K3 fell unconscious, replacing the wifi chip, kubrick attempt

ton4eff · 12-28-2019, 01:06 PM

Kindle 3 WiFi + 3G - just suddenly stopped working. No reaction on slide button, no USB connection - nothing. Only orange light for about 30secs. Battery was at 90% at that time. Opened and measured some voltages. 1.8V line was dead shorted to GND. The wifi chip was warmer of all suspects (finger detected

), so it was de-soldered. Measured the 1.8V pads for short and indeed there was a short to GND inside the chip itself. It is unobtainable, so I bought а broken K3 pcb for cheap as a donor for Atheros AR 6102G wifi chip, hoping that it's alive.
The replaced wifi chip:

Now 1.8V is OK and reader starts to boot, but then stops on about 30%. Connected via USB to serial (1.8V) using PuTTY. Booting process always stopped at the message for some problem with AR6 and saying that something was wrong with the MAC address (forgot to copy exactly, sorry). I decided to use Kubrick to see what will happen... It took about 3 hours, everything went smoothly, but still no luck. Only now booting process looks kind of different and I don't know what to do next... Any ideas?

Here is how the booting process looks now:

Code:

U-Boot 1.3.0-rc3-lab126 (Apr 16 2011 - 20:15:23)

CPU:   Freescale i.MX35 at 532 MHz
Board: MX35 Luigi [ POR]
WDOG_WCR = 0xff31
WDOG_WMCR = 0x0
Board Id: SP1B000000000000
S/N: B00AA0A004850761
DRAM:  256 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
No ethernet found.
i.MX35 CPU board version 2.0
Net:   No ethernet found.
Hit any key to stop autoboot:  0
## Booting image at 87f40400 ...
   Image Name:   Linux-2.6.26-rt-lab126
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2167548 Bytes =  2.1 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

