U-Boot 1.3.0-rc3-lab126 (Sep 15 2010 - 19:24:53)
CPU: Freescale i.MX35 at 532 MHz
Board: MX35 Luigi [ POR]
WDOG_WCR = 0xff31
WDOG_WMCR = 0x0
Board Id: SP1B000000000000
S/N: B008A0A00472195A
DRAM: 256 MB
Using default environment
In: serial
Out: serial
Err: serial
No ethernet found.
i.MX35 CPU board version 2.0
Net: No ethernet found.
Hit any key to stop autoboot: 0
## Booting image at 87f40400 ...
Image Name: Linux-2.6.26-rt-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2167548 Bytes = 2.1 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
Uncompressing Linux............................................. .................................................. ........................... done, booting the kernel.
boot: C def:bcut:batterycut=1,version=s172597:
2.6.26-rt-lab126 #5 Sat Sep 1 14:28:26 PDT 2012 armv6l
INFO:Using default keypad setting. (not passing "kb_rev" to module)
INFO:Loaded module /lib/modules/mxc_keyb.ko (22508 bytes)
Press [ENTER] for recovery menu... 0 /INFO:Partition table verified for /dev/mmcblk0
INFO:Checking for updates... (auto-pilot mode)
/dev/mmcblk0p4:
CHS=4/16/100167 size=3282272256 bytes
flag type first last lba first lba size
Partition p1:
0x00 0x0b 16 <large> 16 6410672
CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
INFO:Setup loop device /dev/loop0 for /dev/mmcblk0p4 + 8192
INFO:No update*.bin found; no update needed.
INFO:no updates found.
BOOTING DEFAULT.
argc == 9
argv[0]: "kinit"
argv[1]: "console=ttymxc0,115200"
argv[2]: "mem=256M"
argv[3]: "panic=10"
argv[4]: "root=/dev/mmcblk0p1"
argv[5]: "ro"
argv[6]: "ip=none"
argv[7]: "quiet"
argv[8]: "lpj=2555904"
Running ipconfig
argc == 4
argv[0]: "IP-Config"
argv[1]: "-i"
argv[2]: "Linux kinit"
argv[3]: "ip=none"
IP-Config: no devices to configure
kinit: do_mounts
kinit: name_to_dev_t(/dev/mmcblk0p1) = dev(179,1)
kinit: root_dev = dev(179,1)
kinit: /dev/root appears to be a ext3 filesystem
kinit: trying to mount /dev/root on /root with type ext3
kinit: Mounted root (ext3 filesystem) readonly.
Checking for init: /sbin/init
Checking for init: /bin/init
Checking for init: /etc/init
Checking for init: /sbin/init.sysvinit
INIT: version 2.86 booting
system: I rcS:def:starting /etc/rcS.d/S02kdb
system: I S02kdb:def:Setting boot device to mmcblk0
kdb set: 'system/driver/filesystem/DEV_ROOT'
system: I rcS:def:starting /etc/rcS.d/S03udev
system: I S03udev:def:setting up virtual fs for hotplug event handling
system: I S03udev:def:starting the hotplug events dispatcher
system: I S03udev:def:synthesizing initial hotplug events
lipc-send-event[380]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[380]: C def:dbusi::Failed to init dbus
lipc-send-event[380]: E def
pen::Failed to open LIPC
lipc-send-event[380]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
lipc-send-event[477]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[477]: C def:dbusi::Failed to init dbus
lipc-send-event[477]: E def
pen::Failed to open LIPC
lipc-send-event[477]: E def:fail:source=com.lab126.hal, event=audioHS:Sending event failed
system: I rcS:def:starting /etc/rcS.d/S04rootfsresize
system: I S04rootfsresize:def:No rootfs on /dev/mmcblk0p1 resizing needed
system: I rcS:def:starting /etc/rcS.d/S10filesystems
system: I rcS:def:starting /etc/rcS.d/S10hostname
system: I rcS:def:starting /etc/rcS.d/S10network
system: I S10filesystems:def:mounting filesystems
system: I S10hostname:def:setting device hostname
system: I S10network:def:initializing network configuration
iptables-restore: line 1 failed
system: I S10network:def:Installed Firewall
system: I rcS:def:starting /etc/rcS.d/S11chpriority
system: I rcS:def:starting /etc/rcS.d/S11video
Unknown HZ value! (91) Assume 100.
system: W S11chpriority:def:Cannot set priority for IRQ-7
system: I S11video:def:initializing eInk HAL for system use
system: I S11video:def:eink_debug=0
system: I S11video:def:Controller set to broads
system: I rcS:def:starting /etc/rcS.d/S20syslog-ng
system: I S20syslog-ng:def:starting syslog-ng
system: I rcS:def:starting /etc/rcS.d/S21init_time
system: I S21init_time:initboot:time=16040:boot time after init in milliseconds
system: I rcS:def:starting /etc/rcS.d/S45modules
system: I S45modules:def:loading module mwan