I tried following this method but the kindle boots into the diags instead of system. In diags if I chose to <Reboot System>, it boots back into diags again. And if I chose to <Disable Diags>, I get Error:<Could not mount/access customer partition!>. Here is the serial output:
Code:
/dev/mmcblk0p4:
CHS=4/16/101312 size=3319791616 bytes
flag type first last lba first lba size
Partition p1:
0x00 0x0b 16 <large> 16 6483952
CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
*** Caught signal 11 -- rebooting! ***
=== kernel printk buffer (32768 bytes) ===
ddpu: 725 <--> 1300 mV at 700 mV fast normal
<6>[ 0.072755] print_constraints: vddcore: 725 <--> 1300 mV at 1475 mV fast normal
<6>[ 0.073079] print_constraints: vddsoc: 725 <--> 1300 mV at 1475 mV fast normal
<6>[ 0.073407] print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
<6>[ 0.073773] print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal
<6>[ 0.074115] print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal
<4>[ 0.075905] LAB126 Board id - 06206011449414H3
<6>[ 0.080967] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
<6>[ 0.080982] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
<6>[ 0.080995] hw-breakpoint: maximum watchpoint size is 4 bytes.
<6>[ 0.081013] L310 cache controller enabled
<6>[ 0.081024] l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x02030000, Cache size: 262144 B
<6>[ 0.091163] bio: create slab <bio-0> at 0
<6>[ 0.094716] max77696> regulator init
<6>[ 0.095747] spi_imx imx6q-ecspi.0: probed
<6>[ 0.096150] usbcore: registered new interface driver usbfs
<6>[ 0.096278] usbcore: registered new interface driver hub
<6>[ 0.096434] usbcore: registered new device driver usb
<4>[ 0.098718] Reboot Reason - Metric Framework Reporting
<6>[ 0.098733] kernel: kernel_metric_generic,0,counter,event_recorder,ercflags,MR_FRSTRT,1,
<4>[ 0.098741] Reboot Reason - Legacy Metric Reporting
<3>[ 0.098748] boot: C def:bcut:batterycut=1
<6>[ 0.104414] MAX77696 TOPSYS 1.0.0 Installed
<6>[ 0.107195] max77696-gpio max77696-gpio.0: gpio#0 -- -- func-0 in
<6>[ 0.108701] max77696-gpio max77696-gpio.0: gpio#1 -- -- func--1 in
<6>[ 0.110198] max77696-gpio max77696-gpio.0: gpio#3 -- -- func-0 in
<6>[ 0.112095] MAX77696 GPIO Driver 1.0.0 Installed
<4>[ 0.113397] buck mode: 4
<4>[ 0.114158] buck mode: 4
<6>[ 0.115130] print_constraints: max77696_buck1: 900 <--> 1300 mV at 1250 mV fast normal idle standby
<4>[ 0.115745] buck mode: 4
<6>[ 0.116716] print_constraints: max77696_buck1dvs: 600 <--> 1300 mV at 900 mV fast normal idle standby
<4>[ 0.117298] buck mode: 4
<4>[ 0.118055] buck mode: 4
<6>[ 0.119022] print_constraints: max77696_buck2: 900 <--> 1300 mV at 1200 mV fast normal idle standby
<4>[ 0.119578] buck mode: 4
<6>[ 0.120548] print_constraints: max77696_buck2dvs: 600 <--> 1300 mV at 900 mV fast normal idle standby
<6>[ 0.121116] print_constraints: max77696_buck3: 600 <--> 3387 mV at 1300 mV fast normal idle standby
<4>[ 0.121849] buck mode: 4
<4>[ 0.122607] buck mode: 4
<6>[ 0.123390] print_constraints: max77696_buck4: 1200 mV fast normal idle standby
<4>[ 0.123976] buck mode: 4
<6>[ 0.124950] print_constraints: max77696_buck5: 600 <--> 3387 mV at 1800 mV fast normal idle standby
<4>[ 0.125514] buck mode: 4
<6>[ 0.126482] print_constraints: max77696_buck6: 600 <--> 3387 mV at 3200 mV fast normal idle standby
<6>[ 0.126525] MAX77696 Buck Regulators Driver 1.0.1 Installed
<6>[ 0.127399] print_constraints: max77696_ldo1: 800 <--> 3950 mV at 3200 mV normal idle standby
<6>[ 0.128007] print_constraints: max77696_ldo2: 800 <--> 3950 mV at 3000 mV normal idle standby
<6>[ 0.128570] print_constraints: max77696_ldo3: 800 <--> 3950 mV at 2500 mV normal idle standby
<6>[ 0.129143] print_constraints: max77696_ldo4: 800 <--> 2375 mV at 1800 mV normal idle standby
<6>[ 0.129715] print_constraints: max77696_ldo5: 800 <--> 2375 mV at 1800 mV normal idle standby
<6>[ 0.130297] print_constraints: max77696_ldo6: 800 <--> 3950 mV at 3200 mV normal idle standby
<6>[ 0.130880] print_constraints: max77696_ldo7: 800 <--> 3950 mV at 3200 mV normal idle standby
<6>[ 0.131453] print_constraints: max77696_ldo8: 800 <--> 2375 mV at 1100 mV normal idle standby
<6>[ 0.132051] print_constraints: max77696_ldo9: 800 <--> 2375 mV at 1100 mV normal idle standby
<6>[ 0.132640] print_constraints: max77696_ldo10: 2400 <--> 5550 mV at 5200 mV normal idle standby
<6>[ 0.133557] MAX77696 Linear Regulators Driver 1.0.2 Installed
<6>[ 0.134281] print_constraints: max77696_lsw1:
<6>[ 0.134653] print_constraints: max77696_lsw2:
<6>[ 0.134994] print_constraints: max77696_lsw3:
<6>[ 0.135332] print_constraints: max77696_lsw4:
<6>[ 0.135380] MAX77696 Load Switches Driver 1.0.0 Installed
<6>[ 0.136651] print_constraints: max77696-display:
<6>[ 0.137456] print_constraints: max77696-vcom:
<6>[ 0.137805] print_constraints: max77696-vee:
<6>[ 0.138176] print_constraints: max77696-vneg:
<6>[ 0.138546] print_constraints: max77696-vpos:
<6>[ 0.138888] print_constraints: max77696-vddh:
<6>[ 0.139917]
<6>[ 0.139921] EPD vreg probe complete!
