
[root@(none) interactive]# cat /proc/cpuinfo 
Processor       : ARMv7 Processor rev 10 (v7l)
BogoMIPS        : 790.52
Features        : swp half thumb fastmult vfp edsp neon vfpv3 
CPU implementer : 0x41
CPU architecture: 7
CPU variant     : 0x2
CPU part        : 0xc09
CPU revision    : 10

Hardware        : Freescale i.MX 6SoloLite NTX Board
Revision        : 60200
Serial          : 2d3899d4df667727


[root@(none) interactive]# ls
go_hispeed_load  hispeed_freq     irq_scaling      min_sample_time  timer_rate
[root@(none) interactive]# cat go_hispeed_load 
95
[root@(none) interactive]# cat hispeed_freq 
996000
[root@(none) interactive]# cat irq_scaling 
Change irq setting by echo a data, format: 0xAABBBC, AA:irq number, BBB:up_threshold, C:enable
irq number: 0x29, up_threshold 0x0, disabled
irq number: 0x2a, up_threshold 0x28, disabled
irq number: 0x2b, up_threshold 0x0, disabled
irq number: 0x2a, up_threshold 0x28, enabled
irq number: 0x2b, up_threshold 0x0, enabled
irq number: 0x36, up_threshold 0x4, enabled
irq number: 0x37, up_threshold 0x4, enabled
irq number: 0x38, up_threshold 0x4, enabled
irq number: 0x39, up_threshold 0x4, enabled
irq number: 0x47, up_threshold 0x4, enabled
irq number: 0x4b, up_threshold 0xa, enabled
irq number: 0x96, up_threshold 0x4, enabled
[root@(none) interactive]# cat min_sample_time 
20000
[root@(none) interactive]# cat timer_rate 
50000
[root@(none) interactive]# cd /proc/cpu/
[root@(none) cpu]# ls
alignment
[root@(none) cpu]# cat alignment 
User:           0
System:         0
Skipped:        0
Half:           0
Word:           0
DWord:          0
Multi:          0
User faults:    2 (fixup)
[root@(none) cpu]# 


cd /sys/devices/system/cpu
[root@(none) cpu]# ls
cpu0        cpufreq     kernel_max  offline     online      possible    present
[root@(none) cpu]# cd cpu0
[root@(none) cpu0]# ls
cpufreq
[root@(none) cpu0]# cd cpufreq/
[root@(none) cpufreq]# ls
affected_cpus                  related_cpus                   scaling_governor
cpuinfo_cur_freq               scaling_available_frequencies  scaling_max_freq
cpuinfo_max_freq               scaling_available_governors    scaling_min_freq
cpuinfo_min_freq               scaling_cur_freq               scaling_setspeed
cpuinfo_transition_latency     scaling_driver                 stats
[root@(none) cpufreq]# cat cpuinfo_max_freq 
996000
[root@(none) cpufreq]# cat cpuinfo_min_freq 
396000
[root@(none) cpufreq]# cat cpuinfo_cur_freq 
396000
[root@(none) cpufreq]# cat scaling_available_frequencies 
996000 396000 
[root@(none) cpufreq]# cat scaling_available_governors 
interactive conservative ondemand userspace powersave performance 
[root@(none) cpufreq]# cat scaling_governor 
interactive


[root@(none) cpu0]# cd cpufreq/

[root@(none) cpufreq]# ls
affected_cpus                  related_cpus                   scaling_governor
cpuinfo_cur_freq               scaling_available_frequencies  scaling_max_freq
cpuinfo_max_freq               scaling_available_governors    scaling_min_freq
cpuinfo_min_freq               scaling_cur_freq               scaling_setspeed
cpuinfo_transition_latency     scaling_driver                 stats
[root@(none) cpufreq]# echo 100000 >scaling_min_freq 
[root@(none) cpufreq]# echo 100000 >cpuinfo_min_freq 
-sh: can't create cpuinfo_min_freq: Permission denied



/////////////////


dmesg


MU : set_current_time2register : second is 1435070687, hour is 398630
PMU:STATUS= 7: IBAT= -54: VSYS= 4148000: VBAT= 4152600: DSOC= 9711: RSOC= 9700: cc_delta=69: rrf= 0
PMU: mainFlowOfLowVoltage :     Noxx : cc_delta_cap is -4, cc_delta_cap_now is -12, last_cc_delta_cap is -9
PMU: mainFlowOfLowVoltage :     Noxx : temp_cc_delta_cap is -1, after temp_cc_delta_cap_mas is -119, cc_cap_mas -6796
PMU: mainFlowOfLowVoltage :     No9 :Cap is 9777 , low_rate is 93, dsoc is 9708, capnow is 9800, capzero is 73, delta cc is -3, delta cc ori is -4
PMU: mainFlowOfLowVoltage :     No10 :temp_mas is -510, offset_mas is -391, value is -372, final value is -3
PMU : set_current_time2register : second is 1435070716, hour is 398630
PMU:STATUS= 7: IBAT= -55: VSYS= 4146500: VBAT= 4152000: DSOC= 9708: RSOC= 9700: cc_delta=69: rrf= 0
drivers/input/keyboard/tle4913_keypad.c(79): gpio140,val=0
ghost point detected. discard!