Uncompressing Linux.......................................................................................................................... done, booting the kernel.
boot: C def:bcut:batterycut=1,version=s172597:
2.6.26-rt-lab126 #5 Sat Sep 1 14:28:26 PDT 2012 armv6l
INFO:Using default keypad setting. (not passing "kb_rev" to module)
INFO:Loaded module /lib/modules/mxc_keyb.ko  (22508 bytes)
Press [ENTER] for recovery menu...       0 /INFO:Partition table verified for /dev/mmcblk0
INFO:Checking for updates... (auto-pilot mode)
/dev/mmcblk0p4:
CHS=4/16/98887 size=3240329216 bytes
flag type      first       last  lba first   lba size
Partition p1:
0x00 0x0b      24072 <large>          7688    6321080
    CHS: 376/0/9 - <large>
Partition p2:
Partition p3:
Partition p4:
INFO:Setup loop device /dev/loop0 for /dev/mmcblk0p4 + 3936256
INFO:No update*.bin found; no update needed.
INFO:no updates found.
BOOTING DEFAULT.
  argc == 9
  argv[0]: "kinit"
  argv[1]: "console=ttymxc0,115200"
  argv[2]: "mem=256M"
  argv[3]: "panic=10"
  argv[4]: "root=/dev/mmcblk0p1"
  argv[5]: "ro"
  argv[6]: "ip=none"
  argv[7]: "quiet"
  argv[8]: "lpj=2555904"
Running ipconfig
  argc == 4
  argv[0]: "IP-Config"
  argv[1]: "-i"
  argv[2]: "Linux kinit"
  argv[3]: "ip=none"
IP-Config: no devices to configure
kinit: do_mounts
kinit: name_to_dev_t(/dev/mmcblk0p1) = dev(179,1)
kinit: root_dev = dev(179,1)
kinit: /dev/root appears to be a ext3 filesystem
kinit: trying to mount /dev/root on /root with type ext3
kinit: Mounted root (ext3 filesystem) readonly.
Checking for init: /sbin/init
Checking for init: /bin/init
Checking for init: /etc/init
Checking for init: /sbin/init.sysvinit
INIT: version 2.86 booting
system: I rcS:def:starting /etc/rcS.d/S02kdb
system: I S02kdb:def:Setting boot device to mmcblk0
kdb set: 'system/driver/filesystem/DEV_ROOT'
system: I rcS:def:starting /etc/rcS.d/S03udev
system: I S03udev:def:setting up virtual fs for hotplug event handling
system: I S03udev:def:starting the hotplug events dispatcher
system: I S03udev:def:synthesizing initial hotplug events
lipc-send-event[378]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[378]: C def:dbusi::Failed to init dbus
lipc-send-event[378]: E def:open::Failed to open LIPC
lipc-send-event[378]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
lipc-send-event[474]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[474]: C def:dbusi::Failed to init dbus
lipc-send-event[474]: E def:open::Failed to open LIPC
lipc-send-event[474]: E def:fail:source=com.lab126.hal, event=audioHS:Sending event failed
system: I rcS:def:starting /etc/rcS.d/S04rootfsresize
system: I S04rootfsresize:def:No rootfs on /dev/mmcblk0p1 resizing needed
system: I rcS:def:starting /etc/rcS.d/S10filesystems
system: I rcS:def:starting /etc/rcS.d/S10hostname
system: I rcS:def:starting /etc/rcS.d/S10network
system: I S10hostname:def:setting device hostname
system: I S10filesystems:def:mounting filesystems
system: I S10network:def:initializing network configuration
system: I S10network:def:Installed Firewall
system: I rcS:def:starting /etc/rcS.d/S11chpriority
system: I rcS:def:starting /etc/rcS.d/S11video
Unknown HZ value! (94) Assume 100.
system: W S11chpriority:def:Cannot set priority for IRQ-7
system: I S11video:def:initializing eInk HAL for system use
system: I S11video:def:eink_debug=0
system: I S11video:def:Controller set to broads
system: I rcS:def:starting /etc/rcS.d/S20syslog-ng
system: I S20syslog-ng:def:starting syslog-ng
system: I rcS:def:starting /etc/rcS.d/S21init_time
system: I S21init_time:initboot:time=15740:boot time after init in milliseconds
system: I rcS:def:starting /etc/rcS.d/S45modules