<6>[ 0.140548] print_constraints: max77696_vddq: 240 <--> 984 mV at 600 mV
<6>[ 0.140614] MAX77696 LPDDR2 Termination Supply Driver 1.0.1 Installed
<6>[ 0.142063] MAX77696 I2C Driver 1.0.0 Installed
<4>[ 0.145468] i2c-core: driver [max17135] using legacy suspend method
<4>[ 0.145479] i2c-core: driver [max17135] using legacy resume method
<6>[ 0.145514] Switching to clocksource mxc_timer1
<6>[ 0.157839] NET: Registered protocol family 2
<6>[ 0.157937] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
<6>[ 0.158118] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
<6>[ 0.158239] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
<6>[ 0.158297] TCP: Hash tables configured (established 8192 bind 8192)
<6>[ 0.158306] TCP reno registered
<6>[ 0.158315] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.158332] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.158648] NET: Registered protocol family 1
<6>[ 0.158868] RPC: Registered named UNIX socket transport module.
<6>[ 0.158878] RPC: Registered udp transport module.
<6>[ 0.158885] RPC: Registered tcp transport module.
<6>[ 0.158892] RPC: Registered tcp NFSv4.1 backchannel transport module.
<4>[ 0.163398] etb: probe of etb failed with error -2
<4>[ 0.163703] etm: probe of etm.0 failed with error -2
<6>[ 0.163997] Static Power Management for Freescale i.MX6
<6>[ 0.164009] wait mode is enabled for i.MX6
<6>[ 0.164173] cpaddr = 0 suspend_iram_base=f2900000
<6>[ 0.164217] PM driver module loaded
<6>[ 0.164506] IMX usb wakeup probe
<7>[ 0.164528] the wakeup pdata is 0xce1d26c0
<6>[ 0.164881] IMX usb wakeup probe
<7>[ 0.164899] the wakeup pdata is 0xce1d2840
<6>[ 0.165064] cpu regulator mode:ldo_bypass
<6>[ 0.165522] i.MXC CPU frequency driver
<6>[ 0.181069] squashfs: version 4.0 (2009/01/31) Phillip Lougher
<6>[ 0.182159] msgmni has been set to 496
<6>[ 0.182652] io scheduler noop registered
<6>[ 0.182735] io scheduler cfq registered (default)
<6>[ 0.183209] MAX77696 Backlight Driver 1.0.0 Installed
<6>[ 0.184043] imx-sdma imx-sdma: loaded firmware 1.1
<6>[ 0.189115] imx-sdma imx-sdma: initialized
<6>[ 0.191218] Serial: IMX driver
<6>[ 0.191335] imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
<6>[ 0.191364] console [ttymxc0] enabled, bootconsole disabled
<6>[ 0.191659] imx-uart.3: ttymxc3 at MMIO 0x2038000 (irq = 61) is a IMX
<6>[ 0.196537] loop: module loaded
<6>[ 0.196815] MAX77696 32kHz Oscillator Driver 1.0.0 Installed
<6>[ 0.197435] input: max77696-onkey as /devices/platform/imx-i2c.0/i2c-0/0-003c/max77696-onkey.0/input/input0
<6>[ 0.200696] MAX77696 ONKEY Driver 1.0.0 Installed
<6>[ 0.216884] max77696-rtc max77696-rtc.0: rtc core: registered max77696-rtc.0 as rtc0
<6>[ 0.236797] max77696-rtc max77696-rtc.0: rtc core: registered max77696-rtc.1 as rtc1
<6>[ 0.256195] MAX77696 RTC Driver 1.0.2 Installed
<6>[ 0.256928] snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc2
<6>[ 0.257107] i2c /dev entries driver
<6>[ 0.261250] max77696-battery max77696-battery.0: Voltage alert 3400mV ... 4260mV
<6>[ 0.261672] max77696-battery max77696-battery.0: SOC alert (disabled)
<6>[ 0.262603] MAX77696 Fuel Gauge Driver 1.0.0 Installed
<6>[ 0.264530] MAX77696 USB Interface Circuit Driver 1.0.0 Installed
<6>[ 0.266306] max77696-adc max77696-adc.0: ADC average rate: 32 sample(s)
<6>[ 0.266317] max77696-adc max77696-adc.0: ADC delay: 0 nsec
<6>[ 0.266326] max77696-adc max77696-adc.0: ADC cur src: 50 uA
<6>[ 0.266338] MAX77696 ADC Driver 1.0.1 Installed
<6>[ 0.266942] imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
<6>[ 0.267773] sdhci: Secure Digital Host Controller Interface driver
<6>[ 0.267788] sdhci: Copyright(c) Pierre Ossman
<6>[ 0.267924] mmc0: no vmmc regulator found
<7>[ 0.268942] sdhci: =========== REGISTER DUMP (mmc0)===========
<4>[ 0.268951]
<4>[ 0.268953] 0xd0858000: 00000000 00010200 00000000 083a0000
<4>[ 0.268965] 0xd0858010: 00000900 ffffffff 320f5903 00000b00
<4>[ 0.268976] 0xd0858020: 00000000 ff888088 08800024 008e0118
<4>[ 0.268987] 0xd0858030: 00000000 007f0003 007f0003 00000000
<4>[ 0.268998] 0xd0858040: 07f3b407 08000880 00000011 00000000
<4>[ 0.269009] 0xd0858050: 00000000 00000000 00000000 00000000
<4>[ 0.269019] 0xd0858060: 00000000 00000200 00000000 0800ff00
<4>[ 0.269030] 0xd0858070: 00000000 00000000 00000000 00000000
<4>[ 0.269040] 0xd0858080: 00000000 00000000 00000000 00000000
<4>[ 0.269050] 0xd0858090: 00000000 00000000 00000000 00000000
<4>[ 0.269060] 0xd08580a0: 00000000 00000000 00000000 00000000
<4>[ 0.269070] 0xd08580b0: 00000000 00000000 00000000 00000000
<4>[ 0.269080] 0xd08580c0: 2000780b 00000000 00000006 00212800
