Register Guidelines E-Books Search Today's Posts Mark Forums Read

Go Back   MobileRead Forums > E-Book Readers > Amazon Kindle > Kindle Developer's Corner

Notices

Reply
 
Thread Tools Search this Thread
Old 12-05-2007, 11:11 PM   #1
igorsk
Wizard
igorsk reads XML... blindfoldedigorsk reads XML... blindfoldedigorsk reads XML... blindfoldedigorsk reads XML... blindfoldedigorsk reads XML... blindfoldedigorsk reads XML... blindfoldedigorsk reads XML... blindfoldedigorsk reads XML... blindfoldedigorsk reads XML... blindfoldedigorsk reads XML... blindfoldedigorsk reads XML... blindfolded
 
Posts: 3,443
Karma: 52235
Join Date: Sep 2006
Location: Belgium
Device: PRS-500/505/700, Kindle, Cybook Gen3, Words Gear
Kindle boot log


Code:
U-Boot 1.1.2 (Oct 29 2007 - 16:35:25)

*** Welcome to Kindle ***

U-Boot code: A3F00000 -> A3F3FA6C  BSS: -> A3F77850

REV2 Bootloader: Kindle 400 MHz REV2 Board, Revision #9
 Boot block version: 20070525
 Checksum: 0x9F132881
 Buildrev: 292-Kindle-012138
 IOC Firmware Version #63

RAM Configuration:
 Bank #0: 0xA0000000 64 MB
Flash Configuration:
 Bank #0: 0x00000000 128 MB
 Bank #1: 0x04000000 128 MB
NAND Configuration:
 256 MB
BML_Init success
BML_Open success
**************** device info  *******************
nPgsPerBlk = 64
nSctsPerPg = 4
nNumOfUsBlks = 2002
*************************************************
bml open success
pi->nNumOfPartEntry: 10Success loading partition
load env done
op_amp#=65535
gain#=0
rve#=1015
panel#=010_01_23
panel#=010_01_23
serial#=B001BAB074xxxxxxx
usb_force_sleep: hw_flags.disable_pdc_suspend = 0
waiting for CLKREADY
Mode reg = 0x00000000
soft resetting device controller
power switch is on
Update  battery level: >3720mV
Boot    battery level: >3680mV
Alert   battery level: >3600mV
Current battery level:  3911mV (bootable)

Loading partition "Standard Kernel" into 0xA2000000... Success
Loading partition "Standard Initrd" into 0xA2E20000... Success

iminfo a2000000 a2e20000

## Checking Image at a2000000 ...
   Image Name:   Linux-2.6.10-lab126
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1236608 Bytes = 1.2 MB
   Load Address: a0008000
   Entry Point:  a0008000
   Verifying Checksum ... OK

## Checking Image at a2e20000 ...
   Image Name:   initrd_fs.gz
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    689536 Bytes = 673.4 KB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

