Register Guidelines E-Books Search Today's Posts Mark Forums Read

Go Back   MobileRead Forums > E-Book Readers > Android Devices > enTourage eDGe

Notices

Reply
 
Thread Tools Search this Thread
Old 08-06-2011, 05:58 AM   #1
JTY
Member
JTY began at the beginning.
 
Posts: 20
Karma: 10
Join Date: Aug 2011
Device: Entourge Pocket Edge
PE Hardware serial console

Just opened my WSOD PE to look for the heat source that caused WSOD.
I took some pictures from the components and found debugging serial port that is jused for linux main console.

Check attched picture, serial port marked with red circle.


Here's also output from the serial console:


U-Boot 2009.01-rc1-svn1084 (Feb 15 2011 - 12:04:39)
Marvell version: 1.1.1.1 PXAxxx

ESI version: 2.0.3 (1) <<EdgeJr>>

MARVELL PXAXXX series.
Based on 88SV331xV5 Core with ARM926 LE CPU.
Code original base is u-boot-arm 2009.01-rc1.

DRAM: 512 MB
NAND: detect chip id d7ec on cs 0, Samsung 32Gibx8
SPI NOR: SF: Got idcode c2 20 17 c2 20
SF: Detected MX25L6405D with page size 256, total 88In: serial
Out: serial
Err: serial
Net: u2o-eth
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x1200000, size 0x100000
Failed to detect legacy BBM, searching for new BBM...
Detected New BBM Table
Found main block at 0, back at 1
Factory marked bad blocks:
No factory marked bad blocks found!!
1048576 bytes read: OK
read zImage from SPI NOR (sf read 0x500000 0x100000 0x300000)
Ready to boot zImage from 500000


Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Linux version 2.6.34 (buildmaster@zeke) (gcc vinexa
cmdline:
[ 0.000000] bootloader: ( jb @ jb0000] Kernel command line: mem=512M
console=ttyS1,115200 flipp-cache hash table en)
[
[ 0.000000] .init : 0xc0008000 - 0xc00e8000 ( 8vice 80x30
[ 0.000000] ram_console: buffer (null), invalid ET: Registered protocol
family 16
[ 0.226420.354597] bio: create slab <bio-0> at 0
[ 0.356051] SCSI x 1-0020: gpios 128..143 on a pcf8575 (irq 107)d Linux
Sound Architecture Driver Version 1.0.22.1.
[ source
[ 0.367569] NET: Registered protocol family TCP: Hash tables configured
(established 16384 bered udp transport modu.
[ 0.369056] RPC: 0.483579] Freeing initrd memory: 24576K
[ .1.29 [Flags: R/O].

[ 0.493398] fu(default)
[ 0.497697] pxa168fb_probe: NUM_CLK_DIVS =yS1] enabled
[ 1.076489] No Read Stobe delay2 at MMIO 0xd4026000 (irq = 29) is a
STUART
[ 1.079626] Controller is using falling edge to detect RE
[ 1.085026] NDTR1 o factory bad block!!
start from f9c00000, size 6400000
[ 1.173316] Reserved pock: 8191
[ 1.199536] block: 2454 00 : "bootloader-alt"
[ 1.228616] 0x000000b00000-0x000000c00000 : "environment-alt"
[ 1.23517100-0x000100000000 : "MRVL_BBM"
"kernel-alt"
[ chip on cs 1!
[ 1.280530] UBI: attach96 (aligned 4096)
[ 1.306867] UBI: data offset: 8192
[ 6.573060] UBI: attached mtd6 to ubi0
[ 6.57687: wear-leveling threshold: 256
[ 6.605505] UBI: n8
[ 6.629986] UBI: max/mean erase counter: 1/30] Creating 5 MTD partitions
on "pxa2xx_spi_nor":
[ 6.66200-0x000000800000 : "kernelrecovery"
[ 6.693446] PPP generic driver version 2.4.2
[ 6.723310] tun: (C) 1999-2004 Max Krasnya[ 6.750484] usbcore:
registered new interface driver rtl8150
[ er
[ 6.782059] u2h regbase 0xe09a2000 phyb[ 6.825762] pxau2h-ehci
pxau2h-ehci: USB 2.0 started,

