Register Guidelines E-Books Search Today's Posts Mark Forums Read

Go Back   MobileRead Forums > E-Book Readers > Sony Reader

Notices

Reply
 
Thread Tools Search this Thread
Old 11-11-2026, 10:31 PM   #1
pratjic
Junior Member
pratjic began at the beginning.
 
Posts: 1
Karma: 10
Join Date: Nov 2026
Device: Prs-350
[Request] 3D scan or exact measurements of Sony PRS-350 / PRS-650 stylus for 3D print

Hi everyone,
Since finding an original replacement stylus for the Sony Reader PRS-350 (and PRS-650, as they share the exact same stylus) is nearly impossible nowadays, I’m planning to model and 3D print one myself.
If anyone still has the original stylus and an iPhone/iPad (or just a ruler/calipers), could you please help me out with either of the following?
1. A quick 3D scan (Photogrammetry / Object Capture):Note: Rear LiDAR alone isn't detailed enough for such a thin object, so Photo/Object mode works much better. Free apps like 3d Scanner App (by Laan Labs) or Scaniverse allow free .STL or .OBJ export without a subscription. Tip: Please place the stylus next to a ruler or a coin on a matte, textured surface (like a wooden table) so I can calibrate the exact 1:1 scale.
2. Or simple reference photos + measurements:Top-down and side-profile photos of the stylus lying flat next to a ruler (to minimize lens distortion, please take the photo from a bit further away and zoom in), plus exact total length, shaft diameter, and clip/latch dimensions (ideally measured with calipers).
Important details I need to get right for a snug fit in the reader's slot:
Shape and thickness of the top clip/cap that locks into the housing.
Any small grooves, notches, or tapering along the body that hold it in place.
Once I clean up the mesh and test-print a working version, I’ll gladly share the final .STL file here for the community!
You can post it here or send the files/photos directly to my email: pratjic@gmail.com
Thanks a lot in advance!❤️
pratjic is offline   Reply With Quote
Old Today, 10:22 AM   #2
Divingduck
Wizard
Divingduck ought to be getting tired of karma fortunes by now.Divingduck ought to be getting tired of karma fortunes by now.Divingduck ought to be getting tired of karma fortunes by now.Divingduck ought to be getting tired of karma fortunes by now.Divingduck ought to be getting tired of karma fortunes by now.Divingduck ought to be getting tired of karma fortunes by now.Divingduck ought to be getting tired of karma fortunes by now.Divingduck ought to be getting tired of karma fortunes by now.Divingduck ought to be getting tired of karma fortunes by now.Divingduck ought to be getting tired of karma fortunes by now.Divingduck ought to be getting tired of karma fortunes by now.
 
Posts: 1,167
Karma: 1410083
Join Date: Nov 2010
Location: Germany
Device: Sony PRS-650
Maybe this one is sufficient for you: https://www.printables.com/model/491...r-sony-prs-650
Divingduck is online now   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Sony PRS-350 Stylus repair KNI Sony Reader 7 06-17-2016 03:17 AM
Sony PRS 650 vs PRS 350 CPU yoanna Sony Reader Dev Corner 0 04-25-2012 03:09 PM
Sony PRS-350 and PRS-650 thymaster Sony Reader 68 09-17-2010 11:44 PM


All times are GMT -4. The time now is 01:12 PM.


MobileRead.com is a privately owned, operated and funded community.