system: I S45modules:def:loading module mwan
system: I S45modules:def:loading module g_file_storage
system: I S45modules:def:loading module fuse
system: I S45modules:def:loading module uinput
system: I S45modules:def:loading module mxc_keyb
system: I S45modules:def:loading module fiveway
system: I S45modules:def:loading module volume
system: I rcS:def:starting /etc/rcS.d/S50system
mount: mount point /proc/bus/usb does not exist
Fri Jun  1 00:00:00 UTC 2012
system: I rcS:def:starting /etc/rcS.d/S55scroll
system: I S55scroll:def:skipping; no luigi-based work to do here
system: I rcS:def:starting /etc/rcS.d/S70ethernet
system: I rcS:def:starting /etc/rcS.d/S70userstore
system: I S70ethernet:def:not enet
system: I S70ethernet:def:not usbnet
system: I S70userstore:def:Found BOOTUP flag file
dosfsck 2.11-lab126 (1 Jun 2007)
dosfsck 2.11-lab126, 1 Jun 2007, FAT32, LFN
Checking we can access the last sector of the filesystem
Boot sector contents:
System ID "mkdosfs"
Media byte 0xf8 (hard disk)
       512 bytes per logical sector
      8192 bytes per cluster
        32 reserved sectors
First FAT starts at byte 16384 (sector 32)
         2 FATs, 32 bit entries
   1581056 bytes per FAT (= 3088 sectors)
Root directory start at cluster 2 (arbitrary size)
Data area starts at byte 3178496 (sector 6208)
    395159 data clusters (3237142528 bytes)
32 sectors/track, 64 heads
         0 hidden sectors
   6328752 sectors total
Orphaned long file name part ":ETZ:7Ue:BUY:5yQ:3K+:AST:FxU:1d6:BYE:BMv:1Op:8Z3:ExJ"
  Auto-deleting.
Long filename fragment ":4Fe:1no:1Tu:0hE:DTQ:E6I:Ei4:5cM:6u5:Cnf:BZ3:AXL:2bn" found outside a LFN sequence.
  (Maybe the start bit is missing on the last fragment)
  Not auto-correcting this.
Checksum in long filename part wrong (0d vs. expected 79).
  Not auto-correcting this.
/documents
  Has a large number of bad entries. (53/134)
  Not dropping it in auto-mode.
/.active-content-data/.delete
  Has a large number of bad entries. (54/124)
  Not dropping it in auto-mode.
/.active-content-data/.delete
  "." is missing. Can't fix this yet.
/.active-content-data/.delete
  ".." is missing. Can't fix this yet.
Unfinished long file name ":BKR:40W:2pA:Amj:E-X:2Kh:Ew2:3Pp:7Tl:DBs:3vA:0Sf:1oX".
  (Start may have been overwritten by FSCK0030.REN)
  Not auto-correcting this.
Wrong checksum for long file name ":BKR:40W:2pA:Amj:E-X:2Kh:Ew2:3Pp:7Tl:DBs:3vA:0Sf:1oX".
  (Short name FSCK0030.REN may have changed without updating the long name)
  Not auto-correcting this.
/BOOKS/Kindle/System Volume Information
  Has a large number of bad entries. (59/128)
  Not dropping it in auto-mode.
/BOOKS/Kindle/System Volume Information
  "." is missing. Can't fix this yet.
/BOOKS/Kindle/System Volume Information
  ".." is missing. Can't fix this yet.
Long filename fragment ":C0B:Byc:Fq2:3LS:53E:5Ha:7mA:0Sh:FwT:Aiy:DkM:AQ4:2mA" found outside a LFN sequence.
  (Maybe the start bit is missing on the last fragment)
  Not auto-correcting this.
Checksum in long filename part wrong (fd vs. expected ec).
  Not auto-correcting this.
/BOOKS/Kindle/developer
  Has a large number of bad entries. (63/124)
  Not dropping it in auto-mode.
/BOOKS/Kindle/developer
  "." is missing. Can't fix this yet.
/BOOKS/Kindle/developer
  ".." is missing. Can't fix this yet.
/BOOKS/Kindle/CR3
  Has a large number of bad entries. (46/126)
  Not dropping it in auto-mode.
/BOOKS/Kindle/CR3
  "." is missing. Can't fix this yet.
/BOOKS/Kindle/CR3
  ".." is missing. Can't fix this yet.
Long filename fragment ":AmH:7jm:0JN:7bS:9pu:D8n:6Tq:0kB:9PL:33r:D-6:5s+:0w0" found outside a LFN sequence.
  (Maybe the start bit is missing on the last fragment)
  Not auto-correcting this.
Checksum in long filename part wrong (3b vs. expected 5c).
