I am wondering if it's even caused by the jailbreak. Is the flash memory just dead?
Here is a log if someone can help me out:
[ 58.887965] imx2-wdt imx2-wdt.0: Device shutdown: Expect reboot!
[ 58.895259] Restarting system.
HW
U-Boot 2009.08-lab126 (Dec 03 2021 - 04:34:48)
CPU: Freescale i.MX6 family TO0.0 at 996 MHz
Temperature: 29 C, calibration data 0x58950f5f
mx6sl pll1: 996MHz
mx6sl pll2: 528MHz
mx6sl pll3: 480MHz
mx6sl pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 66000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 198000000Hz
emi_slow clock: 22000000Hz
ddr clock : 396000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
MMC: FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2
Board: Pinot WFO
Boot Reason: [ POR ]
Boot Device: NAND
Board Id: 0272201144330SEP
S/N: 9017220144640DN2
I2C: ready
DRAM: 256 MB
Using default environment
In: serial
Out: serial
Err: serial
Quick Memory Test 0x80000000, 0xfff0000
POST done in 57 ms
BOOTMODE OVERRIDE: DIAGS
Battery voltage: 3980 mV
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at 80800000 ...
Image Name: Linux-3.0.35-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2420504 Bytes = 2.3 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000] Linux version 3.0.35-lab126 (jenkins-official@sjc10-jbuild10) (co llect2: ld returned 1 exit status) #1 Wed Apr 23 16:52:30 PDT 2014
[ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Freescale i.MX 6SoloLite based Wario Board
[ 0.000000] Ignoring unrecognised tag 0x54410011
[ 0.000000] Will try to place printk log at 8fffc000
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU identified as i.MX6SoloLite, silicon rev 1.2
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat c04dcc94, node_mem_map c200000 0
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 8128 pages, LIFO batch:0
[ 0.000000] Normal zone: 448 pages used for memmap
[ 0.000000] Normal zone: 56896 pages, LIFO batch:15
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 65024
[ 0.000000] Kernel command line: rootwait log_pos_goal=0x8fffc000 console=tty mxc0,115200 root=/dev/mmcblk0p2 ro ip=off debug video=mxcepdcfb:E60,bpp=8,x_mem= 3M
[ 0.000000] Prink buffer will be relocated to physical address: 8fff2000
[ 0.000000] log_buf_len: 32768
[ 0.000000] early log buf free: 31286(95%)
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 254652k/254652k available, 7492k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xfde00000 - 0xffe00000 ( 32 MB)
[ 0.000000] vmalloc : 0xd0800000 - 0xf2000000 ( 536 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .init : 0xc0008000 - 0xc010b000 (1036 kB)
[ 0.000000] .text : 0xc010b000 - 0xc04aa000 (3708 kB)
[ 0.000000] .data : 0xc04aa000 - 0xc04dd7c0 ( 206 kB)
[ 0.000000] .bss : 0xc04dd7e4 - 0xc0504540 ( 156 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, N odes=1
[ 0.000000] NR_IRQS:624
[ 0.000000] MXC GPIO hardware
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 17895 6ms
[ 0.000000] arm_max_freq=1GHz
[ 0.000000] MXC_Early serial console at MMIO 0x2020000 (options '115200')
[ 0.000000] bootconsole [ttymxc0] enabled
[ 0.000000] Console: colour dummy device 80x30
[ 0.263655] Calibrating delay loop... 1987.37 BogoMIPS (lpj=9936896)
[ 0.321982] pid_max: default: 32768 minimum: 301
[ 0.326861] Mount-cache hash table entries: 512
[ 0.331766] CPU: Testing write buffer coherency: ok
[ 0.336793] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counter s available
[ 0.351760] print_constraints: dummy:
[ 0.355711] NET: Registered protocol family 16
[ 0.363966] print_constraints: vddpu: 725 <--> 1300 mV at 700 mV fast normal
[ 0.371548] print_constraints: vddcore: 725 <--> 1300 mV at 1475 mV fast norm al
[ 0.379245] print_constraints: vddsoc: 725 <--> 1300 mV at 1475 mV fast norma l
[ 0.386914] print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast norm al
[ 0.394641] print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast norma l
[ 0.402313] print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast norm al
[ 0.411212] LAB126 Board id - 0272201144330SEP
[ 0.419746] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[ 0.426588] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-ste p.
