Quote:
Originally Posted by geekmaster
in SSH, type
dmesg
which will display them. These are the same messages you see if you connect to the serial port during startup. Or do:
dmesg > /mnt/us/dmesg.log
to save them to the USB drive.
|
dmesg.log:
Code:
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 254500KB available (3716K code, 373K data, 1076K init, 0K highmem)
NR_IRQS:368
MXC IRQ initialized
cko2_set_rate, new divider=5
MXC_Early serial console at MMIO 0x53fbc000 (options '115200')
console [ttymxc0] enabled
Console: colour dummy device 80x30
Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
regulator: core version 0.5
NET: Registered protocol family 16
i.MX IRAM pool: 128 KB@0xd0840000
CPU is i.MX50 Revision 1.1
MXC GPIO hardware
Configure EMI_CS1 for whitney
Using SDMA I.API
MXC DMA API initialized
bio: create slab <bio-0> at 0
mxc_spi mxc_spi.0: can't setup spi1.0, status -22
CSPI: mxc_spi-0 probed
CSPI: mxc_spi-1 probed
mxc_spi mxc_spi.2: chipselect 0 already in use
CSPI: mxc_spi-2 probed
MXC I2C driver
MXC I2C driver
MXC I2C driver
PMIC Light driver loading...
mc13892 Rev 2.1 FinVer 2 detected
Setting ichrg to 1
Initializing regulators for mx50 yoshi.
regulator: SW1: 600 <--> 1375 mV
regulator: SW2: 900 <--> 1850 mV
regulator: SW3: 900 <--> 1850 mV
regulator: SW4: 1100 <--> 1850 mV
regulator: SWBST: 0 mV
regulator: VIOHI: 0 mV
regulator: VPLL: 1050 <--> 1800 mV
regulator: VDIG: 1200 mV
regulator: VSD: 1800 <--> 3150 mV
regulator: VUSB2: 2400 <--> 2775 mV
regulator: VVIDEO: 2775 mV
regulator: VAUDIO: 2300 <--> 3000 mV
regulator: VCAM: 2500 <--> 3000 mV fast normal
regulator: VGEN1: 3000 mV
regulator: VGEN2: 1200 <--> 3150 mV
regulator: VGEN3: 1800 mV
regulator: VUSB: 0 mV
regulator: GPO1: 0 mV
regulator: GPO2: 0 mV
regulator: GPO3: 0 mV
regulator: GPO4: 0 mV
PMIC ADC start probe
PMIC Light successfully loaded
Device spi3.0 probed
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
LPMode driver module loaded
Static Power Management for Freescale i.MX5
PM driver module loaded
sdram autogating driver module loaded
Bus freq driver module loaded
Initializing MX50 Yoshi Accessory Port
mxc_dvfs_core_probe
DVFS driver module loaded
i.MXC CPU frequency driver
msgmni has been set to 497
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
regulator: DISPLAY: 0 mV
regulator: GVDD: 20000 mV
regulator: GVEE: -22000 mV
regulator: VCOM: 0 <--> 2749 mV
regulator: VNEG: -15000 mV
regulator: VPOS: 15000 mV
regulator: TMST: 0 mV
papyrus 1-0048: PMIC PAPYRUS for eInk display
Amazon MX35 Yoshi Power Button Driver
Serial: MXC Internal UART driver
mxcintuart.0: ttymxc0 at MMIO 0x53fbc000 (irq = 31) is a Freescale MXC
console handover: boot [ttymxc0] -> real [ttymxc0]
mxcintuart.1: ttymxc1 at MMIO 0x53fc0000 (irq = 32) is a Freescale MXC
mxcintuart.2: ttymxc2 at MMIO 0x5000c000 (irq = 33) is a Freescale MXC
mxcintuart.3: ttymxc3 at MMIO 0x53ff0000 (irq = 13) is a Freescale MXC
loop: module loaded
mxc_rtc mxc_rtc.0: rtc core: registered mxc_rtc as rtc0
Probing mxc_rtc done
mc13892 rtc probe start
pmic_rtc pmic_rtc.1: rtc core: registered pmic_rtc as rtc1
mc13892 rtc probe succeed
i2c /dev entries driver
MXC WatchDog Driver 2.0
MXC Watchdog # 0 Timer: initial timeout 127 sec
MXC Watchdog: Started 10000 millisecond watchdog refresh
PMIC Character device: successfully loaded
pmic_battery: probe of pmic_battery.1 failed with error -1
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mxsdhci: MXC Secure Digital Host Controller Interface driver
mxsdhci: MXC SDHCI Controller Driver.
mmc0: SDHCI detect irq 273 irq 2 INTERNAL DMA
mxsdhci mxsdhci.1: dmabounce: registered device
mxsdhci: MXC SDHCI Controller Driver.