[ 6.857002] usbco)
egbase 0xe09aa000 phybase 0xe09ae000 irq 44rface driver option
[ 6.921RQF_DISABLED is not guaranteed on shared IRQget: Mass Storage
Function, version: 2009/09/11

[[ 7.002136] gpio_keys_setup_key: irq=195, gpio=131
[ 137
[ 7.034469] gpio_keys_setup_key: irq=199, gtup_key: irq=151, gpio=87
[ 7.065520] gpio_keys, type 5 code 0x3(3) value 1
[ 7.095033] [gt1
[ 7.120366] [esikbd_probe] finished successfully
[ 7.124983] [esikbd_init] left
[ 7.128674] input: pxa27x-keypad as /class/input/input2
[ 7.134391] ofm : I2C device probe
[ 7.238429] usb 1-1: new high speed USB device using pxau2h-ehci and
address 2
[ 7.245940] input: ofm as /class/input/input3
[ 7.357495] ofm : clear pending motion
[ 7.365957] ofm : I2Ced
ce init Successr alarms
[ 7.405192] rtc-ds1307 0-0068: rtc core: registered ds1337 as rtc0
[ 7.412176]67] Bluetooth: Virtual HCI driver ver 1.3
[ 7.460938] Bluetooth: HCICI controller on MMC [pxa-sdh.3] using DMA
[ 7.464K log 'log_main'
[ 7.524362] logger: created 256K log 'log_events'
[ 7.559263] No device for DAI Grayback-ssp
[ 7.566046] asoc: WM8978 HiFi <-> pxa3xx-ssp1 mapping ok
7.543133] No device for DAI pxa3xx-ssp1
[ 7.547204] No device for DAI pxa3xx-ssp2
[ 7.551215] No device for DAI pxa3xx-ssp3
[ 7.55 ox 7.559263] No device for DAI gistered protocol family 15
[ 7.716997] Bluetooth: etooth: RFCOMM socket layer initialized
[ 7.745381] Bluetooth: RFCOMM ver 1.11
[ 7.749161] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 7.754469] Bluetooth: BNEP filters: protocol multicast
[ 7.759722] Bluetooth: HIDP (Human Interface Emulation) ver 1.2

[ 7.811150] your service
processor detected.
[ 7.823579] pxa168fb_ovly: frame buffer device was loaded to /dev/fb1
<Ovly>.
[ 7.878699] rtc-ds1307 0-0068: setting system clock to 2011-08-04
09:46:26 UTC (1312451186)
[ 7.887099] OmniVision ov3640 senso d your service
[ 7.937004] ov3640 power on (reset active)
[ 7.985111] ov3640 power on (reset inactive)
[ 7.993103] OmniVision ov3640 sensor detected
[ 8.086624] ccic_ctlr_power_down: ccic is power downed!!!
[ 8.092036] OV3640 i2c-probe detected
[ 8.140063] OmniVision ov7740 sensor driver, at your service
[ 8.146197] RAMDISK: gzip image found at block 0
[ 8.790456] VFS: Mounted root (ext2 filesystem) on device 1:0.
[ 8.796584] Freeing init memory: 896K
[ 8.849028] init: /init.pxa168.rc: 161: user option init.pxa168.rc: 175:
user option requires a user id
[ 8.882182] init: /init.pxa168.rc: 179: user option requires a user id
rc: 168: user option requires a user id
[ 8.869014] init: /init.pxa168.rc: 172: user option requires a user id
[ 8.580init.pxa168.rc: 175: user option requires a user id
[ 8.882182] init: /init.pxa168.rc: 179: user option requires a user id
[ 9.411953] init: do_mount: calling mount: dev none dir /acct s cgroup
flags 0x0 options cpuacct
[ 9.421823] init: do_mount: calling mount: dev tmpfs dir /mnt/asec s
tmpfs flags 0x0 options mode=0755,gid=1000
[ 9.477258] init: do_mount: calling mount: dev rootfs dir / s rootfs
flags 0x21 options (null)
[ 9.708437] init: do_mount: calling mount: dev none dir /dev/cpuctl s
cgroup flags 0x0 options cpu