[ 0.433922] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.439793] L310 cache controller enabled
[ 0.443818] l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x02030000, Cache si ze: 262144 B
[ 0.460052] bio: create slab <bio-0> at 0
[ 0.467671] max77696> regulator init
[ 0.472146] spi_imx imx6q-ecspi.0: probed
[ 0.476734] usbcore: registered new interface driver usbfs
[ 0.482343] usbcore: registered new interface driver hub
[ 0.487848] usbcore: registered new device driver usb
[ 0.494975] Reboot Reason - Standard Reporting
[ 0.499450] kernel: I max77696-irq:evtrcrd: evt=SFT_PRSTRT: Software Partial Restart
[ 0.507213] Reboot Reason - Metric Framework Reporting
[ 0.512372] kernel: kernel_metric_generic,counter,event_recorder,ercfl ags,SFT _PRSTRT,1,
[ 0.520395] Reboot Reason - Legacy Metric Reporting
[ 0.525287]
[ 0.528375] MAX77696 TOPSYS 1.0.0 Installed
[ 0.535203] max77696-gpio max77696-gpio.0: gpio#0 -- -- func-0 in
[ 0.542719] max77696-gpio max77696-gpio.0: gpio#1 -- -- func--1 in
[ 0.550459] max77696-gpio max77696-gpio.0: gpio#3 -- -- func-0 in
[ 0.558509] MAX77696 GPIO Driver 1.0.0 Installed
[ 0.564203] buck mode: 4
[ 0.567513] buck mode: 4
[ 0.570987] print_constraints: max77696_buck1: 900 <--> 1300 mV at 1250 mV fa st normal idle standby
[ 0.580596] buck mode: 4
[ 0.584072] print_constraints: max77696_buck1dvs: 600 <--> 1300 mV at 900 mV fast normal idle standby
[ 0.593872] buck mode: 4
[ 0.597140] buck mode: 4
[ 0.600612] print_constraints: max77696_buck2: 900 <--> 1300 mV at 1200 mV fa st normal idle standby
[ 0.610214] buck mode: 4
[ 0.613690] print_constraints: max77696_buck2dvs: 600 <--> 1300 mV at 900 mV fast normal idle standby
[ 0.623475] print_constraints: max77696_buck3: 600 <--> 3387 mV at 1300 mV fa st normal idle standby
[ 0.633266] buck mode: 4
[ 0.636534] buck mode: 4
[ 0.639802] print_constraints: max77696_buck4: 1200 mV fast normal idle stand by
[ 0.647656] buck mode: 4
[ 0.651131] print_constraints: max77696_buck5: 600 <--> 3387 mV at 1800 mV fa st normal idle standby
[ 0.660744] buck mode: 4
[ 0.664218] print_constraints: max77696_buck6: 600 <--> 3387 mV at 3200 mV fa st normal idle standby
[ 0.673326] MAX77696 Buck Regulators Driver 1.0.1 Installed
[ 0.679688] print_constraints: max77696_ldo1: 800 <--> 3950 mV at 3300 mV nor mal idle standby
[ 0.688816] print_constraints: max77696_ldo2: 800 <--> 3950 mV at 3000 mV nor mal idle standby
[ 0.697900] print_constraints: max77696_ldo3: 800 <--> 3950 mV at 2500 mV nor mal idle standby
[ 0.707017] print_constraints: max77696_ldo4: 800 <--> 2375 mV at 1800 mV nor mal idle standby
[ 0.716081] print_constraints: max77696_ldo5: 800 <--> 2375 mV at 1800 mV nor mal idle standby
[ 0.725195] print_constraints: max77696_ldo6: 800 <--> 3950 mV at 3200 mV nor mal idle standby
[ 0.734280] print_constraints: max77696_ldo7: 800 <--> 3950 mV at 3200 mV nor mal idle standby
[ 0.743390] print_constraints: max77696_ldo8: 800 <--> 2375 mV at 1100 mV nor mal idle standby
[ 0.752459] print_constraints: max77696_ldo9: 800 <--> 2375 mV at 1100 mV nor mal idle standby
[ 0.761583] print_constraints: max77696_ldo10: 2400 <--> 5550 mV at 5200 mV n ormal idle standby
[ 0.771088] MAX77696 Linear Regulators Driver 1.0.2 Installed
[ 0.777435] print_constraints: max77696_lsw1:
[ 0.782250] print_constraints: max77696_lsw2:
[ 0.787007] print_constraints: max77696_lsw3:
[ 0.791744] print_constraints: max77696_lsw4:
[ 0.796251] MAX77696 Load Switches Driver 1.0.0 Installed
[ 0.802877] print_constraints: max77696-display:
[ 0.808358] print_constraints: max77696-vcom:
[ 0.813133] print_constraints: max77696-vee:
[ 0.817853] print_constraints: max77696-vneg:
[ 0.822632] print_constraints: max77696-vpos:
[ 0.827392] print_constraints: max77696-vddh:
[ 0.832877]
[ 0.832881] EPD vreg probe complete!
