This is the output:
Code:
Rebooting in 1 second...
Restarting system.
EXT3-fs error (device mmcblk0p1): ext3_find_entry: reading directory #3213 offset 1
EXT3-fs error (device mmcblk0p1): ext3_find_entry: reading directory #3213 offset 0
Unhandled fault: external abort on non-linefetch (0x008) at 0x00020048
U-Boot 1.3.0-rc3-lab126 (Apr 6 2011 - 17:12:22)
CPU: Freescale i.MX35 at 532 MHz
Board: MX35 Luigi [ POR]
WDOG_WCR = 0xff31
WDOG_WMCR = 0x0
Board Id: SP1B000000000000
S/N: ***
DRAM: 256 MB
Using default environment
In: serial
Out: serial
Err: serial
No ethernet found.
i.MX35 CPU board version 2.0
Net: No ethernet found.
Hit any key to stop autoboot: 0
## Booting image at 87f40400 ...
Image Name: Linux-2.6.26-rt-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2168732 Bytes = 2.1 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Starting kernel ...
Uncompressing Linux.......................................................................................................................... done, booting the kernel.
boot: I def:rbt:reset=user_reboot:
2.6.26-rt-lab126 #5 Wed Apr 6 17:13:11 PDT 2011 armv6l
INFO:Using default keypad setting. (not passing "kb_rev" to module)
INFO:Loaded module /lib/modules/mxc_keyb.ko (22508 bytes)
Press [ENTER] for recovery menu... 0 /INFO:Partition table verified for /dev/mmcblk0
INFO:Checking for updates... (auto-pilot mode)
/dev/mmcblk0p4:
CHS=4/16/100167 size=3282272256 bytes
flag type first last lba first lba size
Partition p1:
0x00 0x0b 16 <large> 16 6410672
CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
INFO:Setup loop device /dev/loop0 for /dev/mmcblk0p4 + 8192
INFO:No update*.bin found; no update needed.
INFO:no updates found.
BOOTING DEFAULT.
argc == 9
argv[0]: "kinit"
argv[1]: "console=ttymxc0,115200"
argv[2]: "mem=256M"
argv[3]: "panic=10"
argv[4]: "root=/dev/mmcblk0p1"
argv[5]: "ro"
argv[6]: "ip=none"
argv[7]: "quiet"
argv[8]: "lpj=2555904"
Running ipconfig
argc == 4
argv[0]: "IP-Config"
argv[1]: "-i"
argv[2]: "Linux kinit"
argv[3]: "ip=none"
IP-Config: no devices to configure
kinit: do_mounts
kinit: name_to_dev_t(/dev/mmcblk0p1) = dev(179,1)
kinit: root_dev = dev(179,1)
kinit: /dev/root appears to be a ext3 filesystem
kinit: trying to mount /dev/root on /root with type ext3
kinit: Mounted root (ext3 filesystem) readonly.
Checking for init: /sbin/init
Checking for init: /bin/init
Checking for init: /etc/init
Checking for init: /sbin/init.sysvinit
INIT: version 2.86 booting
system: I rcS:def:starting /etc/rcS.d/S02kdb
system: I S02kdb:def:Setting boot device to mmcblk0
kdb set: 'system/driver/filesystem/DEV_ROOT'
system: I rcS:def:starting /etc/rcS.d/S03udev
system: I S03udev:def:setting up virtual fs for hotplug event handling
system: I S03udev:def:starting the hotplug events dispatcher
system: I S03udev:def:synthesizing initial hotplug events
lipc-send-event[380]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[380]: C def:dbusi::Failed to init dbus
lipc-send-event[380]: E def:open::Failed to open LIPC
lipc-send-event[380]: E def:fail:source=com.lab126.hal, event=usbPlugIn:Sending event failed
lipc-send-event[476]: E lipc:con::Connection error(Failed to connect to socket /var/run/dbus/system_bus_socket: No such file or directory)
lipc-send-event[476]: C def:dbusi::Failed to init dbus
lipc-send-event[476]: E def:open::Failed to open LIPC
lipc-send-event[476]: E def:fail:source=com.lab126.hal, event=audioHS:Sending event failed
system: I rcS:def:starting /etc/rcS.d/S04rootfsresize
system: I S04rootfsresize:def:No rootfs on /dev/mmcblk0p1 resizing needed
system: I rcS:def:starting /etc/rcS.d/S10filesystems
system: I rcS:def:starting /etc/rcS.d/S10hostname
system: I rcS:def:starting /etc/rcS.d/S10network
system: I S10filesystems:def:mounting filesystems
system: I S10hostname:def:setting device hostname
system: I S10network:def:initializing network configuration
system: I S10network:def:Installed Firewall
system: I rcS:def:starting /etc/rcS.d/S11chpriority
system: I rcS:def:starting /etc/rcS.d/S11video
Unknown HZ value! (90) Assume 100.