[ 9.762265] init: do_mount: calling mount: dev ubi:system dir /system s
ubifs flags 0x1 options (null)
[ 11.286700] mmc1: new high speed SDIO card at address 0001
[ 11.461587] UBIFS: mounted UBI device 0, v: media format: w4/r0
(latest is w4/r0)
[ 11.492523] UBIFS: default compressor: lzo
[ 11.496658] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 11.503447] init: do_mount: calling mount: dev ubi:userdata dir /data s
ubifs flags 0x6 options (null)
dia format: : mounted UBI device 0, volume 1, name [ 11.668222]
UBIFS: default compressor: lzo
[ 11.672314] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 11.687027] init: do_mount: calling mount: dev ubi:cache dir /cache s
ubifs flags 0x6 options (null)
[ 11.855858] UBIFS: mounted UBI device 0, volum 11.883190] UBIFS: default
compressor: lzo
[ 11.887316] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[ 11.918426] init: do_mount: calling mount: dev ubi:storage dir
/intstorage s ubifs flags 0x6 options (null)
format: w4/r0 (latest w4 1.883190] UBIFS: default compressor: lzo
[ 11.887316] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[ 11.918426] init: do_mount: calling mount: dev ubi:storage dir
/intstorage s ubifs flags 0x6 optionsUBIFS: journal )
dir /var/run s tmpfs flags 0x0 options (null)
[ 12.178410] init: do_mount: calling mount: dev varlock dir /var/lock s
tmpfs flags 0x0 options (null)
[ 12.187727] init: do_mount: callint: dev none dir /proc/bus/usb s usbfs
flags 0x0 options (null)
[ 12.396762] init: provisioned = 0
[ 12.402939] init: esi_android_init: entry
[ 12.407033] init: app permissions check: BEGIN
[ 26.379685] init: fix_perms returned 0 (0x0)

[ 26.383970] init: app permissions check: END
[ 26.388315] init: Filesystem check: BEGIN
[ 27.348714] init: Filesystem check: rc = 0x00000000
[ 27.353603] init: Filesystem check: END
[ 27.357507] init: esi init script: BEGIN
[ 27.581028] serio: Serial port ttyS2
[ 27.584712] wacdsu_connect: esi id set to 1
[ 27.590460] input: Wacom DSU as /class/input/input6
[ 28.041465] ep3522base: not flipped
[ 28.044959] ep3522base: locale = en_US
[ 545] [ep3522if_i2cRead] I2C ID: 0x48, Addr: 0x3, RdData: 0xa3
[ 28.093902] [ep3522if_i2cWrite] I2C ID: 0x48, Addr: 0x3, WrData: 0x23
767] [ep3522if_ControllerInit] about to wait for Ready after INIT_SYS_RUN
[ 28.081991] ep3522if: wait_for_r:ter[545] [ep3522if_i2cRead] I2C ID:
0x48, Addr: 0x3, RdData: 0xa3
[ 28.093902] [ep3522if_i2cWrite] I2C ID: 0x48, Addr: 0x3, WrData: 0x23
[ 29.096015] ep3522fb_probe(): Back from Controller Init
[ 29.101243] ... Startup Mode, painting WHITE
[ 32.286210] ... reading the serial flash memory ddress=0x074000, size=2)
[ 32.317763]reading the serial flash memory (address=0x074000, size=4228)
[ 32.385132] ... reading the serial flash memory eneral_create_files:
exiting... ret = 0
[ 32.416005] ep3522base: done with esi_general...
[ 32.420703] ** [ep3522fb_probe] About to paint Initing Screen
al_22.c at line 369: copying table
[ 32.406836] drivers/video/esi-general_22.c at line 398:
eneral_create_files: exiting... ret = 0
[ 32.416005] ep3522base: done with esi_general...
[ 32.420703] ** [ep3522fb_probe] About to paint Initing Screen
[ 32.640168] ep3522if: wait_for_ready: New HighWater = 3
[ 32.900168] ep3522if: wait_for_ready: New HighWater = 25