ghost point detected. discard!
TPS65185 temprature data = 0x17,23
wl_iw_detach thr:5914 terminated OK
wl_iw_bt_release thr:5915 terminated OK
dhd_detach thr:5918 terminated OK
dhd_detach thr:5916 terminated OK
dhd_detach thr:5917 terminated OK
Wifi / BT power control 0
_ntx_wifi_power_ctrl() end.
cpufreq_save_default_governor():save policy "interactive"
cpufreq_set_governor():set policy "performance"
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
Freezing user space processes ... freeze 1!!!!!!!!!!!!!!!!!!!!
(elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
PM: Entering mem sleep
Suspending console(s) (use no_console_suspend to debug)
udc suspend begins
PMU: ricoh61x_battery_suspend START ================================================================================
ricoh619-battery ricoh619-battery: sleep entry time : 1435070726 secs
PMU: cc_sum = 7638: cc_cap_res= 27: cc_cap_mas = -2001404416
PMU: cc_cap_offset= -27: 
PMU : ricoh61x_battery_suspend : Suspend : temp_cc_delta_cap_mas is -1352, cc_delta is -7638, last_cc_delta_cap_mas is -6796
PMU FG_RESET : calc_capacity_2 : capacity 9700 init_pswr 97 cc_delta 0
PMU: ricoh61x_battery_suspend status(7), rrf(0), suspend_soc(9708), suspend_cc(0)
PMU: ricoh61x_battery_suspend DSOC(9708), init_pswr(97), cc_delta(-14)
PMU : set_current_time2register : second is 1435070726, hour is 398630
PMU FG_RESET : calc_capacity_2 : capacity 9700 init_pswr 97 cc_delta 0
PMU: ricoh61x_battery_suspend : STATUS(7), DSOC(9708), RSOC(9700), init_pswr*100(9700), cc_delta(0) ====================
PMU: ricoh61x_battery_suspend : fl_current(0), slp_state(1), sus_current(1900), hiber_current(889)
[zForce_ir_touch_recv_data-224] command Deactivate ...
PM: suspend of devices complete after 302.473 msecs
PM: late suspend of devices complete after 0.276 msecs
PM: early resume of devices complete after 0.136 msecs
[zForce_ir_touch_recv_data-259] command BootComplete (0)...
[zForce_ir_touch_recv_data-227] command Activate (0) ...
[zForce_ir_touch_recv_data-236] command Resolution (0) ...
PMU: ricoh61x_battery_resume START ================================================================================
ricoh619-battery ricoh619-battery: sleep exit time : 1435070771 secs
PMU : ricoh61x_battery_resume :         suspend_period_time is 45, sleepExitTime is 1435070771 sleepEntryTime is 1435070726 ==========
[zForce_ir_touch_recv_data-262] command Frequency (0) ...
[zForce_ir_touch_recv_data-245] command Configuration ...
