brick (bootloop) please help pw3

04-04-2020, 08:56 AM	#1
thoriki Member Posts: 17 Karma: 26 Join Date: Jan 2020 Device: kindle paperwhite 7th, and 10th	brick (bootloop) please help pw3 hi, please who can help me, have boot loop. i try use fastboot in bist, and consale say all time "battery voltage: xxxx mV ( "X" is numbers) my loop is this Spoiler: U-Boot 2009.08-lab126 (Nov 15 2019 - 00:11:26) CPU: Freescale i.MX6 family TO0.0 at 996 MHz Temperature: 38 C, calibration data 0x59b5125f mx6sl pll1: 996MHz mx6sl pll2: 528MHz mx6sl pll3: 480MHz mx6sl pll8: 50MHz ipg clock : 66000000Hz ipg per clock : 24000000Hz uart clock : 80000000Hz cspi clock : 60000000Hz ahb clock : 132000000Hz axi clock : 198000000Hz emi_slow clock: 22000000Hz ddr clock : 396000000Hz usdhc1 clock : 198000000Hz usdhc2 clock : 198000000Hz usdhc3 clock : 198000000Hz usdhc4 clock : 198000000Hz MMC: FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2 Board: Muscat WFO Boot Reason: [ POR ] Boot Device: NAND Board Id: 06703091630701WD S/N: G090G105631306JW I2C: ready DRAM: 512 MB Using default environment In: serial Out: serial Err: serial Quick Memory Test 0x80000000, 0x1fff0000 POST done in 111 ms Battery voltage: 3780 mV Hit any key to stop autoboot: 0 ## Booting kernel from Legacy Image at 80800000 ... Image Name: Linux-3.0.35-lab126 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3047788 Bytes = 2.9 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.096485] boot: C def:bcut:batterycut=1 [ 0.101240] [ 0.276144] LPDDR2 MfgId: 0x1 [Samsung] [ 0.280004] [ 0.280006] just text: vaddr c014cffc, va 0xc014c200 pa 0x801000c3 attr 0x6 [ 0.292584] [ 0.292587] nmx6sl_wfi_iram: vaddr e084e000, va 0xe084e200 pa 0x904043 attr 0x2 [ 0.301430] [ 0.301432] mx6sl_ddr: vaddr e0856000, va 0xe0856200 pa 0x905043 attr 0x2 [ 0.309767] [ 0.309769] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149 [ 0.320603] [ 0.320606] ANATOP: vaddr f40c8000, va 0xf40c8200 pa 0x20110c3 attr 0x149 [ 0.334896] [ 0.334899] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149 [ 0.343078] [ 0.343080] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149 [ 0.355562] [ 0.355565] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149 [ 0.365343] [ 0.365345] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149 3.0.35-lab126 #2 PREEMPT Fri Nov 15 00:20:46 UTC 2019 armv7l [ 1.753654] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] [ 1.760933] Regulator Fault Occurred! Retrying powerup... [ 1.838194] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] [ 1.845459] Regulator Fault Occurred! Retrying powerup... [ 1.918148] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] [ 1.925411] Regulator Fault Occurred! Retrying powerup... [ 1.947612] imx_epdc_fb imx_epdc_fb: EPDC powerup timeout/error. [ 2.006940] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] [ 2.014176] Regulator Fault Occurred! Retrying powerup... [ 2.088213] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] [ 2.095474] Regulator Fault Occurred! Retrying powerup... [ 2.168200] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] [ 2.175461] Regulator Fault Occurred! Retrying powerup... [ 2.197553] imx_epdc_fb imx_epdc_fb: EPDC powerup timeout/error. [ 2.256894] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] [ 2.264130] Regulator Fault Occurred! Retrying powerup... [ 2.338230] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] [ 2.345492] Regulator Fault Occurred! Retrying powerup... [ 2.418261] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] [ 2.425523] Regulator Fault Occurred! Retrying powerup... [ 2.447602] imx_epdc_fb imx_epdc_fb: EPDC powerup timeout/error. [ 2.453638] imx_epdc_fb imx_epdc_fb: Failed to do initialization sequence -901 === kernel printk buffer (26298 bytes) === <5>[ 0.000000] Linux version 3.0.35-lab126 (builder@eink-builds) (gcc version 4.9.1 (GCC) ) #2 PREEMPT Fri Nov 15 00:20:46 UTC 2019 <4>[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d <4>[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache <4>[ 0.000000] Machine: Freescale i.MX 6SoloLite based Wario Board <6>[ 0.000000] Will try to place printk log at 8fff0000 <4>[ 0.000000] Memory policy: ECC disabled, Data cache writeback <6>[ 0.000000] CPU identified as i.MX6SoloLite, unknown revision <7>[ 0.000000] On node 0 totalpages: 131072 <7>[ 0.000000] free_area_init_node: node 0, pgdat c05da450, node_mem_map c2000000 <7>[ 0.000000] DMA zone: 64 pages used for memmap <7>[ 0.000000] DMA zone: 0 pages reserved <7>[ 0.000000] DMA zone: 8128 pages, LIFO batch:0 <7>[ 0.000000] Normal zone: 960 pages used for memmap <7>[ 0.000000] Normal zone: 121920 pages, LIFO batch:31 <7>[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=132768 <7>[ 0.000000] pcpu-alloc: [0] 0 <4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 <5>[ 0.000000] Kernel command line: rootwait log_pos_goal=0x8fff0000 console=ttymxc0,115200 root=/dev/mmcblk0p1 ro ip=off quiet video=mxcepdcfb:E60,bpp=8,x_mem=3M <4>[ 0.000000] Prink buffer will be relocated to physical address: 8fff0000 <6>[ 0.000000] log_buf_len: 32768 <6>[ 0.000000] early log buf free: 31352(95%) <6>[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) <6>[ 0.000000] Memory: 512MB = 512MB total <5>[ 0.000000] Memory: 513508k/513508k available, 10780k reserved, 0K highmem <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) <5>[ 0.000000] DMA : 0xfde00000 - 0xffe00000 ( 32 MB) <5>[ 0.000000] vmalloc : 0xe0800000 - 0xf2000000 ( 280 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) <5>[ 0.000000] .init : 0xc0008000 - 0xc0138000 (1216 kB) <5>[ 0.000000] .text : 0xc0138000 - 0xc05a3000 (4524 kB) <5>[ 0.000000] .data : 0xc05a4000 - 0xc05e1838 ( 247 kB) <5>[ 0.000000] .bss : 0xc05e185c - 0xc0608260 ( 155 kB) <6>[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] Preemptible hierarchical RCU implementation. <6>[ 0.000000] Verbose stalled-CPUs detection is disabled. <6>[ 0.000000] NR_IRQS:624 <6>[ 0.000000] MXC GPIO hardware <6>[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms <6>[ 0.000000] arm_max_freq=1GHz <6>[ 0.000000] MXC_Early serial console at MMIO 0x2020000 (options '115200') <6>[ 0.000000] bootconsole [ttymxc0] enabled <6>[ 0.000000] Console: colour dummy device 80x30 <6>[ 0.000242] Calibrating delay loop... 1987.37 BogoMIPS (lpj=9936896) <6>[ 0.060117] pid_max: default: 32768 minimum: 301 <6>[ 0.060318] Mount-cache hash table entries: 512 <6>[ 0.060627] CPU: Testing write buffer coherency: ok <6>[ 0.060758] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available <6>[ 0.066968] print_constraints: dummy: <6>[ 0.067126] NET: Registered protocol family 16 <6>[ 0.071277] print_constraints: vddpu: 725 <--> 1300 mV at 700 mV fast normal <6>[ 0.071573] print_constraints: vddcore: 725 <--> 1300 mV at 1475 mV fast normal <6>[ 0.071865] print_constraints: vddsoc: 725 <--> 1300 mV at 1475 mV fast normal <6>[ 0.072168] print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal <6>[ 0.072499] print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal <6>[ 0.072806] print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal <4>[ 0.074441] LAB126 Board id - 06703091630701WD <6>[ 0.078760] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. <6>[ 0.078771] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step. <6>[ 0.078782] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.078800] L310 cache controller enabled <6>[ 0.078809] l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x02030000, Cache size: 262144 B <6>[ 0.089394] bio: create slab <bio-0> at 0 <6>[ 0.092684] max77696> regulator init <6>[ 0.093631] spi_imx imx6q-ecspi.0: probed <6>[ 0.093996] usbcore: registered new interface driver usbfs <6>[ 0.094122] usbcore: registered new interface driver hub <6>[ 0.094267] usbcore: registered new device driver usb <4>[ 0.096446] Reboot Reason - Metric Framework Reporting <6>[ 0.096461] kernel: kernel_metric_generic,0,counter,event_recorder,erc flags,MR_FRSTRT,1, <6>[ 0.096471] kernel: kernel_metric_generic,0,counter,event_recorder,erc flags,SFT_PRSTRT,1, <4>[ 0.096479] Reboot Reason - Legacy Metric Reporting <3>[ 0.096485] boot: C def:bcut:batterycut=1 <3>[ 0.101240] <6>[ 0.104361] MAX77696 TOPSYS 1.0.0 Installed <6>[ 0.107114] max77696-gpio max77696-gpio.0: gpio#0 -- -- func-0 in <6>[ 0.108603] max77696-gpio max77696-gpio.0: gpio#1 -- -- func--1 in <6>[ 0.110086] max77696-gpio max77696-gpio.0: gpio#3 -- -- func-0 in <6>[ 0.111970] MAX77696 GPIO Driver 1.0.0 Installed <4>[ 0.112901] buck mode: 4 <4>[ 0.113651] buck mode: 4 <6>[ 0.114610] print_constraints: max77696_buck1: 900 <--> 1300 mV at 1250 mV fast normal idle standby <4>[ 0.115164] buck mode: 4 <6>[ 0.116126] print_constraints: max77696_buck1dvs: 600 <--> 1300 mV at 900 mV fast normal idle standby <4>[ 0.116648] buck mode: 4 <4>[ 0.117397] buck mode: 4 <6>[ 0.118353] print_constraints: max77696_buck2: 900 <--> 1300 mV at 1200 mV fast normal idle standby <4>[ 0.118900] buck mode: 4 <6>[ 0.119861] print_constraints: max77696_buck2dvs: 600 <--> 1300 mV at 900 mV fast normal idle standby <6>[ 0.120390] print_constraints: max77696_buck3: 600 <--> 3387 mV at 1300 mV fast normal idle standby <4>[ 0.121159] buck mode: 4 <4>[ 0.121906] buck mode: 4 <6>[ 0.122654] print_constraints: max77696_buck4: 1200 mV fast normal idle standby <4>[ 0.123203] buck mode: 4 <6>[ 0.124161] print_constraints: max77696_buck5: 600 <--> 3387 mV at 1800 mV fast normal idle standby <4>[ 0.124695] buck mode: 2 <6>[ 0.125655] print_constraints: max77696_buck6: 600 <--> 3387 mV at 3200 mV fast normal idle standby <6>[ 0.125693] MAX77696 Buck Regulators Driver 1.0.1 Installed <6>[ 0.126504] print_constraints: max77696_ldo1: 800 <--> 3950 mV at 3300 mV normal idle standby <6>[ 0.127069] print_constraints: max77696_ldo2: 800 <--> 3950 mV at 3000 mV normal idle standby <6>[ 0.127608] print_constraints: max77696_ldo3: 800 <--> 3950 mV at 2500 mV normal idle standby <6>[ 0.128173] print_constraints: max77696_ldo4: 800 <--> 2375 mV at 1800 mV normal idle standby <6>[ 0.128712] print_constraints: max77696_ldo5: 800 <--> 2375 mV at 1800 mV normal idle standby <6>[ 0.129276] print_constraints: max77696_ldo6: 800 <--> 3950 mV at 3200 mV normal idle standby <6>[ 0.129821] print_constraints: max77696_ldo7: 800 <--> 3950 mV at 3200 mV normal idle standby <6>[ 0.130357] print_constraints: max77696_ldo8: 800 <--> 2375 mV at 1100 mV normal idle standby <6>[ 0.131025] print_constraints: max77696_ldo9: 800 <--> 2375 mV at 1100 mV normal idle standby <6>[ 0.131590] print_constraints: max77696_ldo10: 2400 <--> 5550 mV at 5200 mV normal idle standby <6>[ 0.132394] MAX77696 Linear Regulators Driver 1.0.2 Installed <6>[ 0.133021] print_constraints: max77696_lsw1: <6>[ 0.133748] print_constraints: max77696_lsw2: <6>[ 0.134437] print_constraints: max77696_lsw3: <6>[ 0.135131] print_constraints: max77696_lsw4: <6>[ 0.135558] MAX77696 Load Switches Driver 1.0.0 Installed <6>[ 0.136741] print_constraints: max77696-display: <6>[ 0.137503] print_constraints: max77696-vcom: <6>[ 0.137823] print_constraints: max77696-vee: <6>[ 0.138152] print_constraints: max77696-vneg: <6>[ 0.138501] print_constraints: max77696-vpos: <6>[ 0.138816] print_constraints: max77696-vddh: <6>[ 0.139824] <6>[ 0.139827] EPD vreg probe complete! <6>[ 0.140432] print_constraints: max77696_vddq: 240 <--> 984 mV at 600 mV <6>[ 0.140483] MAX77696 LPDDR2 Termination Supply Driver 1.0.1 Installed <6>[ 0.142113] MAX77696 I2C Driver 1.0.0 Installed <6>[ 0.144233] Advanced Linux Sound Architecture Driver Version 1.0.24. <4>[ 0.144817] i2c-core: driver [max17135] using legacy suspend method <4>[ 0.144828] i2c-core: driver [max17135] using legacy resume method <6>[ 0.144857] Switching to clocksource mxc_timer1 <6>[ 0.156173] NET: Registered protocol family 2 <6>[ 0.156255] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) <6>[ 