Hi, I hope this thread isn't too old to even get a reply to this.
I have a very similar issue to the one described by bingofuel in post #19 on this thread. I have followed Adonis's guide in post #17 aswell.
I originally had a "BATTERY INVALID -22" error, replacing the battery also did not fix this.
I got the diags_kernel.img and mmcblk0p1.bin files from this thread's post #4:
https://www.mobileread.com/forums/sh...d.php?t=348137
After flashing the diags_kernel.img and mmcblk0p1.bin via fastboot and rebooting, now the kindle won't even boot to the error screen in either diags or main bootmode.
This is the full log of booting in diags mode:
Code:
U-Boot 2009.08-lab126 (Mar 02 2021 - 17:14:13)
CPU: Freescale i.MX6 family TO0.0 at 996 MHz
Temperature: 30 C, calibration data 0x59c5205f
mx6sl pll1: 996MHz
mx6sl pll2: 528MHz
mx6sl pll3: 480MHz
mx6sl pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 66000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 198000000Hz
emi_slow clock: 22000000Hz
ddr clock : 396000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
MMC: FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2
Board: Pinot WFO
Boot Reason: [ POR ]
Boot Device: NAND
Board Id: 0272201145060JKR
S/N: 9017220145240BC8
I2C: ready
DRAM: 256 MB
Using default environment
In: serial
Out: serial
Err: serial
Quick Memory Test 0x80000000, 0xfff0000
POST done in 57 ms
BOOTMODE OVERRIDE: DIAGS
Battery voltage: 4030 mV
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at 80800000 ...
Image Name: Linux-3.0.35-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2420496 Bytes = 2.3 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000] Linux version 3.0.35-lab126 (jenkins-official@jbuild01) (collect2: ld returned 1 exit status) #1 Tue Sep 3 03:12:16 PDT 2013
[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Freescale i.MX 6SoloLite based Wario Board
[ 0.000000] Ignoring unrecognised tag 0x54410011
[ 0.000000] Will try to place printk log at 8fffc000
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU identified as i.MX6SoloLite, silicon rev 1.2
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat c04dcc94, node_mem_map c2000000
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 8128 pages, LIFO batch:0
[ 0.000000] Normal zone: 448 pages used for memmap
[ 0.000000] Normal zone: 56896 pages, LIFO batch:15
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: rootwait log_pos_goal=0x8fffc000 console=ttymxc0,115200 root=/dev/mmcblk0p2 ro ip=off debug video=mxcepdcfb:E60,bpp=8,x_mem=3M
[ 0.000000] Prink buffer will be relocated to physical address: 8fff2000
[ 0.000000] log_buf_len: 32768
[ 0.000000] early log buf free: 31293(95%)
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 254652k/254652k available, 7492k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xfde00000 - 0xffe00000 ( 32 MB)
[ 0.000000] vmalloc : 0xd0800000 - 0xf2000000 ( 536 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc010b000 (1036 kB)
[ 0.000000] .text : 0xc010b000 - 0xc04aa000 (3708 kB)
[ 0.000000] .data : 0xc04aa000 - 0xc04dd7c0 ( 206 kB)
[ 0.000000] .bss : 0xc04dd7e4 - 0xc0504540 ( 156 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:624
[ 0.000000] MXC GPIO hardware
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] arm_max_freq=1GHz
[ 0.000000] MXC_Early serial console at MMIO 0x2020000 (options '115200')