PMU calc_capacity_in_period 1%FACAP(54360)[mAs], cc_sum(172)[mAs], cc_sum_dec(-172)
PMU: ricoh61x_battery_resume : Discharge Processing (rrf=0)
PMU : calc_cc_value_by_sleepPeriod : delta_cap is 158438 [uAs], Period is 45 [s], fa_cap is 1510 [mAh], delta_soc is 0 [0.01%], offset is 158438 [uAs]
PMU: calc_soc_by_currentMethod Hibernate(S/W) hiber_current(889), cc_delta(0) ----------
PMU : calc_soc_by_currentMethod : slp_state is 1, soc is 9708 [0.01%]  ----------
PMU : calc_soc_by_voltageMethod : VBAT is 4152600 [uV], soc is 9900 [0.01%] ----------
PMU: ricoh61x_battery_resume : soc_current(9708), soc_voltage(9900), Diff(-192) ==========
PMU: update_rsoc_on_currentMethod : Current Method. state(7), dsoc(9708), rsoc(9700), init_pswr(97), cc_delta(0) ----------
PMU FG_RESET : calc_capacity : capacity 97 init_pswr 97 cc_delta 0
PMU:check_charge_status_2 Resume Sus_soc(9708), cc(0)
PMU : set_current_time2register : second is 1435070771, hour is 398630
drivers/input/keyboard/tle4913_keypad.c(79): gpio140,val=1
PMU FG_RESET : calc_capacity_2 : capacity 9700 init_pswr 97 cc_delta 0
PMU: ricoh61x_battery_resume : STATUS(7), DSOC(9708), RSOC(9700), init_pswr*100(9700), cc_delta(0) ====================
USB Gadget resume begins
fsl_udc_resume, Wait for wakeup thread finishes
PM: resume of devices complete after 546.383 msecs
PM: Finishing wakeup.
Restarting tasks ... done.
cpufreq_set_governor():set policy "interactive"
cpufreq_restore_default_governor():restore policy "interactive"
restore vcom from -2300mV to -2300mV
TPS65185 temprature data = 0x17,23
mmc2: card 0001 removed
PMU: mainFlowOfLowVoltage :     Noxx : cc_delta_cap is -2, cc_delta_cap_now is 0, last_cc_delta_cap is 0
PMU: mainFlowOfLowVoltage :     Noxx : temp_cc_delta_cap is -2, after temp_cc_delta_cap_mas is -266, cc_cap_mas 275
PMU: mainFlowOfLowVoltage :     No9 :Cap is 9706 , low_rate is 100, dsoc is 9706, capnow is 9720, capzero is 64, delta cc is -2, delta cc ori is -2
PMU: mainFlowOfLowVoltage :     No10 :temp_mas is -266, offset_mas is 0, value is -200, final value is -2
PMU : set_current_time2register : second is 1435070772, hour is 398630
PMU:STATUS= 7: IBAT= -18: VSYS= 4142000: VBAT= 4151400: DSOC= 9706: RSOC= 9700: cc_delta=0: rrf= 0
PMU: mainFlowOfLowVoltage :     Noxx : cc_delta_cap is -1, cc_delta_cap_now is -1, last_cc_delta_cap is 0
PMU: mainFlowOfLowVoltage :     Noxx : temp_cc_delta_cap is 0, after temp_cc_delta_cap_mas is -266, cc_cap_mas -628
PMU: mainFlowOfLowVoltage :     No9 :Cap is 9786 , low_rate is 92, dsoc is 9706, capnow is 9800, capzero is 64, delta cc is 0, delta cc ori is -1
PMU: mainFlowOfLowVoltage :     No10 :temp_mas is -766, offset_mas is -500, value is -92, final value is 0
PMU : set_current_time2register : second is 1435070801, hour is 398630
PMU:STATUS= 7: IBAT= -20: VSYS= 4156000: VBAT= 4159000: DSOC= 9706: RSOC= 9700: cc_delta=0: rrf= 0
[drivers/input/touchscreen/zforce_i2c.c-688] zforce_i2c_close()
[zForce_ir_touch_recv_data-224] command Deactivate ...
[drivers/input/touchscreen/zforce_i2c.c-672] zforce_i2c_open()
[zForce_ir_touch_recv_data-227] command Activate (0) ...
[zForce_ir_touch_recv_data-236] command Resolution (0) ...
[zForce_ir_touch_recv_data-262] command Frequency (0) ...
[zForce_ir_touch_recv_data-245] command Configuration ...
[drivers/input/touchscreen/zforce_i2c.c-688] zforce_i2c_close()
[zForce_ir_touch_recv_data-224] command Deactivate ...
[drivers/input/touchscreen/zforce_i2c.c-672] zforce_i2c_open()
[zForce_ir_touch_recv_data-227] command Activate (0) ...
[zForce_ir_touch_recv_data-236] command Resolution (0) ...
[zForce_ir_touch_recv_data-262] command Frequency (0) ...
[zForce_ir_touch_recv_data-245] command Configuration ...