0.156430] TCP established hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.156641] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) <6>[ 0.156781] TCP: Hash tables configured (established 16384 bind 16384) <6>[ 0.156789] TCP reno registered <6>[ 0.156796] UDP hash table entries: 256 (order: 0, 4096 bytes) <6>[ 0.156812] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) <6>[ 0.157057] NET: Registered protocol family 1 <6>[ 0.157239] RPC: Registered named UNIX socket transport module. <6>[ 0.157248] RPC: Registered udp transport module. <6>[ 0.157254] RPC: Registered tcp transport module. <6>[ 0.157260] RPC: Registered tcp NFSv4.1 backchannel transport module. <4>[ 0.163023] etb: probe of etb failed with error -2 <4>[ 0.163309] etm: probe of etm.0 failed with error -2 <6>[ 0.163588] Static Power Management for Freescale i.MX6 <6>[ 0.163598] wait mode is enabled for i.MX6 <6>[ 0.163752] cpaddr = 0 suspend_iram_base=f2900000 <6>[ 0.163794] PM driver module loaded <6>[ 0.164067] IMX usb wakeup probe <7>[ 0.164088] the wakeup pdata is 0xde223640 <6>[ 0.164692] IMX usb wakeup probe <7>[ 0.164710] the wakeup pdata is 0xde223440 <6>[ 0.164864] cpu regulator mode:ldo_bypass <6>[ 0.165300] i.MXC CPU frequency driver <6>[ 0.181490] squashfs: version 4.0 (2009/01/31) Phillip Lougher <6>[ 0.182487] msgmni has been set to 1002 <6>[ 0.182932] io scheduler noop registered <6>[ 0.183012] io scheduler cfq registered (default) <6>[ 0.183467] MAX77696 Backlight Driver 1.0.0 Installed <6>[ 0.184265] imx-sdma imx-sdma: loaded firmware 1.1 <6>[ 0.188767] imx-sdma imx-sdma: initialized <6>[ 0.190650] Serial: IMX driver <6>[ 0.190759] imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX <6>[ 0.190786] console [ttymxc0] enabled, bootconsole disabled <6>[ 0.194581] loop: module loaded <6>[ 0.194833] MAX77696 32kHz Oscillator Driver 1.0.0 Installed <6>[ 0.196141] input: max77696-onkey as /devices/platform/imx-i2c.0/i2c-0/0-003c/max77696-onkey.0/input/input0 <6>[ 0.199347] MAX77696 ONKEY Driver 1.0.0 Installed <7>[ 0.215561] max77696-rtc max77696-rtc.0: read time: <7>[ 0.215575] max77696-rtc max77696-rtc.0: YEAR 00 MONTH 01 DOM 0C DOW 10 HOUR 02 MIN 35 SEC 31 <7>[ 0.215588] max77696-rtc max77696-rtc.0: --> 2000-01-12 Thu 02:53:49 <7>[ 0.216019] max77696-rtc max77696-rtc.0: read alarm0: <7>[ 0.216031] max77696-rtc max77696-rtc.0: YEAR 00 MONTH 01 DOM 05 HOUR 01 MIN 14 SEC 01 <7>[ 0.216042] max77696-rtc max77696-rtc.0: --> 2000-01-05 01:20:01 <6>[ 0.216252] max77696-rtc max77696-rtc.0: rtc core: registered max77696-rtc.0 as rtc0 <7>[ 0.235522] max77696-rtc max77696-rtc.0: read time: <7>[ 0.235534] max77696-rtc max77696-rtc.0: YEAR 00 MONTH 01 DOM 0C DOW 10 HOUR 02 MIN 35 SEC 31 <7>[ 0.235547] max77696-rtc max77696-rtc.0: --> 2000-01-12 Thu 02:53:49 <7>[ 0.235977] max77696-rtc max77696-rtc.0: read alarm1: <7>[ 0.235988] max77696-rtc max77696-rtc.0: YEAR 00 MONTH 01 DOM 01 HOUR 00 MIN 00 SEC 00 <7>[ 0.235998] max77696-rtc max77696-rtc.0: --> 2000-01-01 00:00:00 <6>[ 0.236170] max77696-rtc max77696-rtc.0: rtc core: registered max77696-rtc.1 as rtc1 <7>[ 0.237668] max77696-rtc max77696-rtc.0: 1 minute interrupt: off <7>[ 0.237678] max77696-rtc max77696-rtc.0: 1 second interrupt: off <7>[ 0.255527] max77696-rtc max77696-rtc.0: read time: <7>[ 0.255539] max77696-rtc max77696-rtc.0: YEAR 00 MONTH 01 DOM 0C DOW 10 HOUR 02 MIN 35 SEC 31 <7>[ 0.255551] max77696-rtc max77696-rtc.0: --> 2000-01-12 Thu 02:53:49 <7>[ 0.255562] max77696-rtc max77696-rtc.0: current time ** 2000-01-12 Thu 02:53:49 <6>[ 0.255568] MAX77696 RTC Driver 1.0.2 Installed <6>[ 0.256273] snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc2 <6>[ 0.256457] i2c /dev entries driver <6>[ 0.260467] max77696-battery max77696-battery.0: Voltage alert 3400mV ... 