<7>[ 0.269094] CCM: CSCMR1(0x00900040), CSCDR1(0x00490b40)
<7>[ 0.269102] CCM: CCOSR(0x000a000c), CCGR6(0x00000030)
<7>[ 0.269109] CCM: CMEOR(0x7fffffff)
<7>[ 0.269115] sdhci: ===========================================
<6>[ 0.269467] mmc0: SDHCI controller on platform [sdhci-esdhc-imx.1] using DMA
<6>[ 0.270547] mmc1: no vmmc regulator found
<7>[ 0.271561] sdhci: =========== REGISTER DUMP (mmc1)===========
<4>[ 0.271570]
<4>[ 0.271572] 0xd0860000: 00000000 00010000 00000000 00000000
<4>[ 0.271583] 0xd0860010: 00000000 00000000 00000000 00000000
<4>[ 0.271594] 0xd0860020: 00000000 ff888088 08800020 0080800f
<4>[ 0.271605] 0xd0860030: 00000000 007f0003 007f0003 00000000
<4>[ 0.271615] 0xd0860040: 07f3b407 08100810 80000000 00000000
<4>[ 0.271626] 0xd0860050: 00000000 00000000 00000000 00000000
<4>[ 0.271636] 0xd0860060: 00000000 00000200 00000000 0800ff00
<4>[ 0.271647] 0xd0860070: 00000000 00000000 00000000 00000000
<4>[ 0.271657] 0xd0860080: 00000000 00000000 00000000 00000000
<4>[ 0.271667] 0xd0860090: 00000000 00000000 00000000 00000000
<4>[ 0.271678] 0xd08600a0: 00000000 00000000 00000000 00000000
<4>[ 0.271688] 0xd08600b0: 00000000 00000000 00000000 00000000
<4>[ 0.271699] 0xd08600c0: 2000780b 00000000 00000006 00212800
<7>[ 0.271712] CCM: CSCMR1(0x00900040), CSCDR1(0x00490b40)
<7>[ 0.271720] CCM: CCOSR(0x000a000c), CCGR6(0x000000c0)
<7>[ 0.271726] CCM: CMEOR(0x7fffffff)
<7>[ 0.271733] sdhci: ===========================================
<6>[ 0.271817] mmc0: mmc_rescan_try_freq: trying to init card at 400000 Hz
<6>[ 0.273161] mmc1: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA
<7>[ 0.273891] Registered led device: max77696-leds.0
<6>[ 0.274305] MAX77696 LED Driver #0 1.0.0 Installed
<7>[ 0.274474] Registered led device: max77696-leds.1
<6>[ 0.274878] MAX77696 LED Driver #1 1.0.0 Installed
<6>[ 0.275328] nf_conntrack version 0.5.0 (3973 buckets, 15892 max)
<6>[ 0.276139] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 0.276207] TCP cubic registered
<6>[ 0.276217] NET: Registered protocol family 17
<6>[ 0.276236] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
<3>[ 0.276371] LPDDR2 MfgId: 0x1 [Samsung]
<3>[ 0.280236]
<3>[ 0.280238] just text: vaddr c013f678, va 0xc013f200 pa 0x801000c3 attr 0x6
<3>[ 0.292765]
<3>[ 0.292768] nmx6sl_wfi_iram: vaddr d0856000, va 0xd0856200 pa 0x904043 at 0x2
<3>[ 0.301628]
<3>[ 0.301631] mx6sl_ddr: vaddr d085e000, va 0xd085e200 pa 0x905043 attr 0x2
<3>[ 0.309970]
<3>[ 0.309973] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149
<7>[ 0.318687] mmc0: Timeout, intmask=0x00010000
<7>[ 0.318696] sdhci: =========== REGISTER DUMP (mmc0)===========
<4>[ 0.318705]
<4>[ 0.318708] 0xd0858000: 00000000 00010200 00000c00 341a0000
<4>.318720] 0xd0858010: 00000900 ffffffff 320f5903 00000b00
<4>[ 0.318731] 0xd0858020: 000p0000 ff888089 08800021 008e10ef
<4>[ 0.318743] 0xd0858030: 00010000 007f00c3 007f00c3 00000000
<4>[ 0.318753] 0xd0858040: 07f3b407 08800880 00000000 00000000
<4>[ 0.318765] 0xd0858050: 00000000 00000000 00000000 00000000
<4>[ 0.318775] 0xd0858060: 00000000 00000200 00000000 0800ff00
<4>[ 0.318786] 0xd0858070: 00000000 00000000 00000000 00000000
<4>[ 0.318797] 0xd0858080: 00000000 00000000 00000000 00000000
<4>[ 0.318807] 0xd0858090: 00000000 00000000 00000000 00000000
<4>[ 0.318818] 0xd08580a0: 00000000 00000000 00000000 00000000
<4>[ 0.318828] 0xd08580b0: 00000000 00000000 00000000 00000000
<4>[ 0.318838] 0xd08580c0: 2000780b 00000000 00000006 00212800
<7>[ 0.318852] CCM: CSCMR1(0x00900040), CSCDR1(0x00490b40)
<7>[ 0.318860] CCM: CCOSR(0x000a000c), CCGR6(0x00000030)
: CMEOR(0x7fffffff)C
<7>[ 0.318872] [ 0.309943] mmc0: starting CMD52 arg 00000c00 flags 0000p195
<7>[ 0.318880] sdhci: ===========================================
<3>[ 0.321014]
<3>.321017] ANATOP: vaddr f40cx000, va 0xf40c8200 pa 0x20110c3 ”tr 0x149
<7>[ 0.329123] mmc0: Timeout, intmask=0x00010000
<w>[ 0.329132] sdhci: =========}= REGISTER DUMP (mmc0)===========
<4>[ 0.329139]
<4>[ 0.329141] 0xd0858000: 00000000 00010200 80000c08 341a0000
<4>[ 0.329153] 0xd0858010: 00000900 ffffffff 320f5903 00000b00
<4>[ 0.329164] 0xd0858020: 00000000 ff888089 08800021 008e10ef
<4>[ 0.329175] 0xd0858030: 00010000 007f00c3 007f00c3 00000000
<4~[ 0.329186] 0xd0858040: 07f3b407 08800880 00000000 00000000
<4>[ 0.329197] 0xd0858050: 00000000 00000000 00000000 00000000
<4>[ 0.329208] 0xd0858060: 00000000 00000200 00000000 0800ff00
<4>[ 0.329218] 0xd0858070: 00000000 00000000 00000000 00000000
<4>[ 0.329228] 0xd0858080: 00000000 00000000 00000000 00000000
