2Had an epiphany while reading another thread....I did not have the power cable connected to wall power while doing the DO_FACTORY_RESET it was connected to the PC, so I decided to have another go and this time I could watch from the serial port and see what was going on.
I put back the DO_FACTORY_RESET file into the root of the kindle over USB, then connected the cable to wall charger, reboot and voila! It performed a factory reset and the kindle came up as if I never used it before, re-registered and it's back online.
Suck it Amazon you bastards for telling me it would never work and trying to make me buy a new one! Worst service ever from a usually great company.
In case it's useful for someone else, here's the most recent bits of the serial log, I think it does the reset in here.
Code:
U-Boot 2009.08-lab126 (Aug 05 2014 - 04:37:39)
CPU: Freescale i.MX6 family TO0.0 at 996 MHz
Temperature: 37 C, calibration data 0x5df5515f
mx6sl pll1: 996MHz
mx6sl pll2: 528MHz
mx6sl pll3: 480MHz
mx6sl pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 66000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 198000000Hz
emi_slow clock: 22000000Hz
ddr clock : 396000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
MMC: FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2
Board: Pinot WFO
Boot Reason: [ POR ]
Boot Device: NAND
Board Id: 0272201144120JFX
S/N: 901722
I2C: ready
DRAM: 256 MB
Using default environment
In: serial
Out: serial
Err: serial
Quick Memory Test 0x80000000, 0xfff0000
POST done in 60 ms
Battery voltage: 4001 mV
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at 80800000 ...
Image Name: Linux-3.0.35-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2593852 Bytes = 2.5 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.098514]
[ 0.272546] LPDDR2 MfgId: 0x1 [Samsung]
[ 0.276624]
[ 0.276627] just text: vaddr c013f678, va 0xc013f200 pa 0x801000c3 attr 0x6
[ 0.289178]
[ 0.289181] nmx6sl_wfi_iram: vaddr d084e000, va 0xd084e200 pa 0x904043 attr 0x2
[ 0.298026]
[ 0.298028] mx6sl_ddr: vaddr d0856000, va 0xd0856200 pa 0x905043 attr 0x2
[ 0.306354]
[ 0.306357] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149
[ 0.317193]
[ 0.317196] ANATOP: vaddr f40c8000, va 0xf40c8200 pa 0x20110c3 attr 0x149
[ 0.331545]
[ 0.331548] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149
[ 0.343690]
[ 0.343692] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149
[ 0.354098]
[ 0.354101] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149
[ 0.363998]
[ 0.364000] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149
3.0.35-lab126 #1 PREEMPT Wed Dec 10 13:49:16 PST 2014 armv7l
Press [ENTER] for recovery menu... 0 //dev/mmcblk0p4:
CHS=4/16/104512 size=3424649216 bytes
flag type first last lba first lba size
Partition p1:
0x00 0x0b 16 <large> 16 6688752
CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
BOOTING DEFAULT.
IP-Config: no devices to configure
kinit: Mounted root (ext3 filesystem) readonly.
