[root@kindle root]#
dmesg
Spoiler:
Code:
CPU: ARMv6-compatible processor revision 3 (ARMv6TEJ),
Machine: Amazon MX35 Luigi Board
ATAGS:rev16:str="SP1B000000000000"
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 65536
DMA zone: 48 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 6096 pages, LIFO batch:0
Normal zone: 464 pages used for memmap
Normal zone: 58928 pages, LIFO batch:15
Movable zone: 0 pages used for memmap
CPU0: D VIPT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttymxc0,115200 mem=256M panic=10 root=/dev/mmcblk0p1 ro ip=none quiet lpj=2555904
MXC IRQ initialized
PID hash table entries: 1024 (order: 10, 4096 bytes)
MXC GPT timer initialized, rate = 16000000
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 255796KB available (3036K code, 276K data, 620K init)
Calibrating delay loop (skipped)... 511.18 BogoMIPS preset
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 492 bytes
NET: Registered protocol family 16
L2X0 cache controller enabled
CPU is i.MX35 Revision 2.0
Board ID and Serial Number driver for Lab126 boards version 1.0
MX35 Board id - SP1B000000000000
MX35 Reset Control and Status Register: 0x26400000
MXC GPIO hardware
mxc_pwm_device registered
Using SDMA I.API
MXC DMA API initialized
MXC PWM Initialized
CSPI: mxc_spi-0 probed
CSPI: mxc_spi-1 probed
MXC I2C driver
MXC I2C driver
clk: Unable to get requested clock: dfm_clk
PMIC Light driver loading...
Registering the PMIC Protocol Driver
mc13892 Rev 2.1 FinVer 2 detected
usbdr_early_portsc1_read: 0
PMIC ADC start probe
PMIC Light successfully loaded
mc13892 Rev 2.1 FinVer 2 detected
MC13892 regulator successfully probed
Device spi1.0 probed
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
Initializing MX35 DVFS on MC13892 Finid: 2
Power Button Debounce Settings: 0x401000
MX35 Luigi working points: 2
Initializing Luigi WiFi
Initializing MX35 Luigi/Shasta Accessory Port
No Accessory Found
Luigi/Freescale MX35 CPUFREQ driver
usb: Host 2 host (serial) registered
usb: DR gadget (utmi) registered
NetWinder Floating Point Emulator V0.97 (double precision)
msgmni has been set to 499
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Amazon MX35 Luigi Power Button Driver
Serial: MXC Internal UART driver
mxcintuart.0: ttymxc0 at MMIO 0x43f90000 (irq = 45) is a Freescale MXC
console [ttymxc0] enabled
mxcintuart.1: ttymxc1 at MMIO 0x43f94000 (irq = 32) is a Freescale MXC
mxcintuart.2: ttymxc2 at MMIO 0x5000c000 (irq = 18) is a Freescale MXC
loop: module loaded
mc13892 rtc probe start
pmic_rtc pmic_rtc.1: rtc core: registered pmic_rtc as rtc0
mc13892 rtc probe succeed
i2c /dev entries driver
MXC WatchDog Driver 2.0
MXC Watchdog # 0 Timer: initial timeout 127 sec
MXC Watchdog: Started 10000 millisecond watchdog refresh
PMIC Character device: successfully loaded
mxsdhci: MXC Secure Digital Host Controller Interface driver
mxsdhci: MXC SDHCI Controller Driver.
mmc0: Using 8-bit bus width
mmc0: SDHCI detect irq 65 irq 7 INTERNAL DMA
mxsdhci: MXC SDHCI Controller Driver.
mmc1: SDHCI detect irq 66 irq 8 INTERNAL DMA
mxsdhci: MXC SDHCI Controller Driver.
emmc: I def:mmcpartinfo:vendor=samsung, mode=open-ended, host=mmc0:
mmc2: SDHCI detect irq 140 irq 9 INTERNAL DMA
mmc0: Using block addressing
ext_csd: 0x3
mmc0: new high speed MMC card at address 0001
mmcblk0: mmc0:0001 M4G1EM 3907584KiB
mmcblk0:<6>Registered led device: pmic_ledsr
Registered led device: pmic_ledsg
p1 p2 p3 p4
Registered led device: pmic_ledsb
Advanced Linux Sound Architecture Driver Version 1.0.16.