4260mV <6>[ 0.260884] max77696-battery max77696-battery.0: SOC alert (disabled) <6>[ 0.261775] MAX77696 Fuel Gauge Driver 1.0.0 Installed <6>[ 0.263908] MAX77696 USB Interface Circuit Driver 1.0.0 Installed <6>[ 0.266775] max77696-adc max77696-adc.0: ADC average rate: 32 sample(s) <6>[ 0.266785] max77696-adc max77696-adc.0: ADC delay: 0 nsec <6>[ 0.266793] max77696-adc max77696-adc.0: ADC cur src: 50 uA <6>[ 0.266802] MAX77696 ADC Driver 1.0.1 Installed <6>[ 0.267284] imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1) <6>[ 0.268124] sdhci: Secure Digital Host Controller Interface driver <6>[ 0.268133] sdhci: Copyright(c) Pierre Ossman <6>[ 0.268253] mmc0: no vmmc regulator found <7>[ 0.269273] sdhci: =========== REGISTER DUMP (mmc0)=========== <4>[ 0.269281] <4>[ 0.269283] 0xe0858000: 00000000 00010200 00000000 083a0000 <4>[ 0.269294] 0xe0858010: 00000900 fffffffd 320f5903 00000b00 <4>[ 0.269304] 0xe0858020: 00000000 ff888088 08800024 008e0118 <4>[ 0.269314] 0xe0858030: 00000000 007f0003 007f0003 00000000 <4>[ 0.269323] 0xe0858040: 07f3b407 08000880 00000011 00000000 <4>[ 0.269333] 0xe0858050: 00000000 00000000 00000000 00000000 <4>[ 0.269342] 0xe0858060: 00000000 00000200 00000000 0800ff00 <4>[ 0.269351] 0xe0858070: 00000000 00000000 00000000 00000000 <4>[ 0.269361] 0xe0858080: 00000000 00000000 00000000 00000000 <4>[ 0.269370] 0xe0858090: 00000000 00000000 00000000 00000000 <4>[ 0.269380] 0xe08580a0: 00000000 00000000 00000000 00000000 <4>[ 0.269389] 0xe08580b0: 00000000 00000000 00000000 00000000 <4>[ 0.269399] 0xe08580c0: 2000780b 00000000 00000006 00212800 <7>[ 0.269411] CCM: CSCMR1(0x00f00040), CSCDR1(0x00490b40) <7>[ 0.269417] CCM: CCOSR(0x000a000c), CCGR6(0x00000030) <7>[ 0.269423] CCM: CMEOR(0x7fffffff) <7>[ 0.269428] sdhci: =========================================== <6>[ 0.269675] mmc0: SDHCI controller on platform [sdhci-esdhc-imx.1] using DMA <6>[ 0.270757] mmc1: no vmmc regulator found <7>[ 0.271774] sdhci: =========== REGISTER DUMP (mmc1)=========== <4>[ 0.271781] <4>[ 0.271783] 0xe0860000: 00000000 00010000 00000000 00000000 <4>[ 0.271794] 0xe0860010: 00000000 00000000 00000000 00000000 <4>[ 0.271803] 0xe0860020: 00000000 ff888088 08800020 0080800f <4>[ 0.271813] 0xe0860030: 00000000 007f0003 007f0003 00000000 <4>[ 0.271823] 0xe0860040: 07f3b407 08100810 80000000 00000000 <4>[ 0.271833] 0xe0860050: 00000000 00000000 00000000 00000000 <4>[ 0.271842] 0xe0860060: 00000000 00000200 00000000 0800ff00 <4>[ 0.271852] 0xe0860070: 00000000 00000000 00000000 00000000 <4>[ 0.271861] 0xe0860080: 00000000 00000000 00000000 00000000 <4>[ 0.271870] 0xe0860090: 00000000 00000000 00000000 00000000 <4>[ 0.271879] 0xe08600a0: 00000000 00000000 00000000 00000000 <4>[ 0.271888] 0xe08600b0: 00000000 00000000 00000000 00000000 <4>[ 0.271897] 0xe08600c0: 2000780b 00000000 00000006 00212800 <7>[ 0.271909] CCM: CSCMR1(0x00f00040), CSCDR1(0x00490b40) <7>[ 0.271915] CCM: CCOSR(0x000a000c), CCGR6(0x000000c0) <7>[ 0.271921] CCM: CMEOR(0x7fffffff) <7>[ 0.271925] sdhci: =========================================== <6>[ 0.272009] mmc0: mmc_rescan_try_freq: trying to init card at 400000 Hz <6>[ 0.273406] mmc1: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA <7>[ 0.274108] Registered led device: max77696-leds.0 <6>[ 0.274118] MAX77696 LED Driver #0 1.0.0 Installed <7>[ 0.274278] Registered led device: max77696-leds.1 <6>[ 0.274286] MAX77696 LED Driver #1 1.0.0 Installed <6>[ 0.274771] usbcore: registered new interface driver snd-usb-audio <6>[ 0.274781] ALSA device list: <6>[ 0.274786] No soundcards found. <6>[ 0.275288] nf_conntrack version 0.5.0 (8023 buckets, 32092 max) <6>[ 0.275924] ip_tables: (C) 2000-2006 Netfilter Core Team <6>[ 0.275981] TCP cubic registered <6>[ 0.275990] NET: Registered protocol family 17 <6>[ 0.276009] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <3>[ 0.276144] LPDDR2 MfgId: 0x1 [Samsung] <3>[ 0.280004] <3>[ 0.280006] just text: vaddr c014cffc, va 0xc014c200 pa 0x801000c3 attr 0x6 <3>[ 0.292584] <3>[ 0.292587] nmx6sl_wfi_iram: vaddr e084e000, va 0xe084e200 pa 0x904043 attr 0x2 <3>[ 0.301430] <3>[ 0.301432] mx6sl_ddr: vaddr e0856000, va 0xe0856200 