[ 33.122919] BMM init with size=32MB
[ 33.136476] init: init script returned 0 (0x0)
[ 33.140929] init: esi init script: END
[ 33.144685] init: esi_android_init: mounting on sdcard
[ 33.178'
sh: can't access tty; job control turned off
# 83198] init: esi_android_init: SKU = '100-9500011-BLK'
[ 33.188927] init: esi_android_init: SN = 'BF30145100B69'
[ 33.215239] init: cannot find '/system/etc/install-recovery.sh',
disabling 'flash_r'
sh: can't access tty; job control turned off
# [ 33.434687] warning: `adbd' uses 32-bit capabilities (legacy support in
# use)
[ 33.442822] enabling adb
[ 33.450533] adb_open
[ 58.306780] mcypt: module license 'Marvell Proprietary' taints kernel.
[ 58.313324] Disabling lock debugging due to kernel taint
[ 58.598472] wlan_sdio mmc1:0001:1: firmware: requesting
mrvl/helper_sd.bin
[ 58.674753] init: untracked pid 6319 exited
[ 58.688456] wlan_sdio mmc1:0001:1: firmware: requesting mrvl/sd8688.bin
[ 58.945935] init: untracked pid 6325 exited
[ 59.193335] pxa168fb resuming...
[ 59.199798] kernel/power/earlysuspend.c at line 165:
request_suspend_state new_state = on
[ 59.223019] request_suspend_state: wakeup (3->0) at 59217449854
(2011-08-04 09:47:17.844467076 UTC)
[ 59.504561] WLAN FW is active
[ 59.782073] [tsc2007write_state] entered, new_state 1
[ 59.794115] drivers/input/touchscreen/tsc2007.c at line 399:
turn_on_esi_touchscreen lockstate = 0

[ 65.032243] init: sys_prop: permission denied uid:7000
name:dev.esid.rstpid
[ 96.260014] _pxa168fb_suspend(): state = 7] _pxa168fb_suspend(): state =
2.
): state = 2.
[ 96.268718] kernel/power/earlysuspend.c at line 165:
request_suspend_state new_state = mem
[ 96.277045] request_suspend_state: sleep (0->3) at 96271592930
(2011-08-04 09:47:54.898610152 UTC)
[ 967] _pxa168fb_suspend(): state = 2.
[ 116.005474] PM: Syncing filesystems ... done.
[ 116.086083] PM: Preparing system for mem sleep
[ 116.094118] Freezing user space processes ... (elapsed 0.00 seconds)
done.
[ 116.106348] Freezing remaining freezable tasks ... (elapsed 0.00 seconds)
done.
[ 116.114006] PM: Entering mem sleep
[ 116.168123] Suspending console(s) (use no_console_suspend to debug)
Attached Thumbnails
Click image for larger version

Name:	serial.jpg
Views:	399
Size:	910.0 KB
ID:	75221  
JTY is offline   Reply With Quote
Old 08-06-2011, 07:32 AM   #2
ivanjt
Guru
ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.
 
Posts: 855
Karma: 1027478
Join Date: Aug 2010
Location: South of France
Device: kindle dx; eDGe
JTY, could you please take more pictures and if possible use a couple of lights - on either side of board to remove the glare an evenly light everything. I'm trying to build a list of what components are used. Thanks in advance.
ivanjt is offline   Reply With Quote
Old 08-06-2011, 08:06 AM   #3
JTY
Member
JTY began at the beginning.
 