  Not auto-correcting this.
Long filename fragment ":2PO:53f:DC9:FRO:8kF:Eyy:5sz:FVh:BJ8:0ZU:8K+:ApM:F1H" found outside a LFN sequence.
  (Maybe the start bit is missing on the last fragment)
  Not auto-correcting this.
Checksum in long filename part wrong (a9 vs. expected 5c).
  Not auto-correcting this.
/qtKindle/LIB/FONTS
  Has a large number of bad entries. (57/131)
  Not dropping it in auto-mode.
/qtKindle/LIB/FONTS
  "." is missing. Can't fix this yet.
/qtKindle/LIB/FONTS
  ".." is missing. Can't fix this yet.
/qtKindle/LIB/pkgconfig
  Has a large number of bad entries. (26/59)
  Not dropping it in auto-mode.
/qtKindle/LIB/pkgconfig
  "." is missing. Can't fix this yet.
/qtKindle/LIB/pkgconfig
  ".." is missing. Can't fix this yet.
/qtKindle/SHARE
  Has a large number of bad entries. (46/70)
  Not dropping it in auto-mode.
/qtKindle/SHARE
  "." is missing. Can't fix this yet.
/qtKindle/SHARE
  ".." is missing. Can't fix this yet.
/USRAPP
  Has a large number of bad entries. (20/44)
  Not dropping it in auto-mode.
/USRAPP
  "." is missing. Can't fix this yet.
/USRAPP
  ".." is missing. Can't fix this yet.
Checking for unused clusters.
Checking free cluster summary.
Performing changes.
/dev/loop/0: 1565 files, 17194/395159 clusters
system: I rcS:def:starting /etc/rcS.d/S90video
system: I S90video:def:initializing eInk HAL for rootfs use
INIT: Entering runlevel: 2
system: I lifeguard:def:starting eInk HAL lifeguard
system: I S40diags:def:not starting Diagnostic Services
system: I S40diags:def:/mnt/base-us/ENABLE_DIAGS does not exist, forcing diagnostic disable
system: I S50battcheck:def:running
Thu May 31 20:30:04 2012  INFO:battery voltage: 4016 mV
Thu May 31 20:30:04 2012  INFO:battery charge: 76%
system: I S50battcheck:def:current voltage = 4016mV
Thu May 31 20:30:04 2012  INFO:battery charge: 76%
Thu May 31 20:30:04 2012  INFO:battery voltage: 4016 mV
Thu May 31 20:30:04 2012  INFO:battery current: -134 mA
system: I S50battcheck:def:gasgauge capacity=76% volts=4016 mV current=-134 mA
system: I S50battcheck:def:Waiting for 3460mV or 4%
system: I S50battcheck:def:battery sufficient, booting to normal runlevel
INIT: Switching to runlevel: 5
INIT: Sending processes the TERM signal
Platform set to SHASTA_NATIVEMMC-SDIO
Platform Setup Script is: /opt/ar6k/host/support/platformscripts/plat_SHASTA_NATIVEMMC-SDIO.sh
Image path: /sbin
No debug record limit set
export AR6002_REV='2'
export AR6K_MODULE_ARGS='bmienable=1  ifname=wlan0 fwmode=1 busspeedlow=0'
export AR6K_MODULE_NAME='ar6000'
export AR6K_TGT_LOGFILE='/tmp/dbglog.out'
export ATH_PLATFORM='SHASTA_NATIVEMMC-SDIO'
export ATH_SDIO_STACK_PARAMS='RequestListSize=128 '
export CONSOLE='/dev/console'
export EEPROM='/opt/ar6k/target/AR6002/hw2.0/bin/lab126_15dBm_nodiv_WWR_CTL.bin'
export HOME='/'
export IMAGEPATH='/sbin'
export INIT_VERSION='sysvinit-2.86'
export PATH='/bin:/usr/bin:/sbin:/usr/sbin'
export PREVLEVEL='2'
export PWD='/'
export RUNLEVEL='5'
export TARGET='AR6002'
export TARGET_TYPE='AR6002'
export TERM='linux'
export VERBOSE='no'
export WORKAREA='/opt/ar6k'
export previous='2'
export runlevel='5'
Load Board Data from /opt/ar6k/target/AR6002/hw2.0/bin/lab126_15dBm_nodiv_WWR_CTL.bin
Updating MAC address
/sbin/eeprom.AR6002 is waiting for Target....
▒^U7.▒▒ѥ▒▒▒this.
Checksum in long filename part wrong (0d vs. expected 79).
  Not auto-correcting this.
/documents
  Has a large number of bad entries. (53/134)
  Not dropping it in auto-mode.
/.active-content-data/.delete
  Has a large number of bad entries. (54/124)
  Not dropping it in auto-mode.
/.active-content-data/.delete
  "." is missing. Can't fix this yet.
/.active-content-data/.delete
