After a McGyvered serial connection setup I managed to get the boot log
The error screen appears after
Code:
info shutdown_showimage:screen:waiting for cust_service screen to come up:
Another issue now is that I only had a 3.3V adapter so I only connected to the Kindle's Tx for safety
Here's the log:
Spoiler:
Code:
U-Boot 2009.08-lab126 (Apr 04 2012 - 20:06:50)
CPU: Freescale i.MX50 family 1.1V at 800 MHz
mx50 pll1: 800MHz
mx50 pll2: 400MHz
mx50 pll3: 216MHz
ipg clock : 50000000Hz
ipg per clock : 50000000Hz
uart clock : 24000000Hz
ahb clock : 100000000Hz
axi_a clock : 400000000Hz
axi_b clock : 200000000Hz
weim_clock : 100000000Hz
ddr clock : 800000000Hz
esdhc1 clock : 80000000Hz
esdhc2 clock : 80000000Hz
esdhc3 clock : 80000000Hz
esdhc4 clock : 80000000Hz
MMC: FSL_ESDHC: 0, FSL_ESDHC: 1
Board: Whitney WFO
Boot Reason: [POR]
Boot Device: MMC
Board Id: 0061405114850Q5W
S/N: B0111408210505H1
DRAM: 256 MB
Using default environment
In: serial
Out: logbuff
Err: logbuff
Quick Memory Test 0x70000000, 0xfffe000
POST done in 13 ms
Hit any key to stop autoboot: 1 0
## Booting kernel from Legacy Image at 70800000 ...
Image Name: Linux-2.6.31-rt11-lab126
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5181440 Bytes = 4.9 MB
Load Address: 70008000
Entry Point: 70008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
mxc_spi mxc_spi.0: chipselect 0 already in use
2.6.31-rt11-lab126 #1 Tue Jul 17 16:55:47 PDT 2012 armv7l
INFO:Loaded module /lib/modules/eink_fb_waveform.ko (36300 bytes)
mxc_epdc_fb mxc_epdc_fb: not use_builtin_cmap !!
INFO:Loaded module /lib/modules/mxc_epdc_fb.ko default_panel_hw_init=1 default_update_mode=1 (49672 bytes)
INFO:eink initialized... (486400 bytes)
INFO:Using default keypad setting. (not passing "kb_rev" to module)
INFO:Loaded module /lib/modules/whitney_button.ko (9268 bytes)
Press [ENTER] for recovery menu... 0 /INFO:*** Partition table verified for /dev/mmcblk0 ***
INFO:Checking for updates... (auto-pilot mode)
/dev/mmcblk0p4:
CHS=4/16/105536 size=3458203648 bytes
flag type first last lba first lba size
Partition p1:
0x00 0x0b 16 <large> 16 6754288
CHS: 0/1/1 - <large>
Partition p2:
Partition p3:
Partition p4:
INFO:Setup loop device /dev/loop0 for /dev/mmcblk0p4 + 8192
INFO:No update*.bin found; no update needed.
INFO:no updates found.
BOOTING DEFAULT.
argc == 10
argv[0]: "kinit"
argv[1]: "consoleblank=0"
argv[2]: "rootwait"
argv[3]: "ro"
argv[4]: "ip=off"
argv[5]: "root=/dev/mmcblk0p1"
argv[6]: "quiet"
argv[7]: "eink=fslepdc"
argv[8]: "video=mxcepdcfb:E60,bpp=8,x_mem=2M"
argv[9]: "console=ttymxc0,115200"
argc == 4
argv[0]: "IP-Config"
argv[1]: "-i"
argv[2]: "Linux kinit"
argv[3]: "ip=off"
IP-Config: no devices to configure
kinit: do_mounts
kinit: name_to_dev_t(/dev/mmcblk0p1) = dev(179,1)
kinit: root_dev = dev(179,1)
kinit: /dev/root appears to be a ext3 filesystem
kinit: trying to mount /dev/root on /root with type ext3
kinit: Mounted root (ext3 filesystem) readonly.
info modules:modprobe:loading module g_file_storage:
init.exe: recevent pre-start process (520) terminated with status 1
info system:start:time=4240:
info hardware:no_wan::WiFi only device. No WAN found
info modules:modprobe:loading module fuse:
info system:config:platform=yoshi,board=whitney,rev=20,proto=N,wifi=Y,wan=N:
info modules:modprobe:loading module ppp_async:
info modules:modprobe:loading module whitney_button:
info zforce:start:version=2.0b0r12:
info system:done:time=5640:
info userstore:run:time=5890,action=start:
info userstore:found_shutdown_flag::Found SHUTDOWN flag file
info display:started:time=6070:
info battery:charged:cap=63,mV=3817,mAH=733:
Welcome to Kindle!
kindle login: info hardware:no_wan::WiFi only device. No WAN found
info hardware:no_wan::WiFi only device. No WAN found
info X:load:time=7360:
info X:xorg.conf:Generating xorg.conf:
warn ttsd:upstart_ttsd_exited::
info X:makexconfig:Whitney Input device detection status:
info X:makexconfig:Keypad: OK:
info X:makexconfig:Touch device: OK:
info X:makexconfig:Accelerometer device: N/A !!:
info X:xorg.conf:xorg.conf generated:
info X:starting:time=8500:
info X:started:time=14320:
info blanket_f:module already loaded:splash:
info locale:read:lang=it_IT.utf8,lc_all=it_IT.utf8:Retrieved Language
crit lab126_gui:reboots=2,max=2:shutting down and showing customer service page:
info shutdown:begin:level=0,halt=1,special=cust_service:
info shutdown:closing password dialog::
info blanket_f:loading blanket module:shutdown:
info shutdown_showimage:screen:splashing screen:cust_service
info shutdown_showimage:screen:waiting for cust_service screen to come up:
info upstart_f:stopping_job:job=lab126:
info upstart_f:stopping_job:job=x:
info upstart_f:jobs_stopped:elapsed_ms=4410,timeout_ms=45000:
info shutdown:cust_service:starting:
info ss_cust_service:nothing to do for this shutdown mode:"cust_service":
info ss_cust_service:completed successfully::
info shutdown:cust_service:done:
info upstart_f:stopping_job:job=filesystems:
info filesystem:unmount_userstore:Unmounting UserStore:
info userstore:run:time=23850,action=stop:
info userstore:found_bootup_flag::Found BOOTUP flag file
info filesystem:rotate_log:Rotating Logs:
info filesystem:unmount_varLocal:Unmounting VarLocal:
info upstart_f:jobs_stopped:elapsed_ms=4350,timeout_ms=30000:
info shutdown:mounting root filesystem read-only::
info shutdown:syncing disks::
info shutdown:end:level=0,halt=1:
System halted.
Halting ...