system: W S11chpriority:def:Cannot set priority for IRQ-7
system: I S11video:def:initializing eInk HAL for system use
system: I S11video:def:eink_debug=0
system: I S11video:def:Controller set to broads
system: I rcS:def:starting /etc/rcS.d/S20syslog-ng
system: I S20syslog-ng:def:starting syslog-ng
system: I rcS:def:starting /etc/rcS.d/S21init_time
system: I S21init_time:initboot:time=16070:boot time after init in milliseconds
system: I rcS:def:starting /etc/rcS.d/S45modules
system: I S45modules:def:loading module mwan
system: I S45modules:def:loading module g_file_storage
system: I S45modules:def:loading module fuse
system: I S45modules:def:loading module uinput
system: I S45modules:def:loading module mxc_keyb
system: I S45modules:def:loading module fiveway
system: I S45modules:def:loading module volume
system: I rcS:def:starting /etc/rcS.d/S50system
mount: mount point /proc/bus/usb does not exist
system: I rcS:def:starting /etc/rcS.d/S55scroll
system: I S55scroll:def:skipping; no luigi-based work to do here
system: I rcS:def:starting /etc/rcS.d/S70ethernet
system: I rcS:def:starting /etc/rcS.d/S70userstore
system: I S70ethernet:def:not enet
system: I S70ethernet:def:not usbnet
system: I S70userstore:def:Found SHUTDOWN flag file
system: I rcS:def:starting /etc/rcS.d/S90video
system: I S90video:def:initializing eInk HAL for rootfs use
INIT: Entering runlevel: 2
system: I lifeguard:def:starting eInk HAL lifeguard
system: I S40diags:def:not starting Diagnostic Services
system: I S40diags:def:/mnt/base-us/ENABLE_DIAGS does not exist, forcing diagnostic disable
system: I S50battcheck:def:running
Sat Jul 31 00:27:23 2010 INFO:battery voltage: 4036 mV
Sat Jul 31 00:27:23 2010 INFO:battery charge: 94%
system: I S50battcheck:def:current voltage = 4044mV
Sat Jul 31 00:27:23 2010 INFO:battery charge: 94%
Sat Jul 31 00:27:23 2010 INFO:battery voltage: 4036 mV
Sat Jul 31 00:27:23 2010 INFO:battery current: -246 mA
system: I S50battcheck:def:gasgauge capacity=94% volts=4036 mV current=-246 mA
system: I S50battcheck:def:Waiting for 3460mV or 4%
system: I S50battcheck:def:battery sufficient, booting to normal runlevel
INIT: Switching to runlevel: 5
INIT: Sending processes the TERM signal
system: I wifi:def:WiFi Device mac = 28:EF:01:4F:27:8B
Platform set to SHASTA_NATIVEMMC-SDIO
Platform Setup Script is: /opt/ar6k/host/support/platformscripts/plat_SHASTA_NATIVEMMC-SDIO.sh
Image path: /sbin
No debug record limit set
Load Board Data from /opt/ar6k/target/AR6002/hw2.0/bin/lab126_15dBm_nodiv_WWR_CTL.bin
Updating MAC address
BMI Set App Start (address: 0x913950)
BMI Bit-Wise (OR) modify Register (address: 0x500410, orig:0x8, new: 0x9, mask:0x1)
BMI Write compressed Memory (address: 0x502070, filename: /opt/ar6k/target/AR6002/hw2.0/bin/athwlan.bin.z77)
BMI Write Memory (address: 0x52d6d0, filename: /opt/ar6k/target/AR6002/hw2.0/bin/data.patch.hw2_0.bin)
BMI Write Memory (address: 0x500418, value: 0x52d6d0)
BMI Done
system: I wifi:def:loadAR6000=finished, args=():
system: I wpa_supplicant:def:wpa supplicant started
system: I S30network:def:initializing network configuration
system: I S30network:def:Installed Firewall
system: I S60dbus:def:starting system message bus
Failed to start message bus: Could not get UID and GID for username "messagebus"
Starting Process Monitoring Daemon: Retrieved 127 keys for system/daemon/pmond/
Starting Power Management Daemon: com.lab126.pmond failed to open lipc for start event
system: I S70cmd:def:starting CMD daemon
com.lab126.pmond failed to open lipc for start event
system: I S70wifid:def:starting wifid