  ".." is missing. Can't fix this yet.
Unfinished long file name ":BKR:40W:2pA:Amj:E-X:2Kh:Ew2:3Pp:7Tl:DBs:3vA:0Sf:1oX".
  (Start may have been overwritten by FSCK0030.REN)
  Not auto-correcting this.
Wrong checksum for long file name ":BKR:40W:2pA:Amj:E-X:2Kh:Ew2:3Pp:7Tl:DBs:3vA:0Sf:1oX".
  (Short name FSCK0030.REN may have changed without updating the long name)
  Not auto-correcting this.
/BOOKS/Kindle/System Volume Information
  Has a large number of bad entries. (59/128)
  Not dropping it in auto-mode.
/BOOKS/Kindle/System Volume Information
  "." is missing. Can't fix this yet.
/BOOKS/Kindle/System Volume Information
  ".." is missing. Can't fix this yet.
Long filename fragment ":C0B:Byc:Fq2:3LS:53E:5Ha:7mA:0Sh:FwT:Aiy:DkM:AQ4:2mA" found outside a LFN sequence.
  (Maybe the start bit is missing on the last fragment)
  Not auto-correcting this.
Checksum in long filename part wrong (fd vs. expected ec).
  Not auto-correcting this.
/BOOKS/Kindle/developer
  Has a large number of bad entries. (63/124)
  Not dropping it in auto-mode.
/BOOKS/Kindle/developer
  "." is missing. Can't fix this yet.
/BOOKS/Kindle/developer
  ".." is missing. Can't fix this yet.
/BOOKS/Kindle/CR3
  Has a large number of bad entries. (46/126)
  Not dropping it in auto-mode.
/BOOKS/Kindle/CR3
  "." is missing. Can't fix this yet.
/BOOKS/Kindle/CR3
  ".." is missing. Can't fix this yet.
Long filename fragment ":AmH:7jm:0JN:7bS:9pu:D8n:6Tq:0kB:9PL:33r:D-6:5s+:0w0" found outside a LFN sequence.
  (Maybe the start bit is missing on the last fragment)
  Not auto-correcting this.
Checksum in long filename part wrong (3b vs. expected 5c).
  Not auto-correcting this.
Long filename fragment ":2PO:53f:DC9:FRO:8kF:Eyy:5sz:FVh:BJ8:0ZU:8K+:ApM:F1H" found outside a LFN sequence.
  (Maybe the start bit is missing on the last fragment)
  Not auto-correcting this.
Checksum in long filename part wrong (a9 vs. expected 5c).
  Not auto-correcting this.
/qtKindle/LIB/FONTS
  Has a large number of bad entries. (57/131)
  Not dropping it in auto-mode.
/qtKindle/LIB/FONTS
  "." is missing. Can't fix this yet.
/qtKindle/LIB/FONTS
  ".." is missing. Can't fix this yet.
/qtKindle/LIB/pkgconfig
  Has a large number of bad entries. (26/59)
  Not dropping it in auto-mode.
/qtKindle/LIB/pkgconfig
  "." is missing. Can't fix this yet.
/qtKindle/LIB/pkgconfig
  ".." is missing. Can't fix this yet.
/qtKindle/SHARE
  Has a large number of bad entries. (46/70)
  Not dropping it in auto-mode.
/qtKindle/SHARE
  "." is missing. Can't fix this yet.
/qtKindle/SHARE
  ".." is missing. Can't fix this yet.
/USRAPP
  Has a large number of bad entries. (20/44)
  Not dropping it in auto-mode.
/USRAPP
  "." is missing. Can't fix this yet.
/USRAPP
  ".." is missing. Can't fix this yet.
Checking for unused clusters.
Checking free cluster summary.
Performing changes.
/dev/loop/0: 1565 files, 17194/395159 clusters
system: I rcS:def:starting /etc/rcS.d/S90video
system: I S90video:def:initializing eInk HAL for rootfs use
INIT: Entering runlevel: 2
system: I lifeguard:def:starting eInk HAL lifeguard
system: I S40diags:def:not starting Diagnostic Services
system: I S40diags:def:/mnt/base-us/ENABLE_DIAGS does not exist, forcing diagnostic disable
system: I S50battcheck:def:running
Thu May 31 20:30:04 2012  INFO:battery voltage: 4016 mV
Thu May 31 20:30:04 2012  INFO:battery charge: 76%
system: I S50battcheck:def:current voltage = 4016mV
Thu May 31 20:30:04 2012  INFO:battery charge: 76%
Thu May 31 20:30:04 2012  INFO:battery voltage: 4016 mV
Thu May 31 20:30:04 2012  INFO:battery current: -134 mA
system: I S50battcheck:def:gasgauge capacity=76% volts=4016 mV current=-134 mA
system: I S50battcheck:def:Waiting