info sytem:mounted_proc::
info system:mounted_sys::
info system:mounted_dev::
info milestone:6.72:49.1:
info milestone:6.76:49.2:
info milestone:6.79:49.3:
info milestone:6.83:49.4:
info milestone:6.86:49.5:
info sytem:mounted_tmpfs::
info milestone:6.93:sy50:
info system:start:time=6960:
info hardware:no_wan::WiFi only device. No WAN found
info system:config:platform=wario,board=pinot,rev=34,proto=Y,wifi=Y,wan=N:
info milestone:7.11:sy51:
lipc-send-event[806]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[806]: C def:dbusi::Failed to init dbus
lipc-send-event[806]: E def:open::Failed to open LIPC
lipc-send-event[806]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
lipc-send-event[805]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[805]: C def:dbusi::Failed to init dbus
lipc-send-event[805]: E def:open::Failed to open LIPC
lipc-send-event[805]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
info milestone:8.01:sy99:
info system:done:time=8039:
init.exe: sshd main process (817) terminated with status 2
init.exe: sshd main process ended, respawning
crond[819]: crond: crond (busybox 1.17.1) started, log level 8
init.exe: recevent pre-start process (822) terminated with status 1
info system_cramfs_loopbacks:mountingcramfs:Mounting compressed directories filesystem images:
warn system_cramfs_loopbacks:mountpointmissing:Image /lib/firmware/cyttsp.cramfs.img not mounted, non existing mounting point:
info system_cramfs_loopbacks:mounted:Image /usr/share/X11/xkb.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/java/lib/fonts.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /etc/kdb.src.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/lib/locale.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/share/keyboard.cramfs.img mounted:
info system:emiting_event:mounted_cramfs_loopbacks:
debug sytem:event_emitted:mounted_cramfs_loopbacks:
info milestone:8.78:fs75:
info system:emiting_event:loaded_modules_dependencies:
debug sytem:event_emitted:loaded_modules_dependencies:
info modules:modprobe:loading module g_file_storage:
info system:emiting_event:loaded_g_file_storage:
debug sytem:event_emitted:loaded_g_file_storage:
info modules:modprobe:loading module fuse:
info system:emiting_event:loaded_fuse:
debug sytem:event_emitted:loaded_fuse:
info hardware:no_wan::WiFi only device. No WAN found
info system:emiting_event:loaded_ppp_async:
info milestone:9.08:fs00:
debug sytem:event_emitted:loaded_ppp_async:
info system:emiting_event:loaded_fakekey:
debug sytem:event_emitted:loaded_fakekey:
info milestone:9.22:fs23:
info system:emiting_event:mounted_varLocal:
debug sytem:event_emitted:mounted_varLocal:
Welcome to Kindle!
kindle login: info milestone:9.28:fs25:
info milestone:9.31:vi00:
info prereg:PRAGMA_QUICK_CHECK_PASSED::sts=0
info display:update:Checking '/opt/eink/images/G112_ED060XD4U2' for overrides:
info system:emiting_event:loaded_touch:
debug sytem:event_emitted:loaded_touch:
info milestone:11.42:vi99:
info display:started:time=11440:
info system:emiting_event:display_ready:
debug sytem:event_emitted:display_ready:
info userstore:run:time=11650,action=start:
info userstore:found_bootup_flag::Found BOOTUP flag file
info battery:charged:cap=83,mV=4001,mAH=1163:
info system:emiting_event:battery_ready:
debug sytem:event_emitted:battery_ready:
info system:emiting_event:mounted_userstore:
debug sytem:event_emitted:mounted_userstore:
info milestone:13.54:fs50:
info milestone:13.58:fs90:
info milestone:13.63:fs99:
info milestone:13.68:sys99:
info system:emiting_event:devcap_ready:
debug sytem:event_emitted:devcap_ready:
info system:emiting_event:dbus_ready:
debug sytem:event_emitted:dbus_ready:
info dbus:check-update:status=2:dbus_ready sent
info hardware:no_wan::WiFi only device. No WAN found
info milestone:15.09:xx00:
info X:load:time=15250:
info X:xorg.conf:Generating xorg.conf:
info X:xorg.conf:xorg.conf generated:
info milestone:16.86:xx50:
info X:starting:time=16920:
info milestone:20.82:xx99:
info X:started:time=20860:
info system:emiting_event:x_setup_ready:
debug sytem:event_emitted:x_setup_ready:
info locale:read:lang=en_GB.utf8,lc_all=en_GB.utf8:Retrieved Language
info system:emiting_event:langpicker_ready:
debug sytem:event_emitted:langpicker_ready:
info blanket_f:module already loaded:splash:
info milestone:22.18:pi00:
info milestone:22.41:pi99:
info system:emiting_event:contentpack_font_ready:
debug sytem:event_emitted:contentpack_font_ready:
info milestone:32.72:fr00:
info milestone:32.82:fr50:
info milestone:32.84:fr51:
info framework:starting:time=33750:
crit lab126_gui_monitor:abnormalstop:job=framework,res=failed,sts=2:
info monitor:writing_file:file=/var/run/upstart/lab126_gui.restarts:
info blanket_f:module already loaded:splash:
warn lab126_gui:restarts=1,max=3:starting lab126_gui:
info milestone:40.23:pi00:
info milestone:40.37:pi99:
info system:emiting_event:contentpack_font_ready:
debug sytem:event_emitted:contentpack_font_ready:
info milestone:46.12:fr00:
info milestone:46.22:fr50:
info milestone:46.23:fr51:
info framework:starting:time=47040:
crit lab126_gui_monitor:abnormalstop:job=framework,res=failed,sts=2:
info monitor:writing_file:file=/var/run/upstart/lab126_gui.restarts:
info blanket_f:module already loaded:splash:
warn lab126_gui:restarts=2,max=3:starting lab126_gui:
info milestone:51.21:pi00:
info milestone:51.39:pi99:
info system:emiting_event:contentpack_font_ready:
debug sytem:event_emitted:contentpack_font_ready:
info milestone:53.23:fr00:
info milestone:53.39:fr50:
info milestone:53.42:fr51:
info framework:starting:time=54770:
crit lab126_gui_monitor:abnormalstop:job=framework,res=failed,sts=2:
info monitor:writing_file:file=/var/run/upstart/lab126_gui.restarts:
info blanket_f:module already loaded:splash:
info monitor:writing_file:file=/var/local/upstart/lab126_gui.restarts:
crit lab126_gui:restarts=3,max=3,reboots=1:rebooting system:
info shutdown:begin:level=6,halt=,special=:
info shutdown:closing password dialog::
info blanket_f:loading blanket module:shutdown:
info shutdown_showimage:screen:splashing screen:reboot
info shutdown_showimage:screen:waiting for reboot screen to come up:
info upstart_f:stopping_job:job=x:
info upstart_f:stopping_job:job=lab126:
info upstart_f:jobs_stopped:elapsed_ms=4640,timeout_ms=45000:
info upstart_f:stopping_job:job=filesystems:
info filesystems_var_local:unmounting font files::
info filesystems_userstore:unmount_userstore:Unmounting UserStore:
info filesystems_var_local:rotate_log:Rotating Logs:
info userstore:run:time=70950,action=stop:
info userstore:filesystem sync done::
info userstore:found_bootup_flag::Found BOOTUP flag file
info filesystems_var_local:filesystem sync done::
info filesystems_var_local:unmount_varLocal:Unmounting VarLocal:
info upstart_f:jobs_stopped:elapsed_ms=3730,timeout_ms=30000:
info shutdown:mounting root filesystem read-only::
info shutdown:syncing disks::
info shutdown:end:level=6,halt=:
[ 74.754334] imx2-wdt imx2-wdt.0: Device shutdown: Expect reboot!
[ 74.760394] Restarting system.
U-Boot 2009.08-lab126 (Aug 05 2014 - 04:37:39)
CPU: Freescale i.MX6 family TO0.0 at 996 MHz
Temperature: 40 C, calibration data 0x5df5515f
mx6sl pll1: 996MHz
mx6sl pll2: 528MHz
mx6sl pll3: 480MHz
mx6sl pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 66000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 198000000Hz
emi_slow clock: 22000000Hz
ddr clock : 396000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
MMC: FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2
Board: Pinot WFO
Boot Reason: [ POR ]
Boot Device: NAND
Board Id: 0272201144120JFX
S/N: 901722
I2C: ready
DRAM: 256 MB
Using default environment
In: serial
Out: serial
Err: serial
Quick Memory Test 0x80000000, 0xfff0000
POST done in 60 ms
Battery voltage: 4001 mV
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at 80800000 ...