pa 0x905043 attr 0x2 <3>[ 0.309767] <3>[ 0.309769] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149 <3>[ 0.320603] <3>[ 0.320606] ANATOP: vaddr f40c8000, va 0xf40c8200 pa 0x20110c3 attr 0x149 <3>[ 0.334896] <3>[ 0.334899] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149 <3>[ 0.343078] <3>[ 0.343080] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149 <3>[ 0.355562] <3>[ 0.355565] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149 <3>[ 0.365343] <3>[ 0.365345] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149 <6>[ 0.376097] Bus freq driver module loaded <6>[ 0.378181] Bus freq driver Enabled <6>[ 0.386582] mxc_dvfs_core_probe <6>[ 0.386825] DVFS driver module loaded <4>[ 0.388678] regulator_init_complete: max77696_ldo10: incomplete constraints, leaving on <4>[ 0.389322] regulator_init_complete: max77696_ldo7: incomplete constraints, leaving on <4>[ 0.389543] regulator_init_complete: max77696_ldo6: incomplete constraints, leaving on <4>[ 0.390813] regulator_init_complete: max77696_buck6: incomplete constraints, leaving on <4>[ 0.391034] regulator_init_complete: max77696_buck5: incomplete constraints, leaving on <4>[ 0.391466] regulator_init_complete: max77696_buck2dvs: incomplete constraints, leaving on <4>[ 0.391687] regulator_init_complete: max77696_buck1dvs: incomplete constraints, leaving on <7>[ 0.408701] max77696-rtc max77696-rtc.0: read time: <7>[ 0.408714] max77696-rtc max77696-rtc.0: YEAR 00 MONTH 01 DOM 0C DOW 10 HOUR 02 MIN 35 SEC 31 <7>[ 0.408726] max77696-rtc max77696-rtc.0: --> 2000-01-12 Thu 02:53:49 <6>[ 0.408747] max77696-rtc max77696-rtc.0: setting system clock to 2000-01-12 02:53:49 UTC (947645629) <6>[ 0.421725] KERNEL: I pmic:charger chgina::charger connected <6>[ 0.427037] MAX77696 Main Charger Driver 1.0.0 Installed <6>[ 0.430264] MAX77696 Energy Harvester Driver 1.0.0 Installed <6>[ 0.430832] Freeing init memory: 1216K <4>[ 0.432312] ERROR:/proc/serial:No such file or directory(2) <6>[ 0.455752] emmc: I def:mmcpartinfo:vendor=sandisk, host=mmc0: <6>[ 0.490544] mmc0: new high speed DDR MMC card at address 0001 <6>[ 0.490822] mmcblk0: mmc0:0001 SEM04G 3.68 GiB <6>[ 0.490945] mmcblk0boot0: mmc0:0001 SEM04G partition 1 2.00 MiB <6>[ 0.491064] mmcblk0boot1: mmc0:0001 SEM04G partition 2 2.00 MiB <6>[ 0.491908] mmcblk0: p1 p2 p3 p4 <6>[ 0.493999] mmcblk0boot1: unknown partition table <6>[ 0.495821] mmcblk0boot0: unknown partition table <6>[ 0.496002] mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz <4>[ 0.545140] INFO:find_file:160 Found 320_R094_AE2521_ED060KD1C2_TC.wrf.gz <4>[ 0.545199] ERROR:wfm_count=1 <4>[ 0.554383] mxc_epdc_eink: module license 'proprietary' taints kernel. <4>[ 0.554395] Disabling lock debugging due to kernel taint <4>[ 0.554716] INFO:Loaded module /lib/modules/mxc_epdc_eink.ko (11924 bytes) <6>[ 0.574040] imx_epdc_fb imx_epdc_fb: Found a video mode override (EGS) <6>[ 0.582030] mmc1: mmc_rescan_try_freq: trying to init card at 300000 Hz <6>[ 0.654659] mmc1: mmc_rescan_try_freq: trying to init card at 200000 Hz <6>[ 0.727295] mmc1: mmc_rescan_try_freq: trying to init card at 100000 Hz <6>[ 1.184897] add wake up source irq 104 <6>[ 1.694698] Retrieved voltage control information <6>[ 1.753564] kernel: kernel_metric_high_priority,947645630,counter,kern el,max77696-epd,VEE_fault,1, <6>[ 1.753598] kernel: kernel_metric_high_priority,947645630,counter,kern el,max77696-epd,VNEG_fault,1, <6>[ 1.753626] kernel: kernel_metric_high_priority,947645630,counter,kern el,max77696-epd,VDD_fault,1, <3>[ 1.753654] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] <3>[ 1.760933] Regulator Fault Occurred! Retrying powerup... <6>[ 1.838112] kernel: kernel_metric_high_priority,947645630,counter,kern el,max77696-epd,VEE_fault,1, <6>[ 1.838142] kernel: kernel_metric_high_priority,947645630,counter,kern el,max77696-epd,VNEG_fault,1, <6>[ 1.838170] kernel: kernel_metric_high_priority,947645630,counter,kern el,max77696-epd,VDD_fault,1, <3>[ 