Classic Quite dead nook classic. Please help

[Fibogreg]

Hello guys,

You are my last hope. I have old Nook BNRV100 which is dead. Charging light is working. That is all. Nothing on a screen. It is newer version with nand memory instead of sd card. I have connected through the serial port. That are two options I get.

U-Boot 1.1.6 (Aug 2 2010 - 23:02:38) for SMDK6410


CPU: S3C6410@532MHz
Fclk = 532MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART
(SYNC Mode)
Board: SMDK6410
DRAM: 256 MB
Flash: 0 kB
SD/MMC: Movi_set_capacity
ofsinfo.last(0x3b9ffe)
ofsinfo.bl1(0x3b9fee)
ofsinfo.env(0x3b9fce)
ofsinfo.bl2(0x3b9dce)
ofsinfo.kernel(0x3b7dce)
ofsinfo.rootfs(0x3b3dce)
hsmmc_set_gpio()
movi_init: hsmmc_reset()
hsmmc_init()
HM_CLKCON (0x2c) = 0x4003
HM_CONTROL2(0x80) = 0xc00f4120
HM_CONTROL3(0x84) = 0x00008080
HM_HOSTCTL(0x28) = 0x00
1909 MB (moviNAND)
HM_HOSTCTL(0x28) = 0x00
HM_CLKCON (0x2c) = 0x0103
HM_CONTROL2(0x80) = 0xc00f4120
HM_CONTROL3(0x84) = 0x00008080
*** Warning - bad CRC or moviNAND, using default environment

In: serial
Out: serial
Err: serial
hsmmc_set_gpio2() for 2nd SD card.
hsmmc_init2()
HM_CLKCON (0x2c) = 0x4003
HM_CONTROL2(0x80) = 0xc00f4120
HM_CONTROL3(0x84) = 0x00008080
969 MB real card size 3c8c0000
HM_CLKCON (0x2c) = 0x0103
HM_CONTROL2(0x80) = 0xc00f4120
HM_CONTROL3(0x84) = 0x00008080

2nd SD card was detected!
movi_get_size: 3c8c0000
mfg img checksum 00000000
expected checksum 8274ba05
Manufacturing section checksum verification failed, boot as usual
U-boot...<0>„<0><0><0><0> „ B<0><0><0>OK

U-Boot 1.1.6 (Aug 2 2010 - 23:02:38) for SMDK6410


CPU: S3C6410@532MHz
Fclk = 532MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART
(SYNC Mode)
Board: SMDK6410
DRAM: 256 MB
Flash: 0 kB
SD/MMC: Movi_set_capacity
ofsinfo.last(0x3b9ffe)
ofsinfo.bl1(0x3b9fee)
ofsinfo.env(0x3b9fce)
ofsinfo.bl2(0x3b9dce)
ofsinfo.kernel(0x3b7dce)
ofsinfo.rootfs(0x3b3dce)
hsmmc_set_gpio()
movi_init: hsmmc_reset()
hsmmc_init()
HM_CLKCON (0x2c) = 0x4003
HM_CONTROL2(0x80) = 0xc00f4120
HM_CONTROL3(0x84) = 0x00008080
HM_HOSTCTL(0x28) = 0x00
1909 MB (moviNAND)
HM_HOSTCTL(0x28) = 0x00
HM_CLKCON (0x2c) = 0x0103
HM_CONTROL2(0x80) = 0xc00f4120
HM_CONTROL3(0x84) = 0x00008080
*** Warning - bad CRC or moviNAND, using default environment

In: serial
Out: serial
Err: serial
hsmmc_set_gpio2() for 2nd SD card.
hsmmc_init2()
HM_CLKCON (0x2c) = 0x4003
HM_CONTROL2(0x80) = 0xc00f4120
HM_CONTROL3(0x84) = 0x00008080
0 MB

2nd SD card was NOT found!

First boot is with a upgrade sd card made by nookdevs instructions.
I know it is an ancient device but I really hope anyone can help me
Is there any option to bring it back to life?