Image Name: Linux-3.0.35-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2593852 Bytes = 2.5 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.098489]
[ 0.272450] LPDDR2 MfgId: 0x1 [Samsung]
[ 0.276532]
[ 0.276535] just text: vaddr c013f678, va 0xc013f200 pa 0x801000c3 attr 0x6
[ 0.289084]
[ 0.289087] nmx6sl_wfi_iram: vaddr d084e000, va 0xd084e200 pa 0x904043 attr 0x2
[ 0.297933]
[ 0.297936] mx6sl_ddr: vaddr d0856000, va 0xd0856200 pa 0x905043 attr 0x2
[ 0.306265]
[ 0.306267] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149
[ 0.317106]
[ 0.317108] ANATOP: vaddr f40c8000, va 0xf40c8200 pa 0x20110c3 attr 0x149
[ 0.331459]
[ 0.331462] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149
[ 0.343602]
[ 0.343605] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149
[ 0.354016]
[ 0.354019] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149
[ 0.363917]
[ 0.363919] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149
3.0.35-lab126 #1 PREEMPT Wed Dec 10 13:49:16 PST 2014 armv7l
Press [ENTER] for recovery menu... 0 //dev/mmcblk0p4:
CHS=4/16/104512 size=3424649216 bytes
flag type first last lba first lba size
Partition p1:
0x00 0x0b 16 <large> 16 6688752
CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
BOOTING DEFAULT.
IP-Config: no devices to configure
kinit: Mounted root (ext3 filesystem) readonly.
info sytem:mounted_proc::
info system:mounted_sys::
info system:mounted_dev::
info milestone:6.72:49.1:
info milestone:6.76:49.2:
info milestone:6.79:49.3:
info milestone:6.83:49.4:
info milestone:6.86:49.5:
info sytem:mounted_tmpfs::
info milestone:6.93:sy50:
info system:start:time=6960:
info hardware:no_wan::WiFi only device. No WAN found
info system:config:platform=wario,board=pinot,rev=34,proto=Y,wifi=Y,wan=N:
info milestone:7.11:sy51:
lipc-send-event[808]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[808]: C def:dbusi::Failed to init dbus
lipc-send-event[808]: E def:open::Failed to open LIPC
lipc-send-event[808]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
lipc-send-event[807]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[807]: C def:dbusi::Failed to init dbus
lipc-send-event[807]: E def:open::Failed to open LIPC
lipc-send-event[807]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
info milestone:8.01:sy99:
info system:done:time=8039:
init.exe: sshd main process (819) terminated with status 2
init.exe: sshd main process ended, respawning
crond[821]: crond: crond (busybox 1.17.1) started, log level 8
init.exe: recevent pre-start process (824) terminated with status 1
info system_cramfs_loopbacks:mountingcramfs:Mounting compressed directories filesystem images:
warn system_cramfs_loopbacks:mountpointmissing:Image /lib/firmware/cyttsp.cramfs.img not mounted, non existing mounting point:
info system_cramfs_loopbacks:mounted:Image /usr/share/X11/xkb.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/java/lib/fonts.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /etc/kdb.src.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/lib/locale.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/share/keyboard.cramfs.img mounted:
info system:emiting_event:mounted_cramfs_loopbacks:
debug sytem:event_emitted:mounted_cramfs_loopbacks:
info milestone:8.77:fs75:
info system:emiting_event:loaded_modules_dependencies:
debug sytem:event_emitted:loaded_modules_dependencies:
info modules:modprobe:loading module g_file_storage:
info system:emiting_event:loaded_g_file_storage:
debug sytem:event_emitted:loaded_g_file_storage:
info modules:modprobe:loading module fuse:
info system:emiting_event:loaded_fuse:
debug sytem:event_emitted:loaded_fuse:
info hardware:no_wan::WiFi only device. No WAN found
info system:emiting_event:loaded_ppp_async:
info milestone:9.01:fs00:
debug sytem:event_emitted:loaded_ppp_async:
info system:emiting_event:loaded_fakekey:
debug sytem:event_emitted:loaded_fakekey:
info milestone:9.11:fs23:
info system:emiting_event:mounted_varLocal:
debug sytem:event_emitted:mounted_varLocal:
info milestone:9.17:fs25:
info milestone:9.20:vi00:
Welcome to Kindle!