[ 0.000000] bootconsole [ttymxc0] enabled
[ 0.000000] Console: colour dummy device 80x30
[ 0.263046] Calibrating delay loop... 1987.37 BogoMIPS (lpj=9936896)
[ 0.321375] pid_max: default: 32768 minimum: 301
[ 0.326254] Mount-cache hash table entries: 512
[ 0.331165] CPU: Testing write buffer coherency: ok
[ 0.336192] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.351148] print_constraints: dummy:
[ 0.355099] NET: Registered protocol family 16
[ 0.363367] print_constraints: vddpu: 725 <--> 1300 mV at 700 mV fast normal
[ 0.370945] print_constraints: vddcore: 725 <--> 1300 mV at 1475 mV fast normal
[ 0.378644] print_constraints: vddsoc: 725 <--> 1300 mV at 1475 mV fast normal
[ 0.386310] print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
[ 0.394042] print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal
[ 0.401720] print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal
[ 0.410616] LAB126 Board id - 0272201145060JKR
[ 0.419152] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[ 0.425994] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
[ 0.433329] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.439201] L310 cache controller enabled
[ 0.443226] l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x02030000, Cache size: 262144 B
[ 0.459497] bio: create slab <bio-0> at 0
[ 0.467123] max77696> regulator init
[ 0.471603] spi_imx imx6q-ecspi.0: probed
[ 0.476188] usbcore: registered new interface driver usbfs
[ 0.481797] usbcore: registered new interface driver hub
[ 0.487303] usbcore: registered new device driver usb
[ 0.494441] Reboot Reason - Standard Reporting
[ 0.498917] kernel: I max77696-irq:evtrcrd: evt=MR_FRSTRT: Manual Reset Full Restart
[ 0.506680] Reboot Reason - Metric Framework Reporting
[ 0.511838] kernel: kernel_metric_generic,counter,event_recorder,ercflags,MR_FRSTRT,1,
[ 0.519774] Reboot Reason - Legacy Metric Reporting
[ 0.524666] boot: C def:bcut:batterycut=1
[ 0.530287] MAX77696 TOPSYS 1.0.0 Installed
[ 0.537152] max77696-gpio max77696-gpio.0: gpio#0 -- -- func-0 in
[ 0.544628] max77696-gpio max77696-gpio.0: gpio#1 -- -- func--1 in
[ 0.552403] max77696-gpio max77696-gpio.0: gpio#3 -- -- func-0 in
[ 0.560441] MAX77696 GPIO Driver 1.0.0 Installed
[ 0.566143] buck mode: 4
[ 0.569416] buck mode: 4
[ 0.572889] print_constraints: max77696_buck1: 900 <--> 1300 mV at 1250 mV fast normal idle standby
[ 0.582526] buck mode: 4
[ 0.586005] print_constraints: max77696_buck1dvs: 600 <--> 1300 mV at 900 mV fast normal idle standby
[ 0.595805] buck mode: 4
[ 0.599074] buck mode: 4
[ 0.602546] print_constraints: max77696_buck2: 900 <--> 1300 mV at 1200 mV fast normal idle standby
[ 0.612157] buck mode: 4
[ 0.615633] print_constraints: max77696_buck2dvs: 600 <--> 1300 mV at 900 mV fast normal idle standby
[ 0.625422] print_constraints: max77696_buck3: 600 <--> 3387 mV at 1300 mV fast normal idle standby
[ 0.635208] buck mode: 4
[ 0.638478] buck mode: 4
[ 0.641745] print_constraints: max77696_buck4: 1200 mV fast normal idle standby
[ 0.649597] buck mode: 4
[ 0.653074] print_constraints: max77696_buck5: 600 <--> 3387 mV at 1800 mV fast normal idle standby
[ 0.662689] buck mode: 4
[ 0.666166] print_constraints: max77696_buck6: 600 <--> 3387 mV at 3200 mV fast normal idle standby
[ 0.675276] MAX77696 Buck Regulators Driver 1.0.1 Installed
[ 0.681638] print_constraints: max77696_ldo1: 800 <--> 3950 mV at 3300 mV normal idle standby