ton4eff · 12-29-2019, 03:36 AM

After launching Kubrick for a second time from a different DVD, it looks exactly as it was before. Is the the new WiFi chip recognized or for some reason reader doesn't like the new MAC address...?

Code:

U-Boot 1.3.0-rc3-lab126 (Apr 16 2011 - 20:15:23)

CPU:   Freescale i.MX35 at 532 MHz
Board: MX35 Luigi [ POR]
WDOG_WCR = 0xff31
WDOG_WMCR = 0x0
Board Id: SP1B000000000000
S/N: B00AA0A004850761
DRAM:  256 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
No ethernet found.
i.MX35 CPU board version 2.0
Net:   No ethernet found.
Hit any key to stop autoboot:  0
## Booting image at 87f40400 ...
   Image Name:   Linux-2.6.26-rt-lab126
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2167548 Bytes =  2.1 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

Uncompressing Linux.......................................................................................................................... done, booting the kernel.
boot: C def:bcut:batterycut=1,version=s172597:
2.6.26-rt-lab126 #5 Sat Sep 1 14:28:26 PDT 2012 armv6l
INFO:Using default keypad setting. (not passing "kb_rev" to module)
INFO:Loaded module /lib/modules/mxc_keyb.ko  (22508 bytes)
Press [ENTER] for recovery menu...       0 /INFO:Partition table verified for /dev/mmcblk0
INFO:Checking for updates... (auto-pilot mode)
/dev/mmcblk0p4:
CHS=4/16/98887 size=3240329216 bytes
flag type      first       last  lba first   lba size
Partition p1:
0x00 0x0b         16 <large>            16    6328752
    CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
INFO:Setup loop device /dev/loop0 for /dev/mmcblk0p4 + 8192
INFO:No update*.bin found; no update needed.
INFO:no updates found.
BOOTING DEFAULT.
  argc == 9
  argv[0]: "kinit"
  argv[1]: "console=ttymxc0,115200"
  argv[2]: "mem=256M"
  argv[3]: "panic=10"
  argv[4]: "root=/dev/mmcblk0p1"
  argv[5]: "ro"
  argv[6]: "ip=none"
  argv[7]: "quiet"
  argv[8]: "lpj=2555904"
Running ipconfig
  argc == 4
  argv[0]: "IP-Config"
  argv[1]: "-i"
  argv[2]: "Linux kinit"
  argv[3]: "ip=none"
IP-Config: no devices to configure
kinit: do_mounts
kinit: name_to_dev_t(/dev/mmcblk0p1) = dev(179,1)
kinit: root_dev = dev(179,1)
kinit: /dev/root appears to be a ext3 filesystem
kinit: trying to mount /dev/root on /root with type ext3
kinit: Mounted root (ext3 filesystem) readonly.
Checking for init: /sbin/init
Checking for init: /bin/init
Checking for init: /etc/init
Checking for init: /sbin/init.sysvinit
INIT: version 2.86 booting
system: I rcS:def:starting /etc/rcS.d/S02kdb
system: I S02kdb:def:Setting boot device to mmcblk0
kdb set: 'system/driver/filesystem/DEV_ROOT'
system: I rcS:def:starting /etc/rcS.d/S03udev
system: I S03udev:def:setting up virtual fs for hotplug event handling
system: I S03udev:def:starting the hotplug events dispatcher
system: I S03udev:def:synthesizing initial hotplug events
lipc-send-event[378]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[378]: C def:dbusi::Failed to init dbus
lipc-send-event[378]: E def:open::Failed to open LIPC
lipc-send-event[378]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
lipc-send-event[475]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[475]: C def:dbusi::Failed to init dbus
lipc-send-event[475]: E def:open::Failed to open LIPC
lipc-send-event[475]: E def:fail:source=com.lab126.hal, event=audioHS:Sending event failed
system: I rcS:def:starting /etc/rcS.d/S04rootfsresize
system: I S04rootfsresize:def:No rootfs on /dev/mmcblk0p1 resizing needed
system: I rcS:def:starting /etc/rcS.d/S10filesystems
system: I rcS:def:starting /etc/rcS.d/S10hostname
system: I rcS:def:starting /etc/rcS.d/S10network
system: I S10hostname:def:setting device hostname
system: I S10filesystems:def:mounting filesystems
system: I S10network:def:initializing network configuration
system: I S10network:def:Installed Firewall
system: I rcS:def:starting /etc/rcS.d/S11chpriority
system: I rcS:def:starting /etc/rcS.d/S11video
Unknown HZ value! (94) Assume 100.
