After launching Kubrick for a second time from a different DVD, it looks exactly as it was before. Is the the new WiFi chip recognized or for some reason reader doesn't like the new MAC address...?
Code:
U-Boot 1.3.0-rc3-lab126 (Apr 16 2011 - 20:15:23)
CPU: Freescale i.MX35 at 532 MHz
Board: MX35 Luigi [ POR]
WDOG_WCR = 0xff31
WDOG_WMCR = 0x0
Board Id: SP1B000000000000
S/N: B00AA0A004850761
DRAM: 256 MB
Using default environment
In: serial
Out: serial
Err: serial
No ethernet found.
i.MX35 CPU board version 2.0
Net: No ethernet found.
Hit any key to stop autoboot: 0
## Booting image at 87f40400 ...
Image Name: Linux-2.6.26-rt-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2167548 Bytes = 2.1 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
Uncompressing Linux.......................................................................................................................... done, booting the kernel.
boot: C def:bcut:batterycut=1,version=s172597:
2.6.26-rt-lab126 #5 Sat Sep 1 14:28:26 PDT 2012 armv6l
INFO:Using default keypad setting. (not passing "kb_rev" to module)
INFO:Loaded module /lib/modules/mxc_keyb.ko (22508 bytes)
Press [ENTER] for recovery menu... 0 /INFO:Partition table verified for /dev/mmcblk0
INFO:Checking for updates... (auto-pilot mode)
/dev/mmcblk0p4:
CHS=4/16/98887 size=3240329216 bytes
flag type first last lba first lba size
Partition p1:
0x00 0x0b 16 <large> 16 6328752
CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
INFO:Setup loop device /dev/loop0 for /dev/mmcblk0p4 + 8192
INFO:No update*.bin found; no update needed.
INFO:no updates found.
BOOTING DEFAULT.
argc == 9
argv[0]: "kinit"
argv[1]: "console=ttymxc0,115200"
argv[2]: "mem=256M"
argv[3]: "panic=10"
argv[4]: "root=/dev/mmcblk0p1"
argv[5]: "ro"
argv[6]: "ip=none"
argv[7]: "quiet"
argv[8]: "lpj=2555904"
Running ipconfig
argc == 4
argv[0]: "IP-Config"
argv[1]: "-i"
argv[2]: "Linux kinit"
argv[3]: "ip=none"
IP-Config: no devices to configure
kinit: do_mounts
kinit: name_to_dev_t(/dev/mmcblk0p1) = dev(179,1)
kinit: root_dev = dev(179,1)
kinit: /dev/root appears to be a ext3 filesystem
kinit: trying to mount /dev/root on /root with type ext3
kinit: Mounted root (ext3 filesystem) readonly.
Checking for init: /sbin/init
Checking for init: /bin/init
Checking for init: /etc/init
Checking for init: /sbin/init.sysvinit
INIT: version 2.86 booting
system: I rcS:def:starting /etc/rcS.d/S02kdb
system: I S02kdb:def:Setting boot device to mmcblk0
kdb set: 'system/driver/filesystem/DEV_ROOT'
system: I rcS:def:starting /etc/rcS.d/S03udev
system: I S03udev:def:setting up virtual fs for hotplug event handling
system: I S03udev:def:starting the hotplug events dispatcher
system: I S03udev:def:synthesizing initial hotplug events
lipc-send-event[378]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[378]: C def:dbusi::Failed to init dbus
lipc-send-event[378]: E def:open::Failed to open LIPC
lipc-send-event[378]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
lipc-send-event[475]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[475]: C def:dbusi::Failed to init dbus
lipc-send-event[475]: E def:open::Failed to open LIPC
lipc-send-event[475]: E def:fail:source=com.lab126.hal, event=audioHS:Sending event failed
system: I rcS:def:starting /etc/rcS.d/S04rootfsresize
system: I S04rootfsresize:def:No rootfs on /dev/mmcblk0p1 resizing needed
system: I rcS:def:starting /etc/rcS.d/S10filesystems
system: I rcS:def:starting /etc/rcS.d/S10hostname
system: I rcS:def:starting /etc/rcS.d/S10network
system: I S10hostname:def:setting device hostname
system: I S10filesystems:def:mounting filesystems
system: I S10network:def:initializing network configuration
system: I S10network:def:Installed Firewall
system: I rcS:def:starting /etc/rcS.d/S11chpriority
system: I rcS:def:starting /etc/rcS.d/S11video
Unknown HZ value! (94) Assume 100.
