Problems updating Firmware

Janelle · 07-31-2009, 09:04 PM

Hi,
I recenting bought a HanLin V3 and have been having the most frustrating time updating the firmware.
I always get stuck on the "Checking update data please wait" screen. It never progresses further than that regardless of the 4 different SD cards I have used. I have also tried formatting them all with the Panasonic SD formatter that I saw recommended somewhere on these forums as well.
My question is, is there some trick to getting it to work? Am I holding in the V+ and power buttons too long or not long enough?? I usually hear two beeps and let the buttons go.
I have redownloaded the file multiple times with different web browsers and from different sources with always the same results!!
I am at my wits end about now. I am new to ebook readers and gathered from reading these forums that I can use other types of firmware. (I think Open Inkpot was one.) Would this help me and can I ruin anything using these??
Sorry for the longwinded post. Thanks in advance for any help that's provided.

Musicman · 07-31-2009, 09:18 PM

Check the name of the firmware file - it should be V3update.bin.

If it is not, then rename it.

Janelle · 07-31-2009, 09:41 PM

Thanks for your help Musicman, unfortunately that doesn't seem to be the problem as it is correctly named.
I think I might try downloading again in the hopes that it will work for me this time.

wallcraft · 07-31-2009, 09:57 PM

I suggest looking at OpenInkpot 0.2 Installation Guide and Restoring original firmware from OpenInkPot.

A 1 GB SD card is best, although others might work.

Your update procedure sounds right. The other thing is to make sure the battery is fully charged. You could also try attaching the USB charger for the update (although I have never tried this, it is recommended by Jinke). If this works, then most likely you have a sub-par battery. This is the most common problem with the Hanlin.

For a list, of firmware sites see EZReader Firmware. I like the Feb 25 LBook firmware (or OpenInkPot).

Janelle · 08-01-2009, 02:37 AM

Thanks for your help wallcraft. I have tried your suggestions regarding the battery and size of the SD card but no joy.
Maybe I will just not worry about it for now and get through some of the books I have waiting to be read!!
Thanks again for all of your help!

vdevan · 08-01-2009, 06:41 AM

Hi:
One of the most important thing for updating your firmware is to ensure that you have an SD card that is either 1GB or smaller than 1GB. I had similar problems with 2GB SD card. As soon as swapped it with 1 GB card, it worked perfectly well.
Hope this helps

leismom · 08-09-2009, 06:28 PM

I have an Astak EZReader (6") that I've had since Nov. 08, and have had similar problems when trying to update the firmware. The firmware update seems to go along fine until it gets to "Update Resource" and then just stops or hangs. The light is red. I am using a <1 GB SD card. It is also plugged into the USB power adapter so the battery doesn't interfere. Still, no good update and if I stop it, the reader just tries to boot up, gets to the logo and can't go any further. Any ideas.

keng2000 · 08-10-2009, 10:08 AM

Quote:

Originally Posted by leismom

I have an Astak EZReader (6") that I've had since Nov. 08, and have had similar problems when trying to update the firmware. The firmware update seems to go along fine until it gets to "Update Resource" and then just stops or hangs. The light is red. I am using a <1 GB SD card. It is also plugged into the USB power adapter so the battery doesn't interfere. Still, no good update and if I stop it, the reader just tries to boot up, gets to the logo and can't go any further. Any ideas.

Turn on your device and press "OK" immediately.
You may see some message then try to upgrade firmware again.
This may help...