Posts: 20
Karma: 10
Join Date: Aug 2011
Device: Entourge Pocket Edge
Quote:
Originally Posted by ivanjt View Post
JTY, could you please take more pictures and if possible use a couple of lights - on either side of board to remove the glare an evenly light everything. I'm trying to build a list of what components are used. Thanks in advance.
Photos are originally much larger, but the forum software resizes them
I will try and upload them to my own server.
JTY is offline   Reply With Quote
Old 08-06-2011, 12:28 PM   #4
emusan
lol
emusan can extract oil from cheeseemusan can extract oil from cheeseemusan can extract oil from cheeseemusan can extract oil from cheeseemusan can extract oil from cheeseemusan can extract oil from cheeseemusan can extract oil from cheeseemusan can extract oil from cheese
 
emusan's Avatar
 
Posts: 472
Karma: 1031
Join Date: May 2011
Device: eDGe
this could be interesting... Try using macro mode as well(if you didn't already), its the one with a flower symbol on most camera's. You can also email me the picture and I can host it if you want.
emusan is offline   Reply With Quote
Old 08-06-2011, 12:56 PM   #5
Gunnerp245
Gadget Freak
Gunnerp245 ought to be getting tired of karma fortunes by now.Gunnerp245 ought to be getting tired of karma fortunes by now.Gunnerp245 ought to be getting tired of karma fortunes by now.Gunnerp245 ought to be getting tired of karma fortunes by now.Gunnerp245 ought to be getting tired of karma fortunes by now.Gunnerp245 ought to be getting tired of karma fortunes by now.Gunnerp245 ought to be getting tired of karma fortunes by now.Gunnerp245 ought to be getting tired of karma fortunes by now.Gunnerp245 ought to be getting tired of karma fortunes by now.Gunnerp245 ought to be getting tired of karma fortunes by now.Gunnerp245 ought to be getting tired of karma fortunes by now.
 
Gunnerp245's Avatar
 
Posts: 1,129
Karma: 1043832
Join Date: Nov 2007
Location: US
Device: EE, PE, Note 8
Question

Quote:
Originally Posted by JTY View Post
...Here's also output from the serial console...
How was you able to get this data?
Gunnerp245 is offline   Reply With Quote
Old 08-06-2011, 01:46 PM   #6
vicinc
Guru
vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.
 
Posts: 733
Karma: 443
Join Date: May 2011
Location: UK
Device: Pocket Edgex2(1unborked), Alex, Nook B&W, Nook Color, Nook STR
so we may have a jtag?
vicinc is offline   Reply With Quote
Old 08-06-2011, 01:47 PM   #7
vicinc
Guru
vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.
 
Posts: 733
Karma: 443
Join Date: May 2011
Location: UK
Device: Pocket Edgex2(1unborked), Alex, Nook B&W, Nook Color, Nook STR
is not that the interesting part? '/system/etc/install-recovery.sh',
disabling 'flash_r'
recovery missing?
vicinc is offline   Reply With Quote
Old 08-06-2011, 01:48 PM   #8
vicinc
Guru
vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.
 
Posts: 733
Karma: 443
Join Date: May 2011
Location: UK
Device: Pocket Edgex2(1unborked), Alex, Nook B&W, Nook Color, Nook STR
I do have ftp donated by a member for the purpose of Edge soft development can host as well.
vicinc is offline   Reply With Quote
Old 08-06-2011, 04:27 PM   #9
emusan
lol
emusan can extract oil from cheeseemusan can extract oil from cheeseemusan can extract oil from cheeseemusan can extract oil from cheeseemusan can extract oil from cheeseemusan can extract oil from cheeseemusan can extract oil from cheeseemusan can extract oil from cheese
 
emusan's Avatar
 
Posts: 472
Karma: 1031
Join Date: May 2011
Device: eDGe
Quote:
Originally Posted by Gunnerp245 View Post
How was you able to get this data?
probably by using a serial cable with his PC and then using a terminal like minicom or similar to read the output...
emusan is offline   Reply With Quote
Old 08-06-2011, 06:26 PM   #10
JTY
Member
JTY began at the beginning.
 