com.lab126.pmond failed to open lipc for start event
system: I S75phd:def:Starting Phone-Home Daemon
com.lab126.pmond failed to open lipc for start event
system: I S76mcsd:def:starting MCS server
com.lab126.pmond failed to open lipc for start event
system: I S80volumd:def:starting Volume daemon
com.lab126.pmond failed to open lipc for start event
system: I S82usbnet:def:usbnet is disabled
system: I S85audio:def:initializing audio driver defaults
No state is present for card mx35luigi
system: I S85audio:def:starting audio server
com.lab126.pmond failed to open lipc for start event
system: I S87ttsd:def:starting TTS daemon
com.lab126.pmond failed to open lipc for start event
system: I S90cron:def:starting crond
Battery Level: 94%
Sat Jul 31 00:27:34 2010 INFO:battery charge: 94%
Starting lipc-daemon: system: I S90tmd:def:Starting Transfer Manager Daemon
com.lab126.pmond failed to open lipc for start event
system: I S94browserd:def:Starting Browser Daemon
com.lab126.pmond failed to open lipc for start event
system: I S95framework:def:starting booklet framework
INIT: Sending processes the TERM signal
system: I K04framework:def:stopping booklet framework
com.lab126.powerd failed to open lipc for state event
system: I K06browserd:def:Stopping Browser Daemon
com.lab126.pmond failed to open lipc for stop event
killall: browserd: no process killed
system: I K09usbnet:def:couldn't stop usbnet
system: I K10cron:def:stopping crond
start-stop-daemon: lseek: Invalid argument
Stopping lipc-daemon: system: I K10tmd:def:Stopping Transfer Manager Daemon
com.lab126.pmond failed to open lipc for stop event
system: I K15audio:def:stopping audio server
com.lab126.pmond failed to open lipc for stop event
system: I K17ttsd:def:stopping TTS daemon
com.lab126.pmond failed to open lipc for stop event
Failed to open LIPC
com.lab126.hal failed to send event usbUnconfigured
com.lab126.volumd failed to open lipc for driveModeState event
sh: 0: unknown operand
system: I K19userstore:def:Found BOOTUP flag file
system: I K25phd:def:Stopping Phone-Home Daemon
com.lab126.pmond failed to open lipc for stop event
Stopping Power Management Daemon: com.lab126.pmond failed to open lipc for stop event
stopped /usr/bin/wpa_supplicant (pid 2019)
system: W wpa_supplicant:def:wpa supplicant stopped
system: I wifi:def:WiFi Device mac = 28:EF:01:4F:27:8B
Platform set to SHASTA_NATIVEMMC-SDIO
Platform Setup Script is: /opt/ar6k/host/support/platformscripts/plat_SHASTA_NATIVEMMC-SDIO.sh
Image path: /sbin
..unloading all
killall: recEvent: no process killed
system: I wifi:def:loadAR6000=finished, args=(unloadall):
Stopping Process Monitoring Daemon: system: I K85dbus:def:stopping system message bus
system: I K90video:def:stopping eInk HAL lifeguard
system: I K99syslog-ng:def:stopping syslog-ng
system: I tinyrot:def::Rotating file /var/log/messages with max size 256
cat: can't open '/var/local/log/nexttosendfile': No such file or directory
/usr/sbin/tinyrot : Signaling syslog
killall: syslog-ng: no process killed
system: W tinyrot:def:Failed to HUP syslog
killall: syslog-ng: no process killed
pmond[2299]: C def:ipc::Failed to init IPC
/usr/sbin/tinyrot : Calculating total size /var/local/log/messages_*.gz
/usr/sbin/tinyrot : Total size of /var/local/log/messages_*.gz is 165kb
system: I tinyrot:def::Rotating file /var/log/odotlite with max size 4048
system: I tinyrot:def::No file to rotate: /var/log/odotlite
Halting in 1 second...
Power down.
EXT3-fs error (device mmcblk0p1): ext3_find_entry: reading directory #3213 offset 0
EXT3-fs error (device mmcblk0p1): ext3_find_entry: reading directory #3213 offset 1