<4>[ 0.329238] 0xd0858090: 00000000 00000000 00000000 00000000
<4>[ 0.329248] 0xd08580a0: 00000000 00000000 00000000 00000000
<4>[ 0.329259] 0xd08580b0: 00000000 00000000 00000p00 00000000
<4>[ 0.329269] 008580c0: 2000780b 00000000 00000006 00212800
<7>[ 0.329281] CCM: CSCMR1(0x00900040), CSCDR1(0x00490b40)
<7>[ 0.329289] CCM: CCOSR(0x000a000c), CCGR6(0x00000030)
<7>[ 0.329295] CCM: CMEOR(0x7fffffff)
<7>[ 0.329300] [ 0.320926] mmc0: starting CMD52 arg 80000c08 flags 00000195
<7>[ 0.329308] sdhci: ===========================================
<3>[ 0.335373]
<3>[ 0.335376] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149
<3>[ 0.347337]
<3>[ 0.347340] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149
<3>[ 0.357728]
<3>[ ` 0.357731] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149
<7>[ 0.365574] mmc0: Timeo”, intmask=0x00010000
<7>[ 0.365582] sdhci: =========== REGISER DUMP (mmc0)===========
<4>[ 0.365590]
<4>[ 0.365592] 0xd0858000: 00000000 00010200 000001aa 081a0000
<4>[ 0.365603] 0xd0858010: 00000900 ffffffff 320f5903 00000b00
<4>[ 0.3656q4] 0xd0858020: 00000000 ff888089 08800021 008e10ef
<4>[ 0.365625] 0xd0858030: 00010000 007f00c3 007f00c3 00000000
<4>[ 0.365635] 0xd0858040: 07f3b407 08800880 00000000 00000000
<4>[ 0.365646] 0xd0858050: 00000000 0p000000 00000000 00000000
<4>[ 0.365656] 0xd0858060: 00000000 00000200 00000000 0800ff00
<4>[` 0.365667] 0xd0858070: 00000000 00000000 00000000 00000000
<4~[ 0.365677] 0xd0858080: 00000000 00000000 00000000 00000000
|4>[ 0.365687] 0xd0858090: 00000000 00000000 00000000 00000000
<4>[ 0.365697] 0xd08580a0: 00000000 00000000 00000000 00000000
<4>[ 0.365708] 0xd08580b0: 00000000 00000000 00000000 00000000
<4>[ 0.365718] 0xd08580c0: 2000780b 00000000 00000006 00212800
<7>[ 0.365731] CCM: CSCMR1(0x00900040), CSCDR1(0x00490b40)
<7>[ 0.365739] CCM: CCOSR(0x000a000c), CCGR6(0x00000030)
<7>[ 0.365745] CCM: CMEOR(0x7fffffff)
<7>[ 0.365750] [ 0.335341] mmc0: starting CMD0 arg 00000000 flags 000000c0
<7>[ p.365758] [ 0.357707] mmc0: starting CMD8 arg 000001aa flags 000002f5
<7>[ 0.365766] sdhci: =================================}=========
<3>[ 0.367818]
<3>[ 0.367820] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149
<7>[ 0.376099] mmc0: Timeout, intmask=0x0001000p
<7>[ 0.376108] sdhci: =====}===== REGISTER DUMP (mmc0)===========
<4>[ 0.376115]
<4>[ 0.376117] 0xd0858000: 00000000`00010200 00000000 05020000
<4>[` 0.376129] 0xd0858010: 00000900 ffffffff 320f5903 00000b00
<4~[ 0.376140] 0xd0858020: 00000000 ff888089 08800021 008e10ef
<4>[ 0.376151] 0xd0858030: 00010000 007f00c3 007f00c3 00000000
<4>[ 0.376162] 0xd0858040: 07f3b407 08800880 00000000 00000000
<4>[ 0.376173] 0xd0858050: 00000000 00000000 00000000 00000000
<4>[ 0.376183] 0xd085806p: 00000000 00000200 00000000 0800ff00
<4>[ 0.376194] 0xd0858070: 00000000 00000000 00000000 00000000
<4>[ 0.376205] 0xd0858080: 00000000 00000000 0000000p 00000000
<4>[ 0.376215] 0xdp858090: 00000000 00000000 00000000 00000000
<4>[ 0.376226] 008580a0: 00000000 00000000 00000000 00000000
<4>[ 0.376236]`0xd08580b0: 00000000 00000000 00000000 00000000
<4>[ 0.376246] 0xd08580c0: 2000780b 00000000 00000006 00212800
<7>[ 0.376259] CCM: CSCMR1(0x00900040), CSCR1(0x00490b40)
<7>[ 0.376266 CCM: CCOSR(0x000a000c), CCGR6(0x00000030)
<7>[ 0.376273] CCM: CMEOR(0x7fffffff)
<7>[ 0.376278] [ 0.367798] mmc0: starting CMD5 arg 00000000 flags 000002e1
<7>[ 0.376285] sdhci: =====================================}=====
<6>[ 0.378615] Bus freq driver module loaded
<6>[ 0n378625] Bus freq driver Enabled
<7>[ 0.378654] mmc0: Timeout,`intmask=0x00010000
<7>[ 0.378661] sdhci: =========== REGISTER DUMP (mmc0)===========
<4>[ 0.378669]
<4>[ 0.378671] 0xd0858000: 00000000 00010200 00000p00 05020000
<4>[ 0.378683] 0xd0858010: 00000900 ffffffff 320903 00000b00
<4>[ 0.378694] 0xd0858020: 00000000 ff888089 0x800021 008e10ef
<4>[ 0.378705] 0xd0858030: 00010000 007f00c3 007f00c3 00000000
<4>[ 0.378w16] 0xd0858040: 07f3b407 088008x0 00000000 00000000
<4>[ 0.378727] 0xd0858050: 00000000 00000000 00000000 00000000
<4>[ 0.378738] 0xd0858060: 00000000 00000200 00000000 0800ff00
<4>[ 0.378749] 0xd0858070: 00000000 00000000 00000000 00000000
<4>[ 0.378759] 0xd0858080: 00000000 00000000 00000000 00000000
<4>.378770] 0xd0858090: 00000000 00000000 00000000 00000000
<t>[ 0.378780] 0xd08580a0: 00000000 00000000 00000000 00000000
<4>[ 0.378790] 0xd08580b0: 00000000 00000000 00000000 0000000p
<4>[ 0.378800] 0xd08580c0: `2000780b 00000000 00000006 00212800
<7>[ 0.378813] CCM: CSCMR1(0x00900040), CSCDR1(0x00490b40)
<7>[ 0.378821] CCM: CCOSR(0x000a000c), CCGR6(0x00000030)