PMU: mainFlowOfLowVoltage :     Noxx : cc_delta_cap is -4, cc_delta_cap_now is -4, last_cc_delta_cap is -1
PMU: mainFlowOfLowVoltage :     Noxx : temp_cc_delta_cap is -1, after temp_cc_delta_cap_mas is -223, cc_cap_mas -2508
PMU: mainFlowOfLowVoltage :     No9 :Cap is 9746 , low_rate is 96, dsoc is 9703, capnow is 9770, capzero is 74, delta cc is -3, delta cc ori is -4
PMU: mainFlowOfLowVoltage :     No10 :temp_mas is -679, offset_mas is -456, value is -384, final value is -3
PMU : set_current_time2register : second is 1435070830, hour is 398630
PMU:STATUS= 7: IBAT= -61: VSYS= 4151250: VBAT= 4148000: DSOC= 9703: RSOC= 9700: cc_delta=0: rrf= 0
[drivers/input/touchscreen/zforce_i2c.c-688] zforce_i2c_close()
[zForce_ir_touch_recv_data-224] command Deactivate ...
[drivers/input/touchscreen/zforce_i2c.c-672] zforce_i2c_open()
[zForce_ir_touch_recv_data-227] command Activate (0) ...
[zForce_ir_touch_recv_data-236] command Resolution (0) ...
[zForce_ir_touch_recv_data-262] command Frequency (0) ...
[zForce_ir_touch_recv_data-245] command Configuration ...
TPS65185 temprature data = 0x17,23
[drivers/input/touchscreen/zforce_i2c.c-688] zforce_i2c_close()
[zForce_ir_touch_recv_data-224] command Deactivate ...
[drivers/input/touchscreen/zforce_i2c.c-672] zforce_i2c_open()
[zForce_ir_touch_recv_data-227] command Activate (0) ...
[zForce_ir_touch_recv_data-236] command Resolution (0) ...
[zForce_ir_touch_recv_data-262] command Frequency (0) ...
[zForce_ir_touch_recv_data-245] command Configuration ...
[drivers/input/touchscreen/zforce_i2c.c-688] zforce_i2c_close()
[zForce_ir_touch_recv_data-224] command Deactivate ...
[drivers/input/touchscreen/zforce_i2c.c-672] zforce_i2c_open()
[zForce_ir_touch_recv_data-227] command Activate (0) ...
[zForce_ir_touch_recv_data-236] command Resolution (0) ...
[zForce_ir_touch_recv_data-262] command Frequency (0) ...
[zForce_ir_touch_recv_data-245] command Configuration ...
[drivers/input/touchscreen/zforce_i2c.c-688] zforce_i2c_close()
[zForce_ir_touch_recv_data-224] command Deactivate ...
[drivers/input/touchscreen/zforce_i2c.c-672] zforce_i2c_open()
[zForce_ir_touch_recv_data-227] command Activate (0) ...
[zForce_ir_touch_recv_data-236] command Resolution (0) ...
[zForce_ir_touch_recv_data-262] command Frequency (0) ...
[zForce_ir_touch_recv_data-245] command Configuration ...
[drivers/input/touchscreen/zforce_i2c.c-688] zforce_i2c_close()
[zForce_ir_touch_recv_data-224] command Deactivate ...
[drivers/input/touchscreen/zforce_i2c.c-672] zforce_i2c_open()
[zForce_ir_touch_recv_data-227] command Activate (0) ...
[zForce_ir_touch_recv_data-236] command Resolution (0) ...
[zForce_ir_touch_recv_data-262] command Frequency (0) ...
[zForce_ir_touch_recv_data-245] command Configuration ...
PMU: mainFlowOfLowVoltage :     Noxx : cc_delta_cap is -6, cc_delta_cap_now is -9, last_cc_delta_cap is -4
PMU: mainFlowOfLowVoltage :     Noxx : temp_cc_delta_cap is -1, after temp_cc_delta_cap_mas is -136, cc_cap_mas -4901
PMU: mainFlowOfLowVoltage :     No9 :Cap is 9724 , low_rate is 97, dsoc is 9698, capnow is 9750, capzero is 76, delta cc is -5, delta cc ori is -6
PMU: mainFlowOfLowVoltage :     No10 :temp_mas is -581, offset_mas is -445, value is -582, final value is -5
PMU : set_current_time2register : second is 1435070859, hour is 398630
[drivers/input/touchscreen/zforce_i2c.c-688] zforce_i2c_close()
PMU:STATUS= 7: IBAT= -68: VSYS= 4145250: VBAT= 4144650: DSOC= 9698: RSOC= 9700: cc_delta=0: rrf= 0
[zForce_ir_touch_recv_data-224] command Deactivate ...