[ 0.690769] print_constraints: max77696_ldo2: 800 <--> 3950 mV at 3000 mV normal idle standby
[ 0.699852] print_constraints: max77696_ldo3: 800 <--> 3950 mV at 2500 mV normal idle standby
[ 0.708963] print_constraints: max77696_ldo4: 800 <--> 2375 mV at 1800 mV normal idle standby
[ 0.718028] print_constraints: max77696_ldo5: 800 <--> 2375 mV at 1800 mV normal idle standby
[ 0.727147] print_constraints: max77696_ldo6: 800 <--> 3950 mV at 3200 mV normal idle standby
[ 0.736229] print_constraints: max77696_ldo7: 800 <--> 3950 mV at 3200 mV normal idle standby
[ 0.745336] print_constraints: max77696_ldo8: 800 <--> 2375 mV at 1100 mV normal idle standby
[ 0.754409] print_constraints: max77696_ldo9: 800 <--> 2375 mV at 1100 mV normal idle standby
[ 0.763541] print_constraints: max77696_ldo10: 2400 <--> 5550 mV at 5200 mV normal idle standby
[ 0.773069] MAX77696 Linear Regulators Driver 1.0.2 Installed
[ 0.779422] print_constraints: max77696_lsw1:
[ 0.784234] print_constraints: max77696_lsw2:
[ 0.788987] print_constraints: max77696_lsw3:
[ 0.793728] print_constraints: max77696_lsw4:
[ 0.798234] MAX77696 Load Switches Driver 1.0.0 Installed
[ 0.804860] print_constraints: max77696-display:
[ 0.810344] print_constraints: max77696-vcom:
[ 0.815123] print_constraints: max77696-vee:
[ 0.819843] print_constraints: max77696-vneg:
[ 0.824624] print_constraints: max77696-vpos:
[ 0.829381] print_constraints: max77696-vddh:
[ 0.834871]
[ 0.834874] EPD vreg probe complete!
[ 0.840526] print_constraints: max77696_vddq: 240 <--> 984 mV at 600 mV
[ 0.847306] MAX77696 LPDDR2 Termination Supply Driver 1.0.1 Installed
[ 0.855031] MAX77696 I2C Driver 1.0.0 Installed
[ 0.862102] i2c-core: driver [max17135] using legacy suspend method
[ 0.868390] i2c-core: driver [max17135] using legacy resume method
[ 0.874636] Switching to clocksource mxc_timer1
[ 0.889691] NET: Registered protocol family 2
[ 0.894149] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.901245] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.908417] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.914950] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.921328] TCP reno registered
[ 0.924480] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.930343] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.936962] NET: Registered protocol family 1
[ 0.941683] RPC: Registered named UNIX socket transport module.
[ 0.947621] RPC: Registered udp transport module.
[ 0.952359] RPC: Registered tcp transport module.
[ 0.957075] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.967760] etb: probe of etb failed with error -2
[ 0.972808] etm: probe of etm.0 failed with error -2
[ 0.978041] Static Power Management for Freescale i.MX6
[ 0.983303] wait mode is enabled for i.MX6
[ 0.987589] cpaddr = d0820000 suspend_iram_base=d081c000
[ 0.992977] PM driver module loaded
[ 0.996732] IMX usb wakeup probe
[ 1.000004] the wakeup pdata is 0xce1387c0
[ 1.004444] IMX usb wakeup probe
[ 1.007692] the wakeup pdata is 0xce1388c0
[ 1.012001] cpu regulator mode:ldo_bypass
[ 1.016224] _regulator_get: get() with no identifier
[ 1.021217] mx6_cpu_regulator_init: failed to get pu regulator
[ 1.027263] i.MXC CPU frequency driver
[ 1.044109] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.051153] msgmni has been set to 497
[ 1.055266] io scheduler noop registered