kindle login: info prereg:PRAGMA_QUICK_CHECK_PASSED::sts=0
info display:update:Checking '/opt/eink/images/G112_ED060XD4U2' for overrides:
info system:emiting_event:loaded_touch:
debug sytem:event_emitted:loaded_touch:
info milestone:11.31:vi99:
info display:started:time=11330:
info system:emiting_event:display_ready:
debug sytem:event_emitted:display_ready:
info userstore:run:time=11540,action=start:
info userstore:found_shutdown_flag::Found SHUTDOWN flag file
info battery:charged:cap=83,mV=4002,mAH=1169:
info system:emiting_event:battery_ready:
debug sytem:event_emitted:battery_ready:
info system:emiting_event:mounted_userstore:
debug sytem:event_emitted:mounted_userstore:
info milestone:12.76:fs50:
info milestone:12.80:fs90:
info milestone:12.85:fs99:
info milestone:12.90:sys99:
info system:emiting_event:devcap_ready:
debug sytem:event_emitted:devcap_ready:
info system:emiting_event:dbus_ready:
debug sytem:event_emitted:dbus_ready:
info dbus:check-update:status=2:dbus_ready sent
info hardware:no_wan::WiFi only device. No WAN found
info milestone:14.01:xx00:
info shutdown:begin:level=6,halt=0,special=factory_reset:
info X:load:time=14190:
info X:xorg.conf:Generating xorg.conf:
info shutdown:closing password dialog::
warn shutdown_showimage:x/blanket is not running:screen not updated:
warn shutdown:splash image not displayed::
info upstart_f:stopping_job:job=x:
info upstart_f:stopping_job:job=lab126:
info X:xorg.conf:xorg.conf generated:
info milestone:16.54:xx50:
info X:starting:time=16720:
info upstart_f:jobs_stopped:elapsed_ms=4300,timeout_ms=45000:
info shutdown:factory_reset:starting:
info hardware:no_wan::WiFi only device. No WAN found
info ss_factory_reset:cleaning misc files::
info ss_factory_reset:erasing waveforms::
info upstart_f:stopping_job:job=filesystems:
info filesystems_var_local:unmounting font files::
info filesystems_userstore:unmount_userstore:Unmounting UserStore:
info filesystems_var_local:rotate_log:Rotating Logs:
info userstore:run:time=22980,action=stop:
info userstore:filesystem sync done::
info userstore:found_bootup_flag::Found BOOTUP flag file
info filesystems_var_local:filesystem sync done::
info filesystems_var_local:unmount_varLocal:Unmounting VarLocal:
info upstart_f:jobs_stopped:elapsed_ms=4180,timeout_ms=30000:
info ss_factory_reset:erasing partition:name="userstore" partition=/dev/mmcblk0p4:secure erase from 1044480 of 6688768 sectors
[ 32.555606] mmc0: Got data interrupt 0x00100000 even though no data operation was in progress.
info ss_factory_reset:partition erased successfully:name="userstore" partition=/dev/mmcblk0p4:
info ss_factory_reset:erasing partition:name="/var/local" partition=/dev/mmcblk0p3:overwriting first 4096 of 65536 blocks
info ss_factory_reset:partition erased successfully:name="/var/local" partition=/dev/mmcblk0p3:
info ss_factory_reset:marking system factory-fresh::
info ss_factory_reset:marking system no_transitions for volumd and powerd::
info ss_factory_reset:marking system factory-fresh-authentication::
info ss_factory_reset:completed successfully::
info upstart_f:job_already_stopped:job=filesystems:
info upstart_f:jobs_stopped:elapsed_ms=0,timeout_ms=30000:
info shutdown:mounting root filesystem read-only::
info shutdown:syncing disks::
info shutdown:end:level=6,halt=0:
[ 93.744192] imx2-wdt imx2-wdt.0: Device shutdown: Expect reboot!