system: W S11chpriority:def:Cannot set priority for IRQ-7
system: I S11video:def:initializing eInk HAL for system use
system: I S11video:def:eink_debug=0
system: I S11video:def:Controller set to broads
system: I rcS:def:starting /etc/rcS.d/S20syslog-ng
system: I S20syslog-ng:def:starting syslog-ng
system: I rcS:def:starting /etc/rcS.d/S21init_time
system: I S21init_time:initboot:time=13600:boot time after init in milliseconds
system: I rcS:def:starting /etc/rcS.d/S45modules
system: I S45modules:def:loading module mwan
system: I S45modules:def:loading module g_file_storage
system: I S45modules:def:loading module fuse
system: I S45modules:def:loading module uinput
system: I S45modules:def:loading module mxc_keyb
system: I S45modules:def:loading module fiveway
system: I S45modules:def:loading module volume
system: I rcS:def:starting /etc/rcS.d/S50system
mount: mount point /proc/bus/usb does not exist
Fri Jun 1 00:00:00 UTC 2012
system: I rcS:def:starting /etc/rcS.d/S55scroll
system: I S55scroll:def:skipping; no luigi-based work to do here
system: I rcS:def:starting /etc/rcS.d/S70ethernet
system: I rcS:def:starting /etc/rcS.d/S70userstore
system: I S70ethernet:def:not enet
system: I S70ethernet:def:not usbnet
dosfsck 2.11-lab126 (1 Jun 2007)
dosfsck 2.11-lab126, 1 Jun 2007, FAT32, LFN
Checking we can access the last sector of the filesystem
Boot sector contents:
System ID "mkdosfs"
Media byte 0xf8 (hard disk)
512 bytes per logical sector
8192 bytes per cluster
32 reserved sectors
First FAT starts at byte 16384 (sector 32)
2 FATs, 32 bit entries
1581056 bytes per FAT (= 3088 sectors)
Root directory start at cluster 2 (arbitrary size)
Data area starts at byte 3178496 (sector 6208)
395159 data clusters (3237142528 bytes)
32 sectors/track, 64 heads
0 hidden sectors
6328752 sectors total
Checking for unused clusters.
Checking free cluster summary.
/dev/loop/0: 6 files, 159/395159 clusters
system: I rcS:def:starting /etc/rcS.d/S90video
system: I S90video:def:initializing eInk HAL for rootfs use
INIT: Entering runlevel: 2
system: I lifeguard:def:starting eInk HAL lifeguard
system: I S40diags:def:not starting Diagnostic Services
system: I S40diags:def:/mnt/base-us/ENABLE_DIAGS does not exist, forcing diagnostic disable
system: I S50battcheck:def:running
Fri Jun 1 00:00:03 2012 INFO:battery voltage: 4022 mV
Fri Jun 1 00:00:03 2012 INFO:battery charge: 88%
system: I S50battcheck:def:current voltage = 4037mV
Fri Jun 1 00:00:04 2012 INFO:battery charge: 88%
Fri Jun 1 00:00:04 2012 INFO:battery voltage: 4022 mV
Fri Jun 1 00:00:04 2012 INFO:battery current: -149 mA
system: I S50battcheck:def:gasgauge capacity=88% volts=4022 mV current=-149 mA
system: I S50battcheck:def:Waiting for 3460mV or 4%
system: I S50battcheck:def:battery sufficient, booting to normal runlevel
INIT: Switching to runlevel: 5
INIT: Sending processes the TERM signal
Platform set to SHASTA_NATIVEMMC-SDIO
Platform Setup Script is: /opt/ar6k/host/support/platformscripts/plat_SHASTA_NATIVEMMC-SDIO.sh
Image path: /sbin
No debug record limit set
export AR6002_REV='2'
export AR6K_MODULE_ARGS='bmienable=1 ifname=wlan0 fwmode=1 busspeedlow=0'
export AR6K_MODULE_NAME='ar6000'
export AR6K_TGT_LOGFILE='/tmp/dbglog.out'
export ATH_PLATFORM='SHASTA_NATIVEMMC-SDIO'
export ATH_SDIO_STACK_PARAMS='RequestListSize=128 '
export CONSOLE='/dev/console'
export EEPROM='/opt/ar6k/target/AR6002/hw2.0/bin/lab126_15dBm_nodiv_WWR_CTL.bin'
export HOME='/'
export IMAGEPATH='/sbin'
export INIT_VERSION='sysvinit-2.86'
export PATH='/bin:/usr/bin:/sbin:/usr/sbin'
export PREVLEVEL='2'
export PWD='/'
export RUNLEVEL='5'
export TARGET='AR6002'
export TARGET_TYPE='AR6002'
export TERM='linux'
export VERBOSE='no'
export WORKAREA='/opt/ar6k'
export previous='2'
export runlevel='5'
Load Board Data from /opt/ar6k/target/AR6002/hw2.0/bin/lab126_15dBm_nodiv_WWR_CTL.bin
Updating MAC address
/sbin/eeprom.AR6002 is waiting for Target....