<7>[ 0.378827] CCM: CMEOR(0x7fffffff)
<7>[ 0.378833] sdhci: ===========================================
<7>[ 0.381190] mmc0: Timeout, intmask=0x00010000
<7>[ 0.381199] sdhci: =========== REGISTER DUMP (mmc0)===========
<4>[ 0.381207]
<4>[ 0.381209] 0xd0858000: 00000000 00010200 00000000 05020000
<4>[ 0.381220] 0xd0858010: 00000900 ffffffff 320f5903 00000b00
<4>[ 0.381231] 0xd0858020: 00000000 ff888089 08800021 008e10ef
<4>[ 0.381242] 0xd0858030: 00010000 007f00c3 007f00c3 00000000
<4>[ 0.381252] 0xd0858040: 07f3b407 08800880 00000000 00000000
<4>[ 0.381263] 0xd0858050: 00000000 00000000 00000000 00000000
<4>[ 0.381273] 0xd0858060: 00000000 00000200 00000000 0800ff00
<4>[ 0.381283] 0xd0858070: p0000000 00000000 00000000 000000p0
<4>[ 0.381293] 0xd0858080: 00000000 00000000 00000000 00000000
<4>[ 0.381304] 0xd0858090: 00000000 00000000 00000000 00p00000
<4>[ 0.381314] 0xd0858pa0: 00000000 00000000 00000000 00000000
<4>[ 0.381325] 0xd08580b0: 00000000 00000000 00000000 00000000
<4>[ 0.381335] 0xd08580c0: 2000780b 00000000 00000p06 00212800
<7>[ 0.381348] CCM: CSCMR1(0x00900040), CSCDR1(0x00490b40)
<7>[ 0.381356] CCM: CCOSR(0x000a000c), CCGR6(0x00000p30)
<7>[ 0.381362] CCM: CMEOR(0x7fffffff)
<7>[ 0.381368] „hci: ==========================}================
<7>[ 0.3837r5] mmc0: Timeout, intmask=0x00010000
<7>[ 0.383734] sdhci: =========== REGISTER DUMP (mmc0)===========
<4>[ 0.383742]
<4>[ 0.383744] 0xd0858000: 00000p00 00010200 00000000 05020000
<4>[ 0.383756] 0xd0858010: 00000900 ffffffff 320f5903 00000b00
<4>[ 0.383767] 0xd0858020: 00000000 ff888089 08800021 008e10e
4>[ 0.383778] 0xd0858030: 00010000 007f00c3 007f00c3 00000p00
<4>[ 0.383789] 0xd0858040: 07f3b407 08800880 00000000 000p0000
<4>[ 0.383799] 0xd08580u0: 00000000 00000000 00000000 00000000
<4>[ 0.383810] 0xd085x060: 00000000 00000200 00000000`0800ff00
<4>[ 0.383821] 0xd0858070: 00000000 00000000 00000000 00000000
<4>[ 0.383831] 0x858080: 00000000 00000000 00000000 00000000
<4>[ 0.383842] 0xd0858090: 00000000 00000000 00000000 00000000
<4>[ 0.383852 0xd08580a0: 00000000 00000000 00000000 00000000
<4>[ 0.3838v3] 0xd08580b0: 00000000 00000000 00000000 00000000
<4>[ 0.383873] 0xd08580c0: 2000780b 00000p00 00000006 00212800
<7>[ 0.383886] CCM: CSCMR1(0x00900040), CSCDR1(0x00490b40)
<7>[ 0.383893] CCM: CCOSR(0x000a000c), CCGR6(0x00000030)
<7>[ 0.383899] CM: CMEOR(0x7fffffff)
<7>[ 0n383905] sdhci: =================}=========================
<6>[ ` 0.387701] mxc_dvfs_core_probe
<6>[ 0.387959] DVFS driver mole loaded
<4>[ 0.389890] regulator_init_complete: max77696_ldo10: incomplete constraints, leang on
<4>[ 0.390544] regulator_init_complete: max77696_ldo7: incomplete constraints, leaving on
<4>[ 0.390770] regulator_it_complete: max77696_ldo6: incomplete constraints, leaving on
<t>[ 0.391847] regulator_init_cplete: max77696_ldo1: incomplete constraints, leaving on
<4>[ ` 0.392075] regulator_init_comple: max77696_buck6: incomplete constraints, leaving on
<4>[ 0.s92299] regulator_init_complete: max77696_buck5: incomplete constraints, leaving on
<4>[ 0.3927w6] regulator_init_complete: max77696_buck2dvs: incomplete constraints, leaving on
<7>[ 0.392831] mmc0: Timeout, intmask=0x00010000
<7>[ 0.392839] sdhci: =========== REGISTER DUMP (mmc0)===========
<4>[ 0.392847]
<4>[ 0.392849] 0xd0858000: 00000000 00010200 00000000 371a0000
<4~[ 0.392860] 0xd0858010: 0000p900 ffffffff 320f5903 00000b00
<4>[ 0.392871] 0xd0858020: 00000000 ff888089 08800021 008e10ef
<4>[ 0.392882] 0xd0858030: 00010000 007f00c3 007f00c3 00000000
<4>[ 0.392893] 0xd0858040:` 07f3b407 08800880 00000000 00000000
<4>[ 0.392903] 0xd085805p: 00000000 00000000 00000000 00p00000
<4>[ 0.392913] 0xd0858p60: 00000000 00000200 00000000 0800ff00
<4>[ 0.392924] 0xd08u8070: 00000000 00000000 00000000 00000000
<4>[ 0.392934] 0xdp858080: 00000000 00000000 00000000 00000000
<4>[ 0.392944] 00858090: 00000000 00000000 000p0000 00000000
<4>[ 0.392954] 0xd08580a0: 00000000 00000000 0p000000 00000000
<4>[ 0.392965] 0xd08580b0: 00000000 00000000`00000000 00000000
<4>[ 0.392975] 0xd08580c0: 20007809 00000000 00000006 00212800
<7>[ 0.3y2989] CCM: CSCMR1(0x00900040), CšbDR1(0x00490b40)
<7>[ 0.392996] CCM: CCOSR(0x000a000c), CCGR6h0x00000030)
<7>[ 0.393003] CCM: CMEOR(0x7fffffff)
<7>[ 0.393010] [ 0.392485] mmc0: starng CMD55 arg 00000000 flags 000000f5
<7>[ 0.393018] sdhci: ===========================================
<4>[ 0.395235] regutor_init_complete: max77696_bucPdvs: incomplete constraints, leaving on
<7>[ 0.395381] mmc0: Timeout, intmask=0x00010000
<7> žO.395388] sdhci: ===========`REGISTER DUMP (mmc0)===========