[ 93.751376] Restarting system.
U-Boot 2009.08-lab126 (Aug 05 2014 - 04:37:39)
CPU: Freescale i.MX6 family TO0.0 at 996 MHz
Temperature: 42 C, calibration data 0x5df5515f
mx6sl pll1: 996MHz
mx6sl pll2: 528MHz
mx6sl pll3: 480MHz
mx6sl pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 66000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 198000000Hz
emi_slow clock: 22000000Hz
ddr clock : 396000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
MMC: FSL_ESDHC: 0,FSL_ESDHC: 1,FSL_ESDHC: 2
Board: Pinot WFO
Boot Reason: [ POR ]
Boot Device: NAND
Board Id: 0272201144120JFX
S/N: 901722
I2C: ready
DRAM: 256 MB
Using default environment
In: serial
Out: serial
Err: serial
Quick Memory Test 0x80000000, 0xfff0000
POST done in 60 ms
Battery voltage: 4000 mV
Hit any key to stop autoboot: 0
## Booting kernel from Legacy Image at 80800000 ...
Image Name: Linux-3.0.35-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2593852 Bytes = 2.5 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.098508]
[ 0.272454] LPDDR2 MfgId: 0x1 [Samsung]
[ 0.276534]
[ 0.276537] just text: vaddr c013f678, va 0xc013f200 pa 0x801000c3 attr 0x6
[ 0.289088]
[ 0.289091] nmx6sl_wfi_iram: vaddr d084e000, va 0xd084e200 pa 0x904043 attr 0x2
[ 0.297935]
[ 0.297938] mx6sl_ddr: vaddr d0856000, va 0xd0856200 pa 0x905043 attr 0x2
[ 0.306265]
[ 0.306268] mx6sl_iomux: vaddr f40e0000, va 0xf40e0200 pa 0x20110c3 attr 0x149
[ 0.317105]
[ 0.317108] ANATOP: vaddr f40c8000, va 0xf40c8200 pa 0x20110c3 attr 0x149
[ 0.331454]
[ 0.331457] CCM: vaddr f40c4000, va 0xf40c4200 pa 0x20110c3 attr 0x149
[ 0.343600]
[ 0.343603] MMDC_P0: vaddr f41b0000, va 0xf41b0200 pa 0x21110c3 attr 0x149
[ 0.354013]
[ 0.354016] L2: vaddr f2a02000, va 0xf2a02200 pa 0xa02043 attr 0x149
[ 0.363914]
[ 0.363917] arm perif: vaddr f2a00000, va 0xf2a00200 pa 0xa00043 attr 0x149
3.0.35-lab126 #1 PREEMPT Wed Dec 10 13:49:16 PST 2014 armv7l
[ 0.542581] FAT-fs (loop1): bogus number of reserved sectors
[ 1.585658] imx_epdc_fb imx_epdc_fb: Failed to load fw! (err -2) Trying fallback fw
[ 1.633538] panel_get_upd_modes: Unknown waveform mode. Using MODE_07!
Press [ENTER] for recovery menu... 0 /BOOTING DEFAULT.
IP-Config: no devices to configure
kinit: Mounted root (ext3 filesystem) readonly.