07-31-2009, 09:04 PM	#1
Janelle Junior Member Posts: 3 Karma: 10 Join Date: Jul 2009 Device: HanLin V3	Problems updating Firmware Hi, I recenting bought a HanLin V3 and have been having the most frustrating time updating the firmware. I always get stuck on the "Checking update data please wait" screen. It never progresses further than that regardless of the 4 different SD cards I have used. I have also tried formatting them all with the Panasonic SD formatter that I saw recommended somewhere on these forums as well. My question is, is there some trick to getting it to work? Am I holding in the V+ and power buttons too long or not long enough?? I usually hear two beeps and let the buttons go. I have redownloaded the file multiple times with different web browsers and from different sources with always the same results!! I am at my wits end about now. I am new to ebook readers and gathered from reading these forums that I can use other types of firmware. (I think Open Inkpot was one.) Would this help me and can I ruin anything using these?? Sorry for the longwinded post. Thanks in advance for any help that's provided.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Firmware Update Please help on updating K2 firmware from 2.3 to 2.5	PS Kindle	Amazon Kindle	13	01-21-2011 11:49 AM
Problems updating to 0.6.30	kojak666	Calibre	4	12-27-2009 07:13 PM
Firmware Update Problems Updating to Newest Firmware	Dr. Wily	Amazon Kindle	12	12-04-2009 06:10 PM
Firmware Update Updating an unregistered K2 Firmware	kindlethai	Amazon Kindle	2	05-24-2009 06:34 AM
Problems after updating connect software	Zevs	Sony Reader	16	10-28-2007 06:14 PM

07-31-2009, 09:18 PM	#2
Musicman Evangelist Posts: 451 Karma: 364 Join Date: May 2009 Location: New York Device: EZ-Reader - Samsung Nook's- Nook S/T w/Glow - Kindle Fire - Nova 2	Check the name of the firmware file - it should be V3update.bin. If it is not, then rename it.

07-31-2009, 09:41 PM	#3
Janelle Junior Member Posts: 3 Karma: 10 Join Date: Jul 2009 Device: HanLin V3	Thanks for your help Musicman, unfortunately that doesn't seem to be the problem as it is correctly named. I think I might try downloading again in the hopes that it will work for me this time.

07-31-2009, 09:57 PM	#4
wallcraft reader Posts: 6,977 Karma: 5183568 Join Date: Mar 2006 Location: Mississippi, USA Device: Kindle 3, Kobo Glo HD	I suggest looking at OpenInkpot 0.2 Installation Guide and Restoring original firmware from OpenInkPot. A 1 GB SD card is best, although others might work. Your update procedure sounds right. The other thing is to make sure the battery is fully charged. You could also try attaching the USB charger for the update (although I have never tried this, it is recommended by Jinke). If this works, then most likely you have a sub-par battery. This is the most common problem with the Hanlin. For a list, of firmware sites see EZReader Firmware. I like the Feb 25 LBook firmware (or OpenInkPot).

08-01-2009, 02:37 AM	#5
Janelle Junior Member Posts: 3 Karma: 10 Join Date: Jul 2009 Device: HanLin V3	Thanks for your help wallcraft. I have tried your suggestions regarding the battery and size of the SD card but no joy. Maybe I will just not worry about it for now and get through some of the books I have waiting to be read!! Thanks again for all of your help!

08-01-2009, 06:41 AM	#6
vdevan Member Posts: 13 Karma: 14 Join Date: Jul 2009 Device: BEBook	Hi: One of the most important thing for updating your firmware is to ensure that you have an SD card that is either 1GB or smaller than 1GB. I had similar problems with 2GB SD card. As soon as swapped it with 1 GB card, it worked perfectly well. Hope this helps

08-09-2009, 06:28 PM	#7
leismom Ebook Believer Posts: 1 Karma: 10 Join Date: Aug 2009 Location: Bay Area, Northern California Device: EZReader V3	I have an Astak EZReader (6") that I've had since Nov. 08, and have had similar problems when trying to update the firmware. The firmware update seems to go along fine until it gets to "Update Resource" and then just stops or hangs. The light is red. I am using a <1 GB SD card. It is also plugged into the USB power adapter so the battery doesn't interfere. Still, no good update and if I stop it, the reader just tries to boot up, gets to the logo and can't go any further. Any ideas.

Advert

Advert