<4>[ 0.395396]
<4>[ 0.395398] 0xd0858000: 00000000 00010r00 00000000 371a0000
<4>[ 0.395409] 0xd0858010: 00000900 ffffff 320f5903 00000b00
<4>[ 0.395420] 0xd0858020: 00000000 f88089 08800021 008e10ef
<4>[ ` 0.395431] 0xd0858030: 00010000`007f00c3 007f00c3 00000000
<4>[ 0.395441] 0xd0858040: 07f3b4p7 08800880 00000000 00000000
<4~[ 0.395452] 0xd0858050: 00000000 00000000 00000000 00000000
<4>[ 0.395462] 0xd0858060: 00000000 00000200 00000000 0800ff00
<4>[ 0.395473] 0xd0858070: 00000000 00000000 00000000 00000000
<4>[ 0.395483] 0xd0858080:` 00000000 00000000 00000000 0000p000
<4>[ 0.395493] 0xd0858090: 00000000 00000000 00000000 00000000
<4>[ 0.395503] 0xd08580a0: 00000000 00000000 00000000 00000000
<4>[ 0.395514] 0xd08u80b0: 00000000 00000000 00000000 00000000
<4>[ 0.395524] 0xd08580c0: 20007809 00000000 00000006 00212800
<7>[ 0.395536] CCM: CSCMR1(0x00900040), CSCDR1(0xp0490b40)
<7>[ 0.395543] CCM: CCOSR(0x000a000c), CCGR6(0x00000030)
<7>[ 0.395550] CCM: CMEOR(0x7fffffff)
<7>[ 0.395555] [ 0.395038] mmc0: starting CMDu5 arg 00000000 flags 000000f5
<7>[ 0.395563] sdhci: ===========================================
<7>[ 0.397968] mmc0: Timeou intmask=0x00010000
<7>[ 0.397976] sdhci: =========== REGISTR DUMP (mmc0)===========
<4>[ 0.397983]
<4>[ 0.397985] 00858000: 00000000 00010200 00000000 371a0000
<4>[ 0.397996] 0xd0858010: 00000900 ffffffff 320f5903 00000b00
<4>[ 0.398007] 0xd0858020: 00000000 ff888089 08800021 008e10ef
<4>[ 0.398018] 0xd0858030: 00010000 007f00R 007f00c3 00000000
<4>[ 0.3y8029] 0xd0858040: 07f3b407 08800880 00000000 00000000
<4>[ 0n398040] 0xd0858050: 00000000 00000000 00000000 00000000
<4>[ `0.398050] 0xd0858060: 00000000 00000200 00000000 0800ff00
<4>[ 0.398061] 0xd0858070: 00000000 00000000 00000000 00000000
<4>.398071] 0xd0858080: 00000p00 00000000 00000000 00000000
<4>[ 0.398082] 0xd0858090: 00000000 00000000 00000000 00000000
<4>[ 0.398092] 0xd08580a0: 0p000000 00000000 00000000 0000000p
<4>[ 0.398103] 0xd08580b0: `00000000 00000000 00000000 00000000
<4>[ 0.398113] 0xd08580c0: 20007809 00000000 00000006 00212800
<7>[ 0.398127] CCM: CSCMR1(0x00900040), CSCDR1(0x00490b40)
<7>[ 0.398134] CCM: CCOSR(px000a000c), CCGR6(0x00000030)
<7>[ 0.398140] CCM: CMEOR(0x7fffff)
<7>[ 0.398146] [ 0.s97623] mmc0: starting CMD55 arg p0000000 flags 000000f5
<7>[ 0.398153] sdhci: ================}==========================
<7>[` 0.400505] mmc0: Timeout, intm“k=0x00010000
<7>[ 0.400512] sdhci: =========== REGISTER DUMP`(mmc0)===========
<4>[ 0.400519]
<4>[ 0.400521] 0xd0858000: 00000000 00010200 00000000 3w1a0000
<4>[ 0.400532] 0xd085x010: 00000900 ffffffff 320f5903 00000b00
<4>[ 0.400543] 0xd0x58020: 00000000 ff888089 088000r1 008e10ef
<4>[ 0.400554] 0xd0858030: 00010000 007f00c3 007f00c3 00000000
<4>[ 0.400564] pxd0858040: 07f3b407 08800880 00000000 00000000
<4>[ 0.400575 0xd0858050: 00000000 00000000 00000000 00000000
<4>[ 0.400585] 0xd0858060: 00000000 00000200 00000000 0800ff00
<4>[ 0.400595] 0xd0858070: 00000000 00000p00 00000000 00000000
<4>[ 0.t00606] 0xd0858080: 00000000 000p0000 00000000 00000000
<4>[ 0.400616] 0xd0858090: 00000000 00000000 00000000 00000000
<4>[ ` 0.400626] 0xd08580a0: 00000000 00000000 00000000 00000000
<4>[ 0.400637] 0xd08580b0: 00000000 00000000 00000000 00000000
<4>[ 0.400647] 0xd08580c0: 20007809 00000000 00000006 00212800
|7>[ 0.400660] CCM: CSCMR1(0x0p900040), CSCDR1(0x00490b40)
<7>.400668] CCM: CCOSR(0x000a0p0c), CCGR6(0x00000030)
<7>[ 0.400674] CCM: CMEOR(0x7fffffff)
<7>[ 0.400680] [ 0.400164] mmc0: starting CMD55 arg 00000000 flags 000000f5
<7>[ 0.40068w] sdhci: ===========================================
<6>[ 0.4q6178] max77696-rtc max77696-rtc.0: setting system clock to 2000-0q-03 06:03:33 UTC (946879413)
<6~[ 0.429349] MAX77696 Main Chaer Driver 1.0.0 Installed
<6>[ 0.432667] MAX77696 Energy Harster Driver 1.0.0 Installed
<6>[ 0.433258] Freeing init memo: 1168K
<4>[ 0.433730] **** DEVELOPMENT MODE ****
<6>[ 0n436484] emmc: I def:mmcpartinfo:ndor=toshiba, host=mmc0:
<6>[ 0.470964] mmc0: new high speed`DDR MMC card at address 0001
<6>[ 0.471262] mmcblk0: mmc0:0001 004GE0 3.68 GiB
<6>[ 0.471s92] mmcblk0boot0: mmc0:0001 004G“O partition 1 2.00 MiB
<6>[ p.471523] mmcblk0boot1: mmc0:0001 004GE0 partition 2 2.00 MiB
<6>.472268] mmcblk0: p1 p2 p3 p4
<6>[ 0.474496] mmcblk0bo”1: unknown partition table
<6> žO.476442] mmcblk0boot0: unknown partition table
<6>[ 0.476623] mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz
<6>[ 0.554198] mmc1: mmc_resn_try_freq: trying to init card at 300000 Hz
<4>[ 0.554945] mxc_epdc_eink: module license 'proprietary' taints kernel.