[ 1.059305] io scheduler cfq registered (default)
[ 1.064513] MAX77696 Backlight Driver 1.0.0 Installed
[ 1.070359] imx-sdma imx-sdma: loaded firmware 1.1
[ 1.079737] imx-sdma imx-sdma: initialized
[ 1.254128] Serial: IMX driver
[ 1.386282] console [ttymxc0] enabled, bootconsole disabled
[ 1.386282] console [ttymxc0] enabled, bootconsole disabled
[ 1.401790] loop: module loaded
[ 1.405001] MAX77696 32kHz Oscillator Driver 1.0.0 Installed
[ 1.411319] input: max77696-onkey as /devices/platform/imx-i2c.0/i2c-0/0-003c/max77696-onkey.0/input/input0
[ 1.424515] MAX77696 ONKEY Driver 1.0.0 Installed
[ 1.450584] max77696-rtc max77696-rtc.0: rtc core: registered max77696-rtc.0 as rtc0
[ 1.470543] max77696-rtc max77696-rtc.0: rtc core: registered max77696-rtc.1 as rtc1
[ 1.499851] MAX77696 RTC Driver 1.0.2 Installed
[ 1.505263] snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc2
[ 1.511998] i2c /dev entries driver
[ 1.519882] max77696-battery max77696-battery.0: Voltage alert 3400mV ... 4260mV
[ 1.528032] max77696-battery max77696-battery.0: SOC alert (disabled)
[ 1.536081] MAX77696 Fuel Gauge Driver 1.0.0 Installed
[ 1.542954] MAX77696 USB Interface Circuit Driver 1.0.0 Installed
[ 1.550768] max77696-adc max77696-adc.0: ADC average rate: 32 sample(s)
[ 1.557388] max77696-adc max77696-adc.0: ADC delay: 0 nsec
[ 1.562893] max77696-adc max77696-adc.0: ADC cur src: 50 uA
[ 1.568469] MAX77696 ADC Driver 1.0.1 Installed
[ 1.573683] imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
[ 1.582103] sdhci: Secure Digital Host Controller Interface driver
[ 1.588287] sdhci: Copyright(c) Pierre Ossman
[ 1.592770] mmc0: no vmmc regulator found
[ 1.598089] mmc0: SDHCI controller on platform [sdhci-esdhc-imx.1] using DMA
[ 1.606225] mmc1: no vmmc regulator found
[ 1.612627] mmc1: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA
[ 1.620389] Registered led device: max77696-leds.0
[ 1.625189] MAX77696 LED Driver #0 1.0.0 Installed
[ 1.634272] Registered led device: max77696-leds.1
[ 1.639070] MAX77696 LED Driver #1 1.0.0 Installed
[ 1.644402] nf_conntrack version 0.5.0 (3978 buckets, 15912 max)
[ 1.653123] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.658496] TCP cubic registered
[ 1.661752] NET: Registered protocol family 17
[ 1.666213] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 1.674019] LPDDR2 MfgId: 0x1 [Samsung]
[ 1.678159] Bus freq driver module loaded
[ 1.684207] Bus freq driver Enabled
[ 1.688683] mxc_dvfs_core_probe
[ 1.695130] max77696-adc max77696-adc.0: adc conversion timed out
[ 1.702388] DVFS driver module loaded
[ 1.725288] regulator_init_complete: max77696_ldo10: incomplete constraints, leaving on
[ 1.740557] regulator_init_complete: max77696_ldo7: incomplete constraints, leaving on
[ 1.750735] regulator_init_complete: max77696_ldo6: incomplete constraints, leaving on
[ 1.769954] max77696-adc max77696-adc.0: adc conversion timed out
[ 1.777476]
[ 1.777479] ADC value out of thermistor range! setting display temp to 43 deg C
[ 1.787331] regulator_init_complete: max77696_buck6: incomplete constraints, leaving on
[ 1.795583] regulator_init_complete: max77696_buck5: incomplete constraints, leaving on
[ 1.804060] regulator_init_complete: max77696_buck2dvs: incomplete constraints, leaving on
[ 1.812410] emmc: I def:mmcpartinfo:vendor=toshiba, host=mmc0:
[ 1.818424] regulator_init_complete: max77696_buck1dvs: incomplete constraints, leaving on