1.838194] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] <3>[ 1.845459] Regulator Fault Occurred! Retrying powerup... <6>[ 1.918066] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VEE_fault,1, <6>[ 1.918096] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VNEG_fault,1, <6>[ 1.918123] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VDD_fault,1, <3>[ 1.918148] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] <3>[ 1.925411] Regulator Fault Occurred! Retrying powerup... <6>[ 1.946576] kernel: kernel_metric_high_priority,947645631,counter,kern el,imx_epdc_fb,powerup_timeout,1, <3>[ 1.947612] imx_epdc_fb imx_epdc_fb: EPDC powerup timeout/error. <6>[ 2.006858] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VEE_fault,1, <6>[ 2.006889] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VNEG_fault,1, <6>[ 2.006916] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VDD_fault,1, <3>[ 2.006940] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] <3>[ 2.014176] Regulator Fault Occurred! Retrying powerup... <6>[ 2.088133] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VEE_fault,1, <6>[ 2.088163] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VNEG_fault,1, <6>[ 2.088189] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VDD_fault,1, <3>[ 2.088213] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] <3>[ 2.095474] Regulator Fault Occurred! Retrying powerup... <6>[ 2.168119] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VEE_fault,1, <6>[ 2.168149] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VNEG_fault,1, <6>[ 2.168177] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VDD_fault,1, <3>[ 2.168200] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] <3>[ 2.175461] Regulator Fault Occurred! Retrying powerup... <6>[ 2.196518] kernel: kernel_metric_high_priority,947645631,counter,kern el,imx_epdc_fb,powerup_timeout,1, <3>[ 2.197553] imx_epdc_fb imx_epdc_fb: EPDC powerup timeout/error. <6>[ 2.254927] KERNEL: I pmic:fg battery id check::wario_battery_valid=1 <6>[ 2.256812] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VEE_fault,1, <6>[ 2.256842] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VNEG_fault,1, <6>[ 2.256869] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VDD_fault,1, <3>[ 2.256894] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] <3>[ 2.264130] Regulator Fault Occurred! Retrying powerup... <6>[ 2.338149] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VEE_fault,1, <6>[ 2.338179] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VNEG_fault,1, <6>[ 2.338206] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VDD_fault,1, <3>[ 2.338230] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] <3>[ 2.345492] Regulator Fault Occurred! Retrying powerup... <6>[ 2.418181] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VEE_fault,1, <6>[ 2.418210] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VNEG_fault,1, <6>[ 2.418238] kernel: kernel_metric_high_priority,947645631,counter,kern el,max77696-epd,VDD_fault,1, <3>[ 2.418261] max77696-epd max77696-epd.0: EPDINT: Regulator Fault Detected [1a] <3>[ 2.425523] Regulator Fault Occurred! Retrying powerup... <6>[ 2.446588] kernel: kernel_metric_high_priority,947645631,counter,kern el,imx_epdc_fb,powerup_timeout,1, <3>[ 2.447602] imx_epdc_fb imx_epdc_fb: EPDC powerup timeout/error. <3>[ 2.453638] imx_epdc_fb imx_epdc_fb: Failed to do initialization sequence -901 <6>[ 2.464960] Device spi0.0 removed <4>[ 2.465108] imx_epdc_fb: probe of imx_epdc_fb failed with error -901 <4>[ 2.465577] ERROR:insmod(/lib/modules/mxc_epdc_fb.ko) : init_module error: No such device (19) <4>[ 2.465755] ERROR:eink_init: failed to load eink driver /lib/modules/mxc_epdc_fb.ko: No such device (19) <4>[ 2.465791] INFO:Rebooting ... <4>[ 2.465887] ERROR:failed to create failure log... -1 === END === [ 10.010624] imx2-wdt imx2-wdt.0: Device shutdown: Expect reboot! [ 10.017797] Restarting system. HW