info sytem:mounted_proc::
info system:mounted_sys::
info system:mounted_dev::
info milestone:6.25:49.1:
info milestone:6.30:49.2:
info milestone:6.32:49.3:
info milestone:6.36:49.4:
info milestone:6.39:49.5:
info sytem:mounted_tmpfs::
info milestone:6.46:sy50:
info system:start:time=6490:
info hardware:no_wan::WiFi only device. No WAN found
info system:config:platform=wario,board=pinot,rev=34,proto=Y,wifi=Y,wan=N:
info milestone:6.64:sy51:
lipc-send-event[817]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[817]: C def:dbusi::Failed to init dbus
lipc-send-event[817]: E def:open::Failed to open LIPC
lipc-send-event[817]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
lipc-send-event[816]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[816]: C def:dbusi::Failed to init dbus
lipc-send-event[816]: E def:open::Failed to open LIPC
lipc-send-event[816]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
info milestone:7.53:sy99:
info system:done:time=7560:
crond[847]: crond: crond (busybox 1.17.1) started, log level 8
init.exe: sshd main process (845) terminated with status 2
init.exe: sshþ main process endediniþ.exe: recevent pre-start procinfo system_cramfs_loopbacks:mountingcramfs:Mounting compressed directories filesystem images:
warn system_cramfs_loopbacks:mountpointmissing:Image /lib/firmware/cyttsp.cramfs.img not mounted, non existing mounting point:
info system_cramfs_loopbacks:mounted:Image /usr/share/X11/xkb.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/java/lib/fonts.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /etc/kdb.src.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/lib/locale.cramfs.img mounted:
info system_cramfs_loopbacks:mounted:Image /usr/share/keyboard.cramfs.img mounted:
info system:emiting_event:mounted_cramfs_loopbacks:
debug sytem:event_emitted:mounted_cramfs_loopbacks:
info milestone:8.32:fs75:
info system:emiting_event:loaded_modules_dependencies:
debug sytem:event_emitted:loaded_modules_dependencies:
info modules:modprobe:loading module g_file_storage:
info system:emiting_event:loaded_g_file_storage:
debug sytem:event_emitted:loaded_g_file_storage:
info modules:modprobe:loading module fuse:
info system:emiting_event:loaded_fuse:
debug sytem:event_emitted:loaded_fuse:
info hardware:no_wan::WiFi only device. No WAN found
info system:emiting_event:loaded_ppp_async:
info milestone:8.56:fs00:
debug sytem:event_emitted:loaded_ppp_async:
info system:emiting_event:loaded_fakekey:
debug sytem:event_emitted:loaded_fakekey:
info filesystems_var_local:createvarlocal:Creating /var/local filesystem:
Welcome to Kindle!
kindle login: info filesystems_var_local:notransitionsexists:file=/var/local/system/no_transitions:Already exists
info filesystems_var_local:createvarlocalfirstboot:file=/var/local/system/localvar_firstboot:Creating var local first boot file
info milestone:10.24:fs23:
info system:emiting_event:migrate_DB:
debug sytem:event_emitted:migrate_DB:
info filesystems_var_local:createvarlocaldbupgrade:file=/var/local/system/LOCALVAR_DBUPGRADE:Creating var local db upgrade file
info filesystems_var_local:xfsn-deprecate:start:
info milestone:10.31:mdb1:
info milestone:10.34:mdb2:
info DB_MIGRATION:Moving cc db to tmpfs::
info filesystems_var_local:xfsn-deprecate:done:
info milestone:10.39:fs25:
info milestone:10.39:mdb5:
info milestone:10.42:mdb25:
info system:emiting_event:mounted_varLocal:
debug sytem:event_emitted:mounted_varLocal:
info milestone:10.53:vi00:
[ 11.518191] FAT-fs (loop1): bogus number of reserved sectors
info display:update:Checking '/opt/eink/images/G112_ED060XD4U2' for overrides:
info display:update:No waveform found. Extracting waveform from panel.:
info system:emiting_event:loaded_touch:
debug sytem:event_emitted:loaded_touch:
info display:update:Extracted waveform into /var/local/eink/waveforms/320_G112_AA9124_ED060XD4U2_TC.wbf:
info display:update:Copied waveform from /var/local/eink/waveforms/320_G112_AA9124_ED060XD4U2_TC.wrf.gz into /mnt/wfm/waveform_to_use:
info milestone:28.30:vi99:
info display:started:time=28320:
info system:emiting_event:display_ready:
debug sytem:event_emitted:display_ready:
info userstore:run:time=28480,action=start:
info userstore:mntus.param_not_found::mntus.param not found, initializing volume
info userstore:check_us::checking userstore filesystem
info battery:charged:cap=84,mV=4009,mAH=1178:
info system:emiting_event:battery_ready:
debug sytem:event_emitted:battery_ready:
info mntus:fs_error_recover::File system errors recovered
info userstore:create_default::creating userstore system and documents directories I
info system:emiting_event:mounted_userstore:
debug sytem:event_emitted:mounted_userstore:
info milestone:36.37:fs50:
info milestone:36.39:fs90:
info milestone:36.42:fs99:
info milestone:36.44:sys99:
info system:emiting_event:devcap_ready:
debug sytem:event_emitted:devcap_ready:
info system:emiting_event:dbus_ready:
debug sytem:event_emitted:dbus_ready:
info dbus:check-update:status=2:dbus_ready sent
info hardware:no_wan::WiFi only device. No WAN found
info milestone:37.62:xx00:
info X:load:time=37780:
info X:xorg.conf:Generating xorg.conf:
info X:xorg.conf:xorg.conf generated:
info milestone:39.04:xx50:
info X:starting:time=39100:
info milestone:41.41:xx99:
info X:started:time=41450:
info system:emiting_event:x_setup_ready:
debug sytem:event_emitted:x_setup_ready:
info locale:pick::Picking Language
info locale:wait::
info hardware:no_wan::WiFi only device. No WAN found
info board_data_file :/opt/ar6k/target/AR6003/hw2.1.1/bin/wario/pinot/wfo/AR6003_wfo_calfile.bin::
info wifim:enablediv:enabling antenna diversity for wifi...:
[ 52.734570] ath6kl: ath6kl_fetch_board_file: Board calibration file fetched: /opt/ar6k/target/AR6003/hw2.1.1/bin/wario/pinot/wfo/AR6003_wfo_calfile.bin
[ 52.812534] ath6kl: MAC from kernel xx:xx:xx:xx:xx:9A
[ 52.825679] ath6kl: temporary war to avoid sdio crc error
[ 53.226694] ath6kl: host only supports scatter of :1 entries, need: 16
Welcome to Kindle!
kindle login: root
#################################################
# N O T I C E * N O T I C E * N O T I C E #
#################################################
Rootfs is mounted read-only. Invoke mntroot rw to
switch back to a writable rootfs.
#################################################
[root@kindle root]# info locale:set::User Picked Language
info locale:read:lang=en_GB.utf8,lc_all=en_GB.utf8:Set Language
info system:emiting_event:langpicker_ready:
debug sytem:event_emitted:langpicker_ready:
info blanket_f:module already loaded:splash:
info milestone:483.54:pi00:
info milestone:483.70:pi99:
info system:emiting_event:contentpack_font_ready:
debug sytem:event_emitted:contentpack_font_ready:
info milestone:486.22:fr00:
info milestone:486.35:fr50:
info milestone:486.37:fr51:
info framework:starting:time=487720:
info milestone:516.40:fr99:
info framework:started:time=516419,delta=30059:
info blanket_f:loading blanket module:usb:
info blanket_f:unloading blanket module:splash:
info system:emiting_event:framework_ready:
debug sytem:event_emitted:framework_ready:
info stored:started::
info stored:read_in_counters:REBOOTS=0, REBOOT_LIMIT=1, RESTARTS=0, RESTART_LIMIT=5:
info monitor:writing_file:file=/var/run/upstart/stored.restarts:
Retrieved 314 keys for system/daemon/pmond/
[root@kindle root]#
This is the bit where I think the magic happened, I assume it must have a backup firmware image which it has used instead of the shitty useless one it downloaded and applied from Amazon.
Quote:
|
[ 1.585658] imx_epdc_fb imx_epdc_fb: Failed to load fw! (err -2) Trying fallback fw
|
Next steps.....should I leave as-is, update to latest Amazon firmware or Jailbreak current firmware?
Seems I am on firmware version 5.6.1.0.2
First 6 chars of s/n: 901722