Posts: 20
Karma: 10
Join Date: Aug 2011
Device: Entourge Pocket Edge
Quote:
Originally Posted by vicinc View Post
so we may have a jtag?

No jtag, just plain old rs232 protocol
Just plug RX TX to the pin header, there is a MAX232 behind that pin header.
It's configured for 115.2kbps speed, i used minicom because it's the best

Via system console you can do some cool things, full access to u-boot and kernel parameters, you can even load own kernel etc.
But the best part is the kernel boots msg, there's lot of usefully information.

btw. there waas jtag pins on the motherboard for processor debugging

But still no clue what's causing WSOD.
JTY is offline   Reply With Quote
Old 08-06-2011, 06:30 PM   #11
arcticmaniac
Connoisseur
arcticmaniac can illuminate an eclipsearcticmaniac can illuminate an eclipsearcticmaniac can illuminate an eclipsearcticmaniac can illuminate an eclipsearcticmaniac can illuminate an eclipsearcticmaniac can illuminate an eclipsearcticmaniac can illuminate an eclipsearcticmaniac can illuminate an eclipsearcticmaniac can illuminate an eclipsearcticmaniac can illuminate an eclipsearcticmaniac can illuminate an eclipse
 
arcticmaniac's Avatar
 
Posts: 89
Karma: 8118
Join Date: Jul 2011
Device: entourage pe
Quote:
Originally Posted by JTY View Post
No jtag, just plain old rs232 protocol
Just plug RX TX to the pin header, there is a MAX232 behind that pin header.
It's configured for 115.2kbps speed, i used minicom because it's the best

Via system console you can do some cool things, full access to u-boot and kernel parameters, you can even load own kernel etc.
But the best part is the kernel boots msg, there's lot of usefully information.

btw. there waas jtag pins on the motherboard for processor debugging

But still no clue what's causing WSOD.
what is WSOD, ??? white screen of death ????
arcticmaniac is offline   Reply With Quote
Old 08-06-2011, 07:21 PM   #12
ivanjt
Guru
ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.ivanjt ought to be getting tired of karma fortunes by now.
 
Posts: 855
Karma: 1027478
Join Date: Aug 2010
Location: South of France
Device: kindle dx; eDGe
Quote:
Originally Posted by arcticmaniac View Post
what is WSOD, ??? white screen of death ????
Yes!

It's like the windows BSOD only worse.
ivanjt is offline   Reply With Quote
Old 08-06-2011, 07:34 PM   #13
vicinc
Guru
vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.
 
Posts: 733
Karma: 443
Join Date: May 2011
Location: UK
Device: Pocket Edgex2(1unborked), Alex, Nook B&W, Nook Color, Nook STR
can you get a rom dump please? and try to get recovery around this?
vicinc is offline   Reply With Quote
Old 08-06-2011, 07:35 PM   #14
vicinc
Guru
vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.
 
Posts: 733
Karma: 443
Join Date: May 2011
Location: UK
Device: Pocket Edgex2(1unborked), Alex, Nook B&W, Nook Color, Nook STR
can you identify the jtag pins for us. somebody was asking for those.
vicinc is offline   Reply With Quote
Old 08-06-2011, 07:36 PM   #15
vicinc
Guru
vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.vicinc has a complete set of Star Wars action figures.
 
Posts: 733
Karma: 443
Join Date: May 2011
Location: UK
Device: Pocket Edgex2(1unborked), Alex, Nook B&W, Nook Color, Nook STR
is this one of the avengers lite cheap motherboards?
vicinc is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Kindle DX serial console ebs Kindle Developer's Corner 49 11-23-2011 01:36 PM
PRS-600 Serial console (i.e. shell) over USB Xaphiosis Sony Reader Dev Corner 6 08-23-2010 12:06 AM
serial console goes to sleep - gated clock darron Kindle Developer's Corner 2 12-19-2009 09:52 PM
Serial console BlackRat iRex 3 02-19-2007 05:35 AM


All times are GMT -4. The time now is 12:14 PM.


MobileRead.com is a privately owned, operated and funded community.