[ 0.838520] print_constraints: max77696_vddq: 240 <--> 984 mV at 600 mV
[ 0.845301] MAX77696 LPDDR2 Termination Supply Driver 1.0.1 Installed
[ 0.853034] MAX77696 I2C Driver 1.0.0 Installed
[ 0.860116] i2c-core: driver [max17135] using legacy suspend method
[ 0.866404] i2c-core: driver [max17135] using legacy resume method
[ 0.872650] Switching to clocksource mxc_timer1
[ 0.887729] NET: Registered protocol family 2
[ 0.892186] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.899278] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.906450] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.912984] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.919362] TCP reno registered
[ 0.922515] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.928379] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.934999] NET: Registered protocol family 1
[ 0.939730] RPC: Registered named UNIX socket transport module.
[ 0.945668] RPC: Registered udp transport module.
[ 0.950405] RPC: Registered tcp transport module.
[ 0.955122] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.965805] etb: probe of etb failed with error -2
[ 0.970854] etm: probe of etm.0 failed with error -2
[ 0.976087] Static Power Management for Freescale i.MX6
[ 0.981350] wait mode is enabled for i.MX6
[ 0.985632] cpaddr = d0820000 suspend_iram_base=d081c000
[ 0.991025] PM driver module loaded
[ 0.994779] IMX usb wakeup probe
[ 0.998051] the wakeup pdata is 0xce1387c0
[ 1.002490] IMX usb wakeup probe
[ 1.005738] the wakeup pdata is 0xce1388c0
[ 1.010046] cpu regulator mode:ldo_bypass
[ 1.014268] _regulator_get: get() with no identifier
[ 1.019262] mx6_cpu_regulator_init: failed to get pu regulator
[ 1.025309] i.MXC CPU frequency driver
[ 1.042211] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.049248] msgmni has been set to 497
[ 1.053359] io scheduler noop registered
[ 1.057396] io scheduler cfq registered (default)
[ 1.062605] MAX77696 Backlight Driver 1.0.0 Installed
[ 1.068459] imx-sdma imx-sdma: loaded firmware 1.1
[ 1.077840] imx-sdma imx-sdma: initialized
[ 1.253007] Serial: IMX driver
[ 1.385156] console [ttymxc0] enabled, bootconsole disabled
[ 1.385156] console [ttymxc0] enabled, bootconsole disabled
[ 1.400675] loop: module loaded
[ 1.403883] MAX77696 32kHz Oscillator Driver 1.0.0 Installed
[ 1.410236] input: max77696-onkey as /devices/platform/imx-i2c.0/i2c-0/0-003c /max77696-onkey.0/input/input0
[ 1.423430] MAX77696 ONKEY Driver 1.0.0 Installed
[ 1.448596] max77696-rtc max77696-rtc.0: rtc core: registered max77696-rtc.0 as rtc0
[ 1.468559] max77696-rtc max77696-rtc.0: rtc core: registered max77696-rtc.1 as rtc1
[ 1.497863] MAX77696 RTC Driver 1.0.2 Installed
[ 1.503275] snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc2
[ 1.510008] i2c /dev entries driver
[ 1.517865] max77696-battery max77696-battery.0: Voltage alert 3400mV ... 4260mV
[ 1.526017] max77696-battery max77696-battery.0: SOC alert (disabled)
[ 1.534067] MAX77696 Fuel Gauge Driver 1.0.0 Installed
[ 1.540956] MAX77696 USB Interface Circuit Driver 1.0.0 Installed
[ 1.549401] max77696-adc max77696-adc.0: ADC average rate: 32 sample(s)
[ 1.556020] max77696-adc max77696-adc.0: ADC delay: 0 nsec
[ 1.561523] max77696-adc max77696-adc.0: ADC cur src: 50 uA
[ 1.567100] MAX77696 ADC Driver 1.0.1 Installed
[ 1.572309] imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (n owayout=1)
[ 1.580727] sdhci: Secure Digital Host Controller Interface driver
[ 1.586912] sdhci: Copyright(c) Pierre Ossman
[ 1.591397] mmc0: no vmmc regulator found
[ 1.596712] mmc0: SDHCI controller on platform [sdhci-esdhc-imx.1] using DMA