ASoC version 0.13.2
wm8960: WM8960 Audio Codec 0.1
DMA Sound Buffers Allocated:UseIram=1 buf->addr=10001000 buf->area=d0820000 size=65536
DMA Sound Buffers Allocated:UseIram=1 buf->addr=8fa80000 buf->area=fde01000 size=65536
asoc: WM8960 <-> imx-i2s-1-0 mapping ok
ALSA device list:
#0: mx35luigi (WM8960)
nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
mxc_rtc mxc_rtc.0: rtc core: registered mxc_rtc as rtc1
mmc1: queuing CIS tuple 0x01 length 3
mmc1: queuing CIS tuple 0x1a length 5
mmc1: queuing CIS tuple 0x1b length 8
mmc1: queuing CIS tuple 0x14 length 0
mmc1: queuing CIS tuple 0x80 length 1
mmc1: queuing CIS tuple 0x81 length 1
mmc1: queuing CIS tuple 0x82 length 1
mmc1: new SDIO card at address 0001
mxc_rtc: saved=0x0 boot=0x8
boot: C def:bcut:batterycut=1,version=s061168:
Real Time clock Driver v1.0
kernel: W perf:kernel:kernel_loaded=1.54 seconds:
boot globals: I reserved 4096 bytes at 0x8FFFF000
boot globals: I warm restart flag not set (0x00000100)
boot globals: I invalid, clearing
boot globals: I setting kernel_boot_flag = 64
boot globals: I setting warm restart to 0x646C6F63
Static Power Management for Freescale i.MX35
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 3
pmic_rtc pmic_rtc.1: setting system clock to 1970-01-01 00:00:08 UTC (8)
Freeing init memory: 620K
mxc_keyb: I def:drv::Keypad driver loaded
input: mxckpd as /devices/virtual/input/input0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on mmcblk0p2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
eink_fb: I ipu_controller_type:def:Detected broadsheet controller
eink_fb: I bs_cmd_ld_img_upd_data_which:def:temp=24C:from pmic
eink_fb: I bs_cmd_ld_img_upd_data_which:def:temp=24C:from pmic
eink_fb: I bs_cmd_ld_img_upd_data_which:def:temp=24C:from pmic
eink_fb: I EINKFB_PROBE:def:fb0 using 708K of RAM for framebuffer
eink_fb: I bs_cmd_ld_img_upd_data_which:def:temp=25C:from pmic
eink_fb: I bs_cmd_ld_img_upd_data_which:def:temp=25C:from pmic
mwan: I mwan_init:init:mario WAN hardware driver 1.2.0
ARC USBOTG Device Controller driver (10/08/2009)
kernel: I perf:usb:usb_gadget_loaded=18.05 seconds:
g_file_storage gadget: File-backed Storage Gadget, version: 7 August 2007
g_file_storage gadget: Number of LUNs=1
fsl-usb2-udc: bind to driver g_file_storage
fuse init (API version 7.9)
mxc_keyb: I def:drv::Keypad driver loaded
input: mxckpd as /devices/virtual/input/input1
fiveway: I def:probe0::Starting...
fiveway: I def:probe_done::GPIOs and IRQs have been set up
input: fiveway as /devices/virtual/input/input2
fiveway: I def:drv::Fiveway driver loaded
volume: I def:probe0::Starting...
volume: I def:probe_done::GPIOs and IRQs have been set up
input: volume as /devices/virtual/input/input3
volume: I def:drv::Volume key driver loaded
No USB/Charger found ... entering low power idle
Charger: Turning on CPUFreq
ar6000: Shasta Atheros Ar6000 WiFi Driver
ar6000_probe: initializing!
kernel: I perf:wifi:wifi_driver_loaded=37.48 seconds:
AR6000 Reg Code = 0x40000060
Accessory port enable
mxc_keyb: I def:unlocked1:status=unlocked:
fiveway: I def:unlock1:status=unlocked:
No Accessory Found
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 35, io mem 0x53ff4400
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb 1-1: new full speed USB device using fsl-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usbserial
usbserial: USB Serial Driver core
usbserial: USB Serial support registered for GSM modem (1-port)
option 1-1:1.0: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
option 1-1:1.1: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
usbcore: registered new interface driver option
option: USB Driver for GSM modems: v0.7.2
EXT3 FS on mmcblk0p1, internal journal
mwan: I init_modem_type:smt:type=3:setting modem type
PPP generic driver version 2.4.2
Enter LPM
...
flashing):x1=0,x2=600,y1=768,y2=800
unregistered gadget driver 'g_file_storage'
usb0: Ethernet Gadget, version: May Day 2005
usb0: using fsl-usb2-udc, OUT ep1out IN ep1in STATUS ep2in
usb0: MAC ee:99:99:00:00:00
usb0: HOST MAC ee:99:99:00:00:00
usb0: RNDIS ready
fsl-usb2-udc: bind to driver ether
eink_fb: I bs_cmd_ld_img_upd_data_which:def:temp=25C:from pmic
Charger: Setting CPU Frequeny to 512MHz
Connected to a HIGH speed Host
usb0: full speed config #1: 100 mA, Ethernet Gadget, using CDC Ethernet
battery: I def:avg:Average_mAH_usage=9mAH, time=170seconds:
Accessory port disabled!
mxc_keyb: I def:locked2:status=locked:
fiveway: I def:locked2:status=locked:
eink_fb: I bs_cmd_ld_img_upd_data_which:def:temp=26C:from pmic
Okay nothing there about it... at all...
must be post boot. and not recorded in that log.
need more logs...