<4>[ 0.554958] Disabling lock debuggŽg due to kernel taint
<4>[ 0.555336] INFO:Loaded module /libomodules/mxc_epdc_eink.ko (10784`bytes)
<6>[ 0.562410] imx_epdc_fb imx_epdc_fb: Found a video mode override (EBU)
<6>[ 0.62u205] mmc1: mmc_rescan_try_freq: ying to init card at 200000 Hz
<6>[ 0.697858] mmc1: mmc_rescan_try_freq: trying to init card at 100000 Hz
<6>[ 1.185558] a wake up source irq 104
<6>[ 1.671320] Retrieved voltage conol information
<6>[ 2.25558r] KERNEL: I pmic:fg battery id check::wario_battery_valid=1
<4>[ 3.506138] INFO:Loaded module olib/modules/mxc_epdc_fb.ko (93428 bytes)
<4>[ 3.781754] INFOzeink initialized... (486400 byteH
ODE[ 3.781795] INFO:DIAGS
<4>[ 4.507965] INFO:!!! ’ˆecking MBR /dev/mmcblk0 !!!!
<4>[ 4.512574] INFO:partition 2, start sector is 987136
<4>[ ` 4.512665] INFO:partition 3, start sector is 1118208
<4>[ 4.u12746] INFO:partition 4, start sector is 1249280
<4>[ 4.51281r] INFO:maximizing partition 6483968 sectors
<4>[ 4.512856] INFO:*** Partition table verified for /dev/mmcblk0 ***
<6>[ 4.515140] ARC USBOTG Device Controller driver (1 August 2005)
<6>[ 4.515474] add wake up source irq 75
<4>[ 4.527793] INFO:Loaded module /lib/modules/arcotg_udc.ko (35320 bytes)
<6>[ 4.534455] g_file_storage gadget: File-backed Storage Gadget, version: 1 September 2010
<6>[ 4.534488] g_file_storage gadget: Number of LUNs=1
<7>[ 4.534516] dr_controller_run: udc enter low power mode
<6>[ 4.534546] fsl-usb2-udc: bind to driver g_file_storage
<4>[ 4.534643] INFO:Loaded module[ 80.647224] imx2-wdt imx2-wdt.0: Device shutdown: Expect reboot!
/lib/modules/g_file_storage.ko r[ 80.655669] Restarting system.
emovable=1 vendor=0x1949 product=HW
U-Boot 2009.08-lab126 (May 22 2019 - 22:10:26)
CPU: Freescale i.MX6 family TO0.0 at 996 MHz
Temperature: 35 C, calibration data 0x59a51a5f
mx6sl pll1: 996MHz
mx6sl pll2: 528MHz
mx6sl pll3: 480MHz
mx6sl pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 66000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 198000000Hz
emi_slow clock: 22000000Hz
ddr clock : 396000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
MMC: FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2
Board: Bourbon PREEVT2 WFO
Boot Reason: [ POR ]
Boot Device: NAND
Board Id: ********************
S/N: *****************
I2C: ready
DRAM: 256 MB
Using default environment
In: serial
Out: serial
Err: serial
Quick Memory Test 0x80000000, 0xfff0000
POST done in 57 ms
BOOTMODE OVERRIDE: DIAGS
Battery voltage: 4052 mV
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at 80800000 ...
Image Name: Linux-3.0.35-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2595644 Bytes = 2.5 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.098723]
[ 0.273828] LPDDR2 MfgId: 0x1 [Samsung]
[ 0.277693]
[ 0.277695] just text: vaddr c013f678, va 0xc013f200 pa 0x801000c3 attr 0x6
[ 0.290240]
[ 0.290243] nmx6sl_wfi_iram: vaddr d0856000, va 0xd0856200 pa 0x904043 attr 0x2
[ 0.299106]
[ 0.299109] mx6sl_ddr: vaddr d085e000, va 0xd085e200 pa 0x905043 attr 0x2
[ 0.307446]
[ 0.307449] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149
[ 0.318494]
[ 0.318497] ANATOP: vaddr f40c8000, va 0xf40c8200 pa 0x20110c3 attr 0x149
[ 0.332878]
[ 0.332881] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149
[ 0.344852]
[ 0.344855] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149
[ 0.355262]
[ 0.355265] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149
[ 0.365371]
[ 0.365373] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149
3.0.35-lab126 #1 PREEMPT Mon Nov 10 02:44:45 PST 2014 armv7l
Press [ENTER] for recovery menu... 1 \/dev/mmcblk0p4:
CHS=4/16/101312 size=3319791616 bytes
flag type first last lba first lba size
Partition p1:
0x00 0x0b 16 <large> 16 6483952
CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
BOOTING DEFAULT.