[ 1.841156] mmc0: unrecognised EXT_CSD revision 7
[ 1.845868] mmc0: error -22 whilst initialising MMC card
[ 1.853645] max77696-rtc max77696-rtc.0: setting system clock to 2000-01-01 02:01:02 UTC (946692062)
[ 1.892315] MAX77696 Main Charger Driver 1.0.0 Installed
[ 1.951220] MAX77696 Energy Harvester Driver 1.0.0 Installed
[ 1.971337] Freeing init memory: 1036K
3.0.35-lab126 #1 Tue Sep 3 03:12:16 PDT 2013 armv7l
[ 2.050390] emmc: I def:mmcpartinfo:vendor=toshiba, host=mmc0:
[ 2.079325] mmc0: unrecognised EXT_CSD revision 7
[ 2.084056] mmc0: error -22 whilst initialising MMC card
[ 2.280911] emmc: I def:mmcpartinfo:vendor=toshiba, host=mmc0:
[ 2.317397] mmc0: unrecognised EXT_CSD revision 7
[ 2.322144] mmc0: error -22 whilst initialising MMC card
[ 2.391958] add wake up source irq 104
[ 2.552535] emmc: I def:mmcpartinfo:vendor=toshiba, host=mmc0:
[ 2.611811] mmc0: unrecognised EXT_CSD revision 7
[ 2.616539] mmc0: error -22 whilst initialising MMC card
[ 3.529882] KERNEL: I pmic:fg battery id check::wario_battery_valid=1
And this is the full log of booting in main mode:
Code:
U-Boot 2009.08-lab126 (Mar 02 2021 - 17:14:13)
CPU: Freescale i.MX6 family TO0.0 at 996 MHz
Temperature: 36 C, calibration data 0x59c5205f
mx6sl pll1: 996MHz
mx6sl pll2: 528MHz
mx6sl pll3: 480MHz
mx6sl pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 66000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 198000000Hz
emi_slow clock: 22000000Hz
ddr clock : 396000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
MMC: FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2
Board: Pinot WFO
Boot Reason: [ POR ]
Boot Device: NAND
Board Id: 0272201145060JKR
S/N: 9017220145240BC8
I2C: ready
DRAM: 256 MB
Using default environment
In: serial
Out: serial
Err: serial
Quick Memory Test 0x80000000, 0xfff0000
POST done in 57 ms
Battery voltage: 4021 mV
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at 80800000 ...
Image Name: Linux-3.0.35-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2420416 Bytes = 2.3 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.094347] boot: C def:bcut:batterycut=1
[ 0.098367]
[ 0.258830] LPDDR2 MfgId: 0x1 [Samsung]
[ 0.279801] max77696-adc max77696-adc.0: adc conversion timed out
3.0.35-lab126 #1 Wed Aug 28 15:30:45 PDT 2013 armv7l
[ 0.374999] mmc0: unrecognised EXT_CSD revision 7
[ 0.379724] mmc0: error -22 whilst initialising MMC card
[ 0.593841] mmc0: unrecognised EXT_CSD revision 7
[ 0.598568] mmc0: error -22 whilst initialising MMC card
[ 0.821901] mmc0: unrecognised EXT_CSD revision 7
[ 0.826628] mmc0: error -22 whilst initialising MMC card
[ 1.086362] mmc0: unrecognised EXT_CSD revision 7
[ 1.091108] mmc0: error -22 whilst initialising MMC card
I saw someone get a similar message in this thread's post #5
https://www.mobileread.com/forums/sh...d.php?t=348137
Might this be a dead eMMC or is the diags_kernel.img incompatible with my eMMC. Or what else could this be?
After letting it sit, in the serial logs I also keep recieving this message, like in post #1 of this thread:
https://www.mobileread.com/forums/sh...d.php?t=290861
Code:
[ 62.017489] max77696-adc max77696-adc.0: adc conversion timed out
[ 62.047565] max77696-adc max77696-adc.0: adc conversion timed out
[ 62.054040]
[ 62.054048] ADC value out of thermistor range! setting display temp to 43 deg C
If more information is needed, I will try to provide it.