Help Needed: Tolino Vision 6 - MicroSD Card Image and Instructions

[Flux]

Hello Waldy, my Vision´s 6 SD card is defect. Mainboard is 37NB-E70P1M+6B2. Could you please send me the required image file? Regarding the size of the SD card: I don´t have a new SD card yet. Thanks in advance! Would be awesome if it works. Greetings from Germany!

[Waldy]

Hi,
PM send.

[Yda454]

Hi Waldy,

I have a Tolino Vision 6 that does not boot. The device is detected on my PC in Allwinner FEL mode, and after opening it I found that the internal microSD card is completely missing.

My mainboard is 37NB-E70P1M+6B2.

Could you please send me the correct microSD card image for this board revision?

Thank you very much for your help!

[Waldy]

Hi,
PM send.

[Off3line]

Hi Waldy

I am also in dire need of a clean image for my e reader Tolino Vision 6.


I found the following serial nr on my mainboard: 37NB-E70P1M+6B2

Thank you so much!

[Waldy]

Hi,
PM sent.

[VladShmi]

Originally Posted by Waldy

Hi,
PM sent.

Hi Waldy
Can I get the image for the Tolino Vision 6, 6B2 variant?

PM already enabled

[Waldy]

Hi,
PM sent.

[Exil]

Hello Waldy,
I have a Tolino Vision 6 with a damaged internal microSD card.

Mainboard: 37NB-E70P1M+6B2

I have already replaced the microSD card with a new SanDisk 32 GB, but cloning my damaged original card did not boot. The device is detected in Allwinner FEL mode (USB VID 1F3A / PID EFE8).

Could you please send me the full microSD image for the 6B2 board?

I already have the TV6_recovery_E70P14_15.2.6.img recovery file, but I am looking for the complete SD-card image.

Thank you very much for your help!

[torsten1]

Hi Waldy,
I am the next one with an broken SD card.
Could you please send me the inage for an toplino vison 6?
Thank you very much
Torsten

[THEXSX]

Hi, i would like to request an SD-Card Image for my Tolino Vision 6 6C1, Thanks.

[envesion]

Hi Waldy,
Could you please send me the SD card image for the Tolino Vision 6 as well?
Thank you very much.

[Ahornbaum]

Hi Waldy,

looks like I am not the only one with a damaged µSD card in a Tolino Vision 6.
My Mainboard: 37NB-E70P1M+6C1

Can you please send me a link to the image, if you have one?

Thank you very much.

[ufg.seidlm]

Hi Waldy,

my Tolino Vision 6 stopped booting right after the latest official firmware update. The LED blinks, but the screen stays frozen and I can't get into recovery mode (tried power + lower page button several times).

The original SD card is still readable, so I made a full raw image and wrote it to a new SanDisk Extreme 32GB (U3, A1) with balenaEtcher. The partition layout is identical. With the new card the device behaves exactly like with the original one: LED blinks, but no boot and no recovery menu. So I guess the system itself was damaged by the update.

Device details:
- Mainboard: 37NB-E70P1M+6B2
- S/N starts with 230...
- OS: Windows 11 (Linux also available)

Could you please send me a clean SD card image for the 6B2 board? PMs are enabled.

Thank you very much for your help!

[Waldy]

Originally Posted by ufg.seidlm

With the new card the device behaves exactly like with the original one: LED blinks, but no boot and no recovery menu.

Hi,
flash the recovery image to the boot partition and perform a "Recover the System" operation.

Details:

Install the ADB/Fastboot drivers on Windows 11.

Connect your Tolino Vision 6 to your computer using a USB cable.
Power off the device completely (press and hold the power button for approximately 10–15 seconds).

Press and hold both the bottom page-turn button (assuming the grip area is on the right) and the power button simultaneously until your computer detects a new device (usually takes 4–6 seconds).
Then, run the following:
1--FASTBOOT__TEST.bat
2---FLASH_recovery-to-boot-TV6-6B2.bat

The device will boot into recovery mode.
Select "Recover the System."
The device will revert to firmware version 15.0.0.
Update the firmware to version 16.2.2, then perform a factory reset via the Tolino settings menu.

This should resolve the issue, if it doesn't, I have sent the necessary images to you via private message.