system: W S11chpriority:def:Cannot set priority for IRQ-7
system: I S11video:def:initializing eInk HAL for system use
system: I S11video:def:eink_debug=0
system: I S11video:def:Controller set to broads
system: I rcS:def:starting /etc/rcS.d/S20syslog-ng
system: I S20syslog-ng:def:starting syslog-ng
system: I rcS:def:starting /etc/rcS.d/S21init_time
system: I S21init_time:initboot:time=13600:boot time after init in milliseconds
system: I rcS:def:starting /etc/rcS.d/S45modules
system: I S45modules:def:loading module mwan
system: I S45modules:def:loading module g_file_storage
system: I S45modules:def:loading module fuse
system: I S45modules:def:loading module uinput
system: I S45modules:def:loading module mxc_keyb
system: I S45modules:def:loading module fiveway
system: I S45modules:def:loading module volume
system: I rcS:def:starting /etc/rcS.d/S50system
mount: mount point /proc/bus/usb does not exist
Fri Jun  1 00:00:00 UTC 2012
system: I rcS:def:starting /etc/rcS.d/S55scroll
system: I S55scroll:def:skipping; no luigi-based work to do here
system: I rcS:def:starting /etc/rcS.d/S70ethernet
system: I rcS:def:starting /etc/rcS.d/S70userstore
system: I S70ethernet:def:not enet
system: I S70ethernet:def:not usbnet
dosfsck 2.11-lab126 (1 Jun 2007)
dosfsck 2.11-lab126, 1 Jun 2007, FAT32, LFN
Checking we can access the last sector of the filesystem
Boot sector contents:
System ID "mkdosfs"
Media byte 0xf8 (hard disk)
       512 bytes per logical sector
      8192 bytes per cluster
        32 reserved sectors
First FAT starts at byte 16384 (sector 32)
         2 FATs, 32 bit entries
   1581056 bytes per FAT (= 3088 sectors)
Root directory start at cluster 2 (arbitrary size)
Data area starts at byte 3178496 (sector 6208)
    395159 data clusters (3237142528 bytes)
32 sectors/track, 64 heads
         0 hidden sectors
   6328752 sectors total
Checking for unused clusters.
Checking free cluster summary.
/dev/loop/0: 6 files, 159/395159 clusters
system: I rcS:def:starting /etc/rcS.d/S90video
system: I S90video:def:initializing eInk HAL for rootfs use
INIT: Entering runlevel: 2
system: I lifeguard:def:starting eInk HAL lifeguard
system: I S40diags:def:not starting Diagnostic Services
system: I S40diags:def:/mnt/base-us/ENABLE_DIAGS does not exist, forcing diagnostic disable
system: I S50battcheck:def:running
Fri Jun  1 00:00:03 2012  INFO:battery voltage: 4022 mV
Fri Jun  1 00:00:03 2012  INFO:battery charge: 88%
system: I S50battcheck:def:current voltage = 4037mV
Fri Jun  1 00:00:04 2012  INFO:battery charge: 88%
Fri Jun  1 00:00:04 2012  INFO:battery voltage: 4022 mV
Fri Jun  1 00:00:04 2012  INFO:battery current: -149 mA
system: I S50battcheck:def:gasgauge capacity=88% volts=4022 mV current=-149 mA
system: I S50battcheck:def:Waiting for 3460mV or 4%
system: I S50battcheck:def:battery sufficient, booting to normal runlevel
INIT: Switching to runlevel: 5
INIT: Sending processes the TERM signal
Platform set to SHASTA_NATIVEMMC-SDIO
Platform Setup Script is: /opt/ar6k/host/support/platformscripts/plat_SHASTA_NATIVEMMC-SDIO.sh
Image path: /sbin
No debug record limit set
export AR6002_REV='2'
export AR6K_MODULE_ARGS='bmienable=1  ifname=wlan0 fwmode=1 busspeedlow=0'
export AR6K_MODULE_NAME='ar6000'
export AR6K_TGT_LOGFILE='/tmp/dbglog.out'
export ATH_PLATFORM='SHASTA_NATIVEMMC-SDIO'
export ATH_SDIO_STACK_PARAMS='RequestListSize=128 '
export CONSOLE='/dev/console'
export EEPROM='/opt/ar6k/target/AR6002/hw2.0/bin/lab126_15dBm_nodiv_WWR_CTL.bin'
export HOME='/'
export IMAGEPATH='/sbin'
export INIT_VERSION='sysvinit-2.86'
export PATH='/bin:/usr/bin:/sbin:/usr/sbin'
export PREVLEVEL='2'
export PWD='/'
export RUNLEVEL='5'
export TARGET='AR6002'
export TARGET_TYPE='AR6002'
export TERM='linux'
export VERBOSE='no'
export WORKAREA='/opt/ar6k'
export previous='2'
export runlevel='5'
Load Board Data from /opt/ar6k/target/AR6002/hw2.0/bin/lab126_15dBm_nodiv_WWR_CTL.bin
Updating MAC address
/sbin/eeprom.AR6002 is waiting for Target....