mmc1: SDHCI detect irq 0 irq 3 INTERNAL DMA
Registered led device: pmic_ledsr
Registered led device: pmic_ledsg
Registered led device: pmic_ledsb
Advanced Linux Sound Architecture Driver Version 1.0.20.
wm8962_i2c_probe
wm8962 1-001a: customer id 0 revision D
kernel: I papyrus:TempExceeded:temp=29:
input: WM8962 Beep Generator as /devices/virtual/i2c-adapter/i2c-1/1-001a/input/input0
No device for DAI imx-ssi-1-0
No device for DAI imx-ssi-1-1
No device for DAI imx-ssi-2-0
No device for DAI imx-ssi-2-1
DMA Sound Buffers Allocated:UseIram=0 buf->addr=7e360000 buf->area=f9e27000 size=131072
DMA Sound Buffers Allocated:UseIram=0 buf->addr=7e420000 buf->area=f9e47000 size=131072
asoc: WM8962 <-> imx-ssi-2-0 mapping ok
mmc0: queuing CIS tuple 0x01 length 3
mmc0: queuing CIS tuple 0x1a length 5
mmc0: queuing CIS tuple 0x1b length 8
mmc0: queuing CIS tuple 0x14 length 0
mmc0: queuing CIS tuple 0x80 length 1
mmc0: queuing CIS tuple 0x81 length 1
mmc0: queuing CIS tuple 0x82 length 1
mmc0: new high speed SDIO card at address 0001
input: imx-yoshi Headset as /devices/platform/soc-audio.1/sound/card0/input1
ALSA device list:
#0: imx-yoshi (WM8962)
nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
kernel: I perf:kernel:kernel_loaded=0.55 seconds:
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
regulator_init_complete: disabling TMST
regulator_init_complete: disabling VCOM
regulator_init_complete: disabling GPO4
regulator_init_complete: disabling GPO3
regulator_init_complete: disabling GPO2
regulator_init_complete: disabling GPO1
regulator_init_complete: disabling VGEN3
regulator_init_complete: disabling VGEN1
regulator_init_complete: disabling VCAM
regulator_init_complete: disabling VAUDIO
regulator_init_complete: disabling VVIDEO
regulator_init_complete: disabling VSD
regulator_init_complete: disabling SWBST
mxc_rtc mxc_rtc.0: setting system clock to 1970-01-01 01:23:44 UTC (5024)
Freeing init memory: 1076K
emmc: I def:mmcpartinfo:vendor=samsung, ddr=0, host=mmc1:
mmc1: new high speed MMC card at address 0001
mmcblk0: mmc1:0001 M4G1FA 3.72 GiB
mmcblk0: p1 p2 p3 p4
mxc_epdc_fb_init_hw: 06_05_0078_3c_159221_03_3c_00000969_85.wbf
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with writeback data mode.
EXT3 FS on mmcblk0p2, internal journal
elevator: type not found
ARC USBOTG Device Controller driver (10/08/2009)
pmic_event_subscribe: 0
USB/Charger detected
g_file_storage gadget: File-backed Storage Gadget, version: 7 August 2007
g_file_storage gadget: Number of LUNs=1
fsl-usb2-udc: bind to driver g_file_storage
fuse init (API version 7.12)
PPP generic driver version 2.4.2
input: whitney-button as /devices/platform/whitney-button/input/input2
input: zforce as /devices/platform/zforce.0/input/input3
kjournald starting. Commit interval 5 seconds
EXT3 FS on mmcblk0p3, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with writeback data mode.
wm8962_process_req
mxc_keyb: I def:drv::Keypad driver loaded
clk: Unable to get requested clock: kpp_clk
input: mxckpd as /devices/virtual/input/input4
input: mma8453 as /devices/virtual/i2c-adapter/i2c-0/0-001c/input/input5
check mma8453 chip ID
mma8453 0-001c: build time Nov 3 2011 11:21:40
add mma8453 i2c driver
EXT3 FS on mmcblk0p2, internal journal
check_portsc_bits: 0x18000205
Connected to a HIGH speed Host
g_file_storage gadget: high speed config #1
mxc_rtc: saved=0x0 boot=0x29
boot: C def:bcut:batterycut=1,version=000000:
unregistered gadget driver 'g_file_storage'
fsl-usb2-udc fsl-usb2-udc: dma_pool_destroy udc_td, fbd01000 busy
ARC USBOTG Device Controller driver unregistered
ARC USBOTG Device Controller driver (10/08/2009)
pmic_event_subscribe: 0
USB/Charger detected
usb0: MAC ee:59:00:00:00:15
usb0: HOST MAC ee:29:00:00:00:15
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
fsl-usb2-udc: bind to driver g_ether
EXT3 FS on mmcblk0p2, internal journal
check_portsc_bits: 0x18000205
Connected to a HIGH speed Host
g_ether gadget: high speed config #2: RNDIS
kernel: I papyrus:TempExceeded:temp=29:
But isn't it diags mode startup log? I think I need main mode startup log..