bootm a2000000 a2e20000
## Booting image at a2000000 ...
   Image Name:   Linux-2.6.10-lab126
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1236608 Bytes = 1.2 MB
   Load Address: a0008000
   Entry Point:  a0008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at a2e20000 ...
   Image Name:   initrd_fs.gz
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    689536 Bytes = 673.4 KB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux................................................................................ done, booting the kernel.
Linux version 2.6.10-lab126 (build@lab126-build) (gcc version 3.4.2) #1 Mon Oct 29 16:38:09 PST 2007
CPU: XScale-PXA255 [69052d06] revision 6 (ARMv5TE)
CPU: D VIVT undefined 5 cache
CPU: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Machine: Fiona Platform
Fiona Board Resistance : 150 mOhms
Memory policy: ECC disabled, Data cache writeback
Memory clock: 99.53MHz (*27)
Run Mode clock: 398.13MHz (*4)
Turbo Mode clock: 398.13MHz (*1.0, inactive)
Built 1 zonelists
Kernel command line: console=ttyS2,115200n8 root=/dev/rd/0 initrd=/linuxrc rw reboot=hard
reserved 4096 bytes at a3fff000 for boot globals
reserved 122880 bytes at a3fe1000 for framebuffer
PID hash table entries: 512 (order: 9, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 61456KB available (2070K code, 357K data, 100K init)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 673K
NET: Registered protocol family 16
Recalculated watermarks:
  wan:      3603 (was 3603)
  low:      3586 (was 3586)
  critical: 3536 (was 3536)
REV2 board detected
Power transition failed err=-5 for pnlcd video display class
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PXA CPU frequency change support initialized
NetWinder Floating Point Emulator V0.97 (extended precision)
FPOW: Fiona Power Management Driver v0.54
squashfs: version 3.0 (2006/03/15) Phillip Lougher
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
Initializing Cryptographic API
WATER: Disabling IOC voltage reporting, initing our own timer...
Battery Voltage: 3881 mVolts (raw: 3854 mVolts)
V[1] : ~3881~
A[1] : ~181~
T[1] : ~26~
OP Amp Offset : Uninitialized
Op Amp Gain Correction : Uninitialized
Voltage Reference Correction Factor : 1015 / 1000
IOC: Fiona IOC Driver v1.0, IOC FW version #63
Battery: 3.911 Volts, 26 Degrees C, 164 mA Draw, DISCHARGING, 72%
PNLCD: Fiona PNLCD Driver v0.94
KEYBOARD: Fiona Keyboard Driver v1.0
ppoke driver: Major: 207  Rev. 4  Kernel v.2.6.10-lab126
/proc/peek initialized.
/proc/poke initialized.
ttyS0 at MMIO 0x40100000 (irq = 15) is a FFUART
ttyS1 at MMIO 0x41600000 (irq = 0) is a HWUART
ttyS2 at MMIO 0x40700000 (irq = 13) is a STUART
io scheduler noop registered
RAMDISK driver initialized: 8 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
wan: AnyDATA DTEV WAN module driver 0.8.4
i2c /dev entries driver
i2c_adapter i2c-0: found device 0x1a
Advanced Linux Sound Architecture Driver Version 1.0.6 (Sun Aug 15 07:17:53 2004 UTC).
soc: version 0.7 liam.girdwood@wolfsonmicro.com
wm8971: WM8971 audio codec 0.2.3
soc: WM8971 <-> pxa2xx-i2s mapping ok
ALSA device list:
  #0: WM8971 Portable Codec (SoC)
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
starting initrd...
eink_fb: /dev/fb/0 frame buffer device, using 471K for video memory
eink_fb: Apollo Display Driver 1.00
xsr: module license 'Samsung Proprietary' taints kernel.
Samsung XSR Core 1.2.1-lab126-2
elevator: using noop as default io scheduler
Samsung STL 1.2.1-lab126-2
Samsung RFS 1.2.1-lab126-2
kjournald starting.  Commit interval 5 seconds
EXT3 FS on stl8, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
starting init...
dosfsck 2.11-lab126 (7 Dec 2006)
dosfsck 2.11-lab126, 7 Dec 2006, FAT32, LFN
Checking we can access the last sector of the filesystem
Boot sector contents:
System ID "mkdosfs"
Media byte 0xf8 (hard disk)
       512 bytes per logical sector
      2048 bytes per cluster
        32 reserved sectors
First FAT starts at byte 16384 (sector 32)
         2 FATs, 32 bit entries
    386048 bytes per FAT (= 754 sectors)
Root directory start at cluster 2 (arbitrary size)
Data area starts at byte 788480 (sector 1540)
     96416 data clusters (197459968 bytes)
8 sectors/track, 1 heads
         0 hidden sectors
    387204 sectors total
Checking for unused clusters.
Checking free cluster summary.
/dev/stl0/9: 293 files, 7117/96416 clusters
mount: Mounting /dev/mmc/blk0/part1 on /mnt/mmc failed: No such file or directory
system: processing module dependencies
system: loading module pdc
pdc: version 1.0
pdc: IRQ 26
system: loading module usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
system: initializing eInk driver for rootfs use
eink_fb: /dev/fb/0 frame buffer device, using 588K for video memory
eink_fb: Apollo Display Driver 1.00
eink_fb: write_eink_which, size=50327
eink_fb: curr_count=0 write_size=50327
eink_fb: done, status=1
1+0 records in
1+0 records out
system: initializing random number generator
system: initializing USB gadget driver
g_file_storage gadget: controller 'pdc' not recognized
g_file_storage gadget: File-backed Storage Gadget, version: 28 July 2004
g_file_storage gadget: Number of LUNs=2
system: initializing audio configuration for REV2 or higher
system: initializing audio driver defaults
system: initializing network configuration
system: setting "conservative" processor power mode
system: starting processor watchdog
SA1100/PXA2xx Watchdog Timer: timer margin 60 sec
watchdogd 0.1 Copyright (C) 2007 Lab126, Inc.  All rights reserved.
system: starting network connection watchdog
netwatchd 0.5 Copyright (C) 2007 Lab126, Inc.  All rights reserved.
system: starting CVM memory watchdog
nomkd 0.7 Copyright (C) 2006-2007 Lab126, Inc.  All rights reserved.
system: starting TPH monitor
system: starting tphserver
tphserver 0.2 Copyright (C) 2007 Lab126, Inc.  All rights reserved.
system: starting booklet framework



Welcome to Kindle!

kindle login:
igorsk is offline   Reply With Quote
Old 12-07-2007, 07:33 PM   #2
Nate the great
Sir Penguin of Edinburgh
Nate the great ought to be getting tired of karma fortunes by now.Nate the great ought to be getting tired of karma fortunes by now.Nate the great ought to be getting tired of karma fortunes by now.Nate the great ought to be getting tired of karma fortunes by now.Nate the great ought to be getting tired of karma fortunes by now.Nate the great ought to be getting tired of karma fortunes by now.Nate the great ought to be getting tired of karma fortunes by now.Nate the great ought to be getting tired of karma fortunes by now.Nate the great ought to be getting tired of karma fortunes by now.Nate the great ought to be getting tired of karma fortunes by now.Nate the great ought to be getting tired of karma fortunes by now.
 
Nate the great's Avatar
 
Posts: 10,524
Karma: 3569525
Join Date: Apr 2007
Location: DC Metro area
Device: Shake a stick plus 1
Quote:
Welcome to Kindle!

kindle login:
Woohoo!
Nate the great is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Opus cannot boot, stuck on boot screen baloma Bookeen 35 11-13-2010 04:20 AM
Connect Kindle 1 with TTL, can't boot.pls Help michaelyzy Kindle Developer's Corner 0 05-12-2010 02:25 AM
kindle dx cannot boot!! pls help me chinaet Amazon Kindle 3 07-19-2009 08:23 PM
New Member Log In rcota@ec.rr.com Introduce Yourself 3 05-03-2008 10:46 AM
Kindle boot logs Nate the great Kindle Developer's Corner 10 11-27-2007 09:56 AM


All times are GMT -4. The time now is 01:12 AM.


MobileRead.com is a privately owned, operated and funded community.