knc1 · 12-29-2019, 12:09 PM

Is the chip you show now identical with the one you removed?

Why:
There are at least 3 (three) different K3 engineering builds.

ton4eff · 12-29-2019, 04:08 PM

Yes - Atheros AR 6102G. I decided to remove the chip and try to boot the reader without it. The boot process stops exactly on the same place with exactly the same messages. That should mean that the chip I'm soldering is not functional. Unfortunately it is unobtainable anywhere...

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Booting PW2 without WiFi chip	snipchip	Kindle Developer's Corner	6	12-17-2015 07:19 PM
SS with Kubrick	jonojono	Kindle Developer's Corner	0	07-22-2013 04:04 AM
Replacing the Kindle OS with Debian on my Kindle Touch Wifi	mattl	Kindle Developer's Corner	19	03-05-2012 11:27 AM
Replacing code without replacing text?	ElMiko	Sigil	6	11-30-2011 08:14 PM

12-29-2019, 12:09 PM	#3
knc1 Going Viral Posts: 17,212 Karma: 18210809 Join Date: Feb 2012 Location: Central Texas Device: No K1, PW2, KV, KOA	Is the chip you show now identical with the one you removed? Why: There are at least 3 (three) different K3 engineering builds.

12-29-2019, 04:08 PM	#4
ton4eff Junior Member Posts: 4 Karma: 10 Join Date: Dec 2019 Location: Bulgaria Device: Kindle 3	Yes - Atheros AR 6102G. I decided to remove the chip and try to boot the reader without it. The boot process stops exactly on the same place with exactly the same messages. That should mean that the chip I'm soldering is not functional. Unfortunately it is unobtainable anywhere...

Advert