04-04-2020, 07:22 PM	#2
knc1 Going Viral Posts: 17,212 Karma: 18210809 Join Date: Feb 2012 Location: Central Texas Device: No K1, PW2, KV, KOA	Code: <3>[ 2.345492] Regulator Fault Occurred! Retrying powerup... Seems like a solid hardware error message to me. And: Code: I try use fastboot in bist, and consale say all time "battery voltage: xxxx mV That is the standard output while the fastboot host is running, which is the command you gave the machine. Last edited by knc1; 04-04-2020 at 07:29 PM.

Advert

04-06-2020, 08:14 AM

thoriki

Member

Posts: 17

Karma: 26

Join Date: Jan 2020

Device: kindle paperwhite 7th, and 10th

Quote:

Originally Posted by knc1

Code:

<3>[    2.345492] Regulator Fault Occurred! Retrying powerup...

Seems like a solid hardware error message to me.
And:

Code:

I try use fastboot in bist, and consale say all time "battery voltage: xxxx mV

That is the standard output while the fastboot host is running, which is the command you gave the machine.

ty very for u reply (sorry my english is very badly)
i read u reply and disonnect all and reconnet and, no have this error more.

have other problems, i follow steps guide and have 2 problems.

1º i put ""bootm 0xE41000""
and this is result (cant get next step of guide)

Spoiler:

2º in the previous spoiler I have been able to see one line say "press enter for recovery menu" i enter and cant follow new step os guide.

Spoiler:

please who can help me? (ty very all)

04-06-2020, 11:48 AM	#4
knc1 Going Viral Posts: 17,212 Karma: 18210809 Join Date: Feb 2012 Location: Central Texas Device: No K1, PW2, KV, KOA	You are leaving the usb cable connected during boot. Do not do that.

04-06-2020, 01:07 PM

thoriki

Member

Posts: 17

Karma: 26

Join Date: Jan 2020

Device: kindle paperwhite 7th, and 10th

Quote:

Originally Posted by knc1

You are leaving the usb cable connected during boot.
Do not do that.

ty very for u reply, solve problem "exit login" and can run next steps to
"Part 5: Install some goodies

We will put some basics onto your kindle now that it's been uncaged

1. Install KUAL ""

i follow al steps and cant see files copied in douments folder, and all books is deleted, i try hard reset (facctory reset, and kindle update to the 5.12.4 :S, register pw3 and an see all my books, (no on my device, only for click and download :S ¿?¿?¿ )
I do everything again step by step and same problem in

"Part 5: Install some goodies

We will put some basics onto your kindle now that it's been uncaged

1. Install KUAL ""

cant see files have copied in douments folder , cant see on my pw3

Advert

04-06-2020, 04:19 PM	#6
thoriki Member Posts: 17 Karma: 26 Join Date: Jan 2020 Device: kindle paperwhite 7th, and 10th	i install Update_KUALBooklet_hotfix_v2.7.23_install.bin and can end all steps !!!! cheer !!!!! ty all !!!!!! my son have other paperwhite 3, no have free pop'up, if i do you will be able to use the screensaver hack, or cant use in device of my son ? sorry my englsih is very badly (have advertising in pw3 of my son )

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
PW3 PW3-4, PW3-32, fw-5.8.9.0.1 software jailbreak	knc1	Kindle Developer's Corner	203	01-27-2020 11:53 PM
PRS-T1 bootloop	charmees	Sony Reader	9	11-23-2018 03:13 PM
PW3 PW3 G090G1 Bootloop ???	tyi2ael	Kindle Developer's Corner	6	11-08-2018 03:02 PM
PRS-T1 bootloop	klaasvaak42	Sony Reader	0	10-20-2018 04:45 AM