 2009 Location: Raleigh, NC Device: Paperwhite, Kindles 10 & 4 and jetBook Lite	Does this, or will it, have any relevance to the Pocket Pro?

09-07-2009, 07:02 PM	#52
wallcraft reader Posts: 6,977 Karma: 5183568 Join Date: Mar 2006 Location: Mississippi, USA Device: Kindle 3, Kobo Glo HD	I also tried the PDF on the new firmware. The PDF font sizes have changed, but not as much as the ePub font sizes. Now font size 4 is the old font size 3, and font size 5 is smaller than the old font size 4. I did not have much problem with the original PDF sizes, which were better than the ePub sizes, but the new ones are ok. I would prefer the largest size to be the same as the old 4 but otherwise this is good. I agree, though, that a lot of these issues would go away if there were 8 font sizes.

09-08-2009, 02:20 AM	#53
phenomshel ZCD BombShel Posts: 4,793 Karma: 8293322 Join Date: Jan 2009 Location: The Frozen North (aka Illinois, USA) Device: iPad, STB Kindle Oasis	I just upgraded the firmware. Saw no improvement at all on font sizes for pdf's, nor any improvement with reflow. I must admit I'm disappointed.

09-08-2009, 02:50 AM	#55
emellaich Wizard Posts: 1,101 Karma: 4388403 Join Date: Oct 2007 Device: Palm>Ebookman>IPaq>Axim>Cybook>Kndl2>IPAD>Kndl3SO>Voyager>Oasis	Don't know if all of you folks are keeping track of the Hanlin thread, but the very latest version of the Bebook firmware includes a search function. Hopefully this will migrate to the Astak version soon. https://www.mobileread.com/forums/showthread.php?t=55884 MLH

09-12-2009, 12:51 AM	#58
JSWolf Resident Curmudgeon Posts: 80,782 Karma: 150249619 Join Date: Nov 2006 Location: Roslindale, Massachusetts Device: Kobo Libra 2, Kobo Aura H2O, PRS-650, PRS-T1, nook STR, PW3	Unless the body font is specified in a specific size, what you get from increasing the size will be based on the size as defined in the ePub. Given what I've read in another thread it sounds like 150% is very much needed.