[drivers/input/touchscreen/zforce_i2c.c-672] zforce_i2c_open()
[zForce_ir_touch_recv_data-227] command Activate (0) ...
[zForce_ir_touch_recv_data-236] command Resolution (0) ...
[zForce_ir_touch_recv_data-262] command Frequency (0) ...
[zForce_ir_touch_recv_data-245] command Configuration ...
[drivers/input/touchscreen/zforce_i2c.c-688] zforce_i2c_close()
[zForce_ir_touch_recv_data-224] command Deactivate ...
Wifi / BT power control 1
_ntx_wifi_power_ctrl() end.

Dongle Host Driver, version 5.90.125.120.1
Compiled in /work/mx6sl/AlyssumNetronix/vendor_drivers/BCM43XX_sdio_5_90_125_120_1_Android-0229-2012/open-src/src/dhd/linux/../.. on Feb 26 2015 at 11:42:22
mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
mmc2: queuing unknown CIS tuple 0x80 (7 bytes)
mmc2: queuing unknown CIS tuple 0x80 (8 bytes)
mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
mmc2: queuing unknown CIS tuple 0x80 (5 bytes)
mmc2: queuing unknown CIS tuple 0x80 (5 bytes)
mmc2: new high speed SDIO card at address 0001
F1 signature read @0x18000000=0x1591a962
DHD: dongle ram size is set to 245760(orig 245760)
wl_iw_attach thr:5de2 started
wl_iw_bt_init thr:5de3 started
dhd_attach thr:5de4 started
dhd_attach thr:5de5 started
dhd_attach thr:5de6 started
dhd_bus_download_firmware():fw_path=/lib/firmware/wc121/fw_bcm43362a2.bin,nv_path=/lib/firmware/wc121/nvram.txt
dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
Firmware up: op_mode=1, Broadcom Dongle Host Driver mac=78:45:61:06:eb:57
Firmware version = wl0: Apr 11 2014 17:50:29 version 5.90.195.89.23 FWID 01-83cee08a
Broadcom Dongle Host Driver: register interface [eth0] MAC: 78:45:61:06:eb:57
wl_iw_set_essid: join SSID=snowcrash ch=8
[drivers/input/touchscreen/zforce_i2c.c-672] zforce_i2c_open()
[zForce_ir_touch_recv_data-227] command Activate (0) ...
[zForce_ir_touch_recv_data-236] command Resolution (0) ...
[zForce_ir_touch_recv_data-262] command Frequency (0) ...
[zForce_ir_touch_recv_data-245] command Configuration ...
[root@(none) ~]# 
[root@(none) ~]# 
[root@(none) ~]# 
[root@(none) ~]# dmesg
oc_by_voltageMethod : VBAT is 4152600 [uV], soc is 9900 [0.01%] ----------
PMU: ricoh61x_battery_resume : soc_current(9708), soc_voltage(9900), Diff(-192) ==========
PMU: update_rsoc_on_currentMethod : Current Method. state(7), dsoc(9708), rsoc(9700), init_pswr(97), cc_delta(0) ----------
PMU FG_RESET : calc_capacity : capacity 97 init_pswr 97 cc_delta 0
PMU:check_charge_status_2 Resume Sus_soc(9708), cc(0)
PMU : set_current_time2register : second is 1435070771, hour is 398630
drivers/input/keyboard/tle4913_keypad.c(79): gpio140,val=1
PMU FG_RESET : calc_capacity_2 : capacity 9700 init_pswr 97 cc_delta 0
PMU: ricoh61x_battery_resume : STATUS(7), DSOC(9708), RSOC(9700), init_pswr*100(9700), cc_delta(0) ====================
USB Gadget resume begins
fsl_udc_resume, Wait for wakeup thread finishes
PM: resume of devices complete after 546.383 msecs
PM: Finishing wakeup.