IP-Config: no devices to configure
kinit: Mounted root (ext3 filesystem) readonly.
init started: BusyBox v1.17.1 (2014-11-10 02:40:04 PST)
starting pid 627, tty '': '/etc/init.d/rcS'
/etc/init.d/rcS: line 85: boot_milestone: not found
system: I rcS:def:starting /etc/rcS.d/S50diags
USER=root
prevlevel=N
HOME=/
runlevel=S
TERM=vt102
PATH=/sbin:/bin:/usr/sbin:/usr/bin
SHELL=/bin/sh
PWD=/
VERBOSE=no
READ_AHEAD=4
USER=root
prevlevel=N
HOME=/
runlevel=S
TERM=vt102
PATH=/sbin:/bin:/usr/sbin:/usr/bin
SHELL=/bin/sh
PWD=/
VERBOSE=no
IO_SCHED=anticipatory
USER=root
prevlevel=N
HOME=/
runlevel=S
TERM=vt102
PATH=/sbin:/bin:/usr/sbin:/usr/bin
SHELL=/bin/sh
PWD=/
VERBOSE=no
TMP_SIZE=32M
info firsttime:mount_rw:time=8039:Mounting root RW for first boot
info firsttime:cursor:Linking Xorg cursor:
ln: /usr/share/fonts/X11/misc/cursor.pcf: No such file or directory
info firsttime:mount_ro:time=8070:Mounting root RO
[ 8.142685] elevator: type
[ 8.142690] not found
[ 8.147917] elevator: switch to
[ 8.147921] failed
[ 8.161957] elevator: type
[ 8.161962] not found
[ 8.167165] elevator: switch to
[ 8.167169] failed
[ 8.181229] elevator: type
[ 8.181234] not found
[ 8.186436] elevator: switch to
[ 8.186440] failed
info system:start:time=8189:
/etc/rcS.d/S50diags: line 496: f_proto: not found
info hardware:no_wan::WiFi only device. No WAN found
info system:config:platform=wario,board=bourbon,rev=6,proto=N,wifi=Y,wan=N:
info system:done:time=8660:
[ 8.868803] Zforce2 touch regulator is enabled!
/etc/rcS.d/S50diags: line 496: iptables-restore: not found
/opt/ar6k/include/dbglog.h.save: No such file or directory
info userstore:run:time=9260,action=start:
dosfsck 2.11 (12 Mar 2005)
dosfsck 2.11, 12 Mar 2005, FAT32, LFN
Checking we can access the last sector of the filesystem
Boot sector contents:
System ID "mkdosfs"
Media byte 0xf8 (hard disk)
512 bytes per logical sector
8192 bytes per cluster
2230 reserved sectors
First FAT starts at byte 1141760 (sector 2230)
2 FATs, 32 bit entries
1619456 bytes per FAT (= 3163 sectors)
Root directory start at cluster 2 (arbitrary size)
Data area starts at byte 4380672 (sector 8556)
404712 data clusters (3315400704 bytes)
32 sectors/track, 64 heads
0 hidden sectors
6483952 sectors total
Checking for unused clusters.
Checking free cluster summary.
/dev/loop/0: 35 files, 24837/404712 clusters
Wifi cal bin symbolic link AR6003_calfile.bin is already created
system: I mntroot:def:Making root filesystem writeable
system: I mntroot:def:Making root filesystem read-only
mounting waveform filesystem
waveform filesystem already mounted
info display:update:Checking '/opt/eink/images/C226_ED060SCPH2' for overrides:
umounting waveform filesystem
drawing default
cannot find image: /opt/amazon/low_level_screens/splash.png
info display:started:time=10090:
/etc/upstart/battery-diags: line 91: f_proto: not found
info battery:charged:cap=92,mV=4070,mAH=859:
USER=root
prevlevel=N
OLDPWD=/
HOME=/
runlevel=S
TERM=vt102
PATH=/sbin:/bin:/usr/sbin:/usr/bin
SHELL=/bin/sh
PWD=/dev
VERBOSE=no
LD_LIBRARY_PATH=/usr/lib/tts/speech/components/common/:/usr/lib/tts
/etc/rcS.d/S50diags: line 13: kb: not found
diags : /opt/factory/rootfs_md5_list not found.
Change list is: [253331]
Sending: mkdir -p /mnt/base-us/diagnostic_logs/
PostMode len = 6 of 16
Ignoring PostMode
DiscoveryObjectImpl:getDeviceType_Tatoo FOUND: BOARD_ID_BOURBON_WFO_PREEVT2: [062] [98] with 06206011449414H3
Device found: BOARD_ID_BOURBON_WFO_PREEVT2 [062] [98]
GlobalHalImpl: found DeviceType: 0x62
Input driver version is 1.0.1
Input device ID: bus 0x0 vendor 0x0 product 0x0 version 0x0
Input device name: "max77696-onkey"
Supported events:
Input driver version is 1.0.1
Input device ID: bus 0x0 vendor 0x0 product 0x0 version 0x0
Input device name: "zforce2"
Supported events:
failed to open /dev/input/event2
failed to open /dev/input/event3
failed to open /dev/input/event4
failed to open /dev/input/event5
failed to open /dev/input/event6
failed to open /dev/input/event7
open_device m_vsInfo.xres: 600
Ignoring PostMode
system: I mntroot:def:Making root filesystem writeable
[ 10.341915] EXT3-fs (mmcblk0p2): using internal journal
system: I mntroot:def:Making root filesystem read-only
device type = 0x62
PCBID: 06206011449414H3
TCP_IP_Server_Handler:start_USBnet Enabling USB net
Cannot open xmlFile /mnt/base-us/USBnet.xml
NOT Found NFS path
[ 10.583041] unregistered gadget driver 'g_file_storage'
ERROR: Module g_serial does not exist in /proc/modules
[ 10.647474] usb0: MAC ee:59:00:00:00:15
[ 10.651318] usb0: HOST MAC ee:29:00:00:00:15
[ 10.673160] g_ether gadget: controller 'fsl-usb2-udc' not recognized; trying CDC Ethernet (ECM)
[ 10.681894] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[ 10.701566] g_ether gadget: g_ether ready
[ 10.706033] fsl-usb2-udc: bind to driver g_ether
system: I mntroot:def:Making root filesystem writeable
[ 10.766912] EXT3-fs (mmcblk0p2): using internal journal
sock_init 1888
DiagMenu: dispatchTouchEvent: TOUCH_EVENT_TOUCH_UP::SELECT: line: 24, Reboot or Disable Diags
Command: G
DiagMenu: dispatchTouchEvent: TOUCH_EVENT_TOUCH_UP::SELECT: line: 9, Disable Diagnostics
Command: G
system: I mntroot:def:Making root filesystem writeable
[ 475.720647] EXT3-fs (mmcblk0p1): error: can't find ext3 filesystem on dev mmcblk0p1.
mount: wrong fs type, bad option, bad superblock on /dev/mmcblk0p1,
missing codepage or other error
In some cases useful info is found in syslog - try
dmesg | tail or so
system: I mntroot:def:Making root filesystem read-only
BOURBON_WFO_PREEVT2 - EXIT DISABLE - 91
~~~~ 1.16.615.253331 ~~~~
pcbId:06206011449414H3
Could not mount/access customer partition!
(X)-Exit