[ 1.604847] mmc1: no vmmc regulator found
[ 1.611245] mmc1: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA
[ 1.619005] Registered led device: max77696-leds.0
[ 1.623807] MAX77696 LED Driver #0 1.0.0 Installed
[ 1.632892] Registered led device: max77696-leds.1
[ 1.637705] MAX77696 LED Driver #1 1.0.0 Installed
[ 1.643027] nf_conntrack version 0.5.0 (3978 buckets, 15912 max)
[ 1.651737] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.657108] TCP cubic registered
[ 1.660365] NET: Registered protocol family 17
[ 1.664823] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 1.672628] LPDDR2 MfgId: 0x3 [Elpida]
[ 1.676692] Bus freq driver module loaded
[ 1.682742] Bus freq driver Enabled
[ 1.687257] mxc_dvfs_core_probe
[ 1.694819] DVFS driver module loaded
[ 1.717913] regulator_init_complete: max77696_ldo10: incomplete constraints, leaving on
[ 1.733160] regulator_init_complete: max77696_ldo7: incomplete constraints, l eaving on
[ 1.750517] regulator_init_complete: max77696_ldo6: incomplete constraints, l eaving on
[ 1.765724] regulator_init_complete: max77696_buck6: incomplete constraints, leaving on
[ 1.773951] regulator_init_complete: max77696_buck5: incomplete constraints, leaving on
[ 1.782667] regulator_init_complete: max77696_buck2dvs: incomplete constraint s, leaving on
[ 1.791020] emmc: I def:mmcpartinfo:vendor=toshiba, host=mmc0:
[ 1.800255] regulator_init_complete: max77696_buck1dvs: incomplete constraint s, leaving on
[ 1.839384] mmc0: new high speed DDR MMC card at address 0001
[ 1.845532] mmcblk0: mmc0:0001 004GE0 3.68 GiB
[ 1.850221] mmcblk0boot0: mmc0:0001 004GE0 partition 1 2.00 MiB
[ 1.856269] mmcblk0boot1: mmc0:0001 004GE0 partition 2 2.00 MiB
[ 1.862853] max77696-rtc max77696-rtc.0: setting system clock to 2000-01-01 0 1:13:10 UTC (946689190)
[ 1.872262] mmcblk0: p1 p2 p3 p4
[ 1.878610] mmcblk0boot1: unknown partition table
[ 1.885656] mmcblk0boot0: unknown partition table
[ 1.896755] KERNEL: I pmic:charger chgina::charger connected
[ 1.912390] MAX77696 Main Charger Driver 1.0.0 Installed
[ 1.921094] MAX77696 Energy Harvester Driver 1.0.0 Installed
[ 1.927710] Freeing init memory: 1036K
3.0.35-lab126 #1 Wed Apr 23 16:52:30 PDT 2014 armv7l
[ 1.957746] INFO:Loaded module /lib/modules/mxc_epdc_eink.ko (10304 bytes)
[ 2.397230] add wake up source irq 104
[ 3.527245] KERNEL: I pmic:fg battery id check::wario_battery_valid=1
[ 5.176887] INFO:Loaded module /lib/modules/mxc_epdc_fb.ko (83340 bytes)
[ 5.469635] INFO:eink initialized... (786432 bytes)
[ 5.474579] INFO
IAGS MODE
Press [ENTER] for recovery menu... 0 /[ 6.483987] INFO:!!! Checking MBR /dev/mmcblk0 !!!!
[ 6.494124] INFO
artition 2, start sector is 782336
[ 6.499238] INFO
artition 3, start sector is 913408
[ 6.504286] INFO
artition 4, start sector is 1044480
[ 6.509425] INFO:maximizing partition 6688768 sectors
[ 6.514520] INFO:*** Partition table verified for /dev/mmcblk0 ***
/dev/mmcblk0p4:[ 6.522835] INFO:Setup loop device /dev/loop0 for /dev/mmcblk0 p4 + 8192
CHS=4/16/104512 size=3424649216 bytes
flag type first [ 6.533196] INFO:Checking for updates... (auto-pilot mode)
last lba first lba size
Pa[ 6.541812] INFO:No update*.bin found; no update needed.
rtition p1:
0x00 0x0b 16 <large> 16 6688752
CHS: 0/1/1 - <large>
Par[ 6.557552] INFO:no updates found.
tition p2:
Partition p3:
Partition p4:
BOOTING DEFAULT.
IP-Config: no devices to configure
[ 7.523407] EXT3-fs: barriers not enabled
[ 7.528157] kjournald starting. Commit interval 5 seconds
[ 7.533704] EXT3-fs (mmcblk0p2): mounted filesystem with writeback data mode
kinit: Mounted root (ext3 filesystem) readonly.
kinit: init not found!