Restarting tasks ... done.
cpufreq_set_governor():set policy "interactive"
cpufreq_restore_default_governor():restore policy "interactive"
restore vcom from -2300mV to -2300mV
TPS65185 temprature data = 0x17,23
mmc2: card 0001 removed
PMU: mainFlowOfLowVoltage :     Noxx : cc_delta_cap is -2, cc_delta_cap_now is 0, last_cc_delta_cap is 0
PMU: mainFlowOfLowVoltage :     Noxx : temp_cc_delta_cap is -2, after temp_cc_delta_cap_mas is -266, cc_cap_mas 275
PMU: mainFlowOfLowVoltage :     No9 :Cap is 9706 , low_rate is 100, dsoc is 9706, capnow is 9720, capzero is 64, delta cc is -2, delta cc ori is -2
PMU: mainFlowOfLowVoltage :     No10 :temp_mas is -266, offset_mas is 0, value is -200, final value is -2
PMU : set_current_time2register : second is 1435070772, hour is 398630
PMU:STATUS= 7: IBAT= -18: VSYS= 4142000: VBAT= 4151400: DSOC= 9706: RSOC= 9700: cc_delta=0: rrf= 0
PMU: mainFlowOfLowVoltage :     Noxx : cc_delta_cap is -1, cc_delta_cap_now is -1, last_cc_delta_cap is 0
PMU: mainFlowOfLowVoltage :     Noxx : temp_cc_delta_cap is 0, after temp_cc_delta_cap_mas is -266, cc_cap_mas -628
PMU: mainFlowOfLowVoltage :     No9 :Cap is 9786 , low_rate is 92, dsoc is 9706, capnow is 9800, capzero is 64, delta cc is 0, delta cc ori is -1
PMU: mainFlowOfLowVoltage :     No10 :temp_mas is -766, offset_mas is -500, value is -92, final value is 0
PMU : set_current_time2register : second is 1435070801, hour is 398630
PMU:STATUS= 7: IBAT= -20: VSYS= 4156000: VBAT= 4159000: DSOC= 9706: RSOC= 9700: cc_delta=0: rrf= 0
[drivers/input/touchscreen/zforce_i2c.c-688] zforce_i2c_close()
[zForce_ir_touch_recv_data-224] command Deactivate ...
[drivers/input/touchscreen/zforce_i2c.c-672] zforce_i2c_open()
[zForce_ir_touch_recv_data-227] command Activate (0) ...
[zForce_ir_touch_recv_data-236] command Resolution (0) ...
[zForce_ir_touch_recv_data-262] command Frequency (0) ...
[zForce_ir_touch_recv_data-245] command Configuration ...
[drivers/input/touchscreen/zforce_i2c.c-688] zforce_i2c_close()
[zForce_ir_touch_recv_data-224] command Deactivate ...
[drivers/input/touchscreen/zforce_i2c.c-672] zforce_i2c_open()
[zForce_ir_touch_recv_data-227] command Activate (0) ...
[zForce_ir_touch_recv_data-236] command Resolution (0) ...
[zForce_ir_touch_recv_data-262] command Frequency (0) ...
[zForce_ir_touch_recv_data-245] command Configuration ...
PMU: mainFlowOfLowVoltage :     Noxx : cc_delta_cap is -4, cc_delta_cap_now is -4, last_cc_delta_cap is -1
PMU: mainFlowOfLowVoltage :     Noxx : temp_cc_delta_cap is -1, after temp_cc_delta_cap_mas is -223, cc_cap_mas -2508
PMU: mainFlowOfLowVoltage :     No9 :Cap is 9746 , low_rate is 96, dsoc is 9703, capnow is 9770, capzero is 74, delta cc is -3, delta cc ori is -4
PMU: mainFlowOfLowVoltage :     No10 :temp_mas is -679, offset_mas is -456, value is -384, final value is -3
PMU : set_current_time2register : second is 1435070830, hour is 398630
PMU:STATUS= 7: IBAT= -61: VSYS= 4151250: VBAT= 4148000: DSOC= 9703: RSOC= 9700: cc_delta=0: rrf= 0
[drivers/input/touchscreen/zforce_i2c.c-688] zforce_i2c_close()
[zForce_ir_touch_recv_data-224] command Deactivate ...
[drivers/input/touchscreen/zforce_i2c.c-672] zforce_i2c_open()
[zForce_ir_touch_recv_data-227] command Activate (0) ...
[zForce_ir_touch_recv_data-236] command Resolution (0) ...
[zForce_ir_touch_recv_data-262] command Frequency (0) ...
[zForce_ir_touch_recv_data-245] command Configuration ...
